Ronix 8630C Cordless LED Torch Light Instruction Manual
- June 1, 2024
- Ronix
Table of Contents
Ronix 8630C Cordless LED Torch Light
Technical Specification
Model| Light Type| Power| Flux| Illumination Range| Cct| Rotation Angle| Run
time| Degree Of Protection| Weight| Dimension
---|---|---|---|---|---|---|---|---|---|---
8630C| LED Lamp| 20V| N/A| N/A| N/A| N/A| N/A| N/A| N/A| N/A
Product Usage Instructions
User Manual
Part List:
- LED Lamp
- ON/OFF Switch
- Soft grip rubber handle
Symbols:
The following show the symbols used for the equipment. Be sure that you
understand their meaning before use.
- Read instruction manual.
- Do not touch the bulb which is hot in use or immediately after putting on the light. You may get burnt.
Important Safety Instructions
WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury.
- Read all instructions carefully before use.
- Avoid using the flashlight in damp or wet locations.
- Avoid short-circuits to prevent overheating and burns.
FAQ (Frequently Asked Questions)
Q: Is the torch light waterproof?
A: No, the flashlight is not waterproof. Avoid using it in damp or wet
conditions.
Q: How do I adjust the head angle of the torchlight?
A: The head angle can be adjusted in four stages. Refer to the user
manual for detailed instructions on adjusting the head angle.
20V CORDLESS LED TORCH LIGHT
8630C
TECHNICAL SPECIFICATION
| Model | 8630C |
|---|---|
| Light Type | High-brightness LED lamp |
| Power | 5W |
| Flux | 250lm |
| Illumination Range | >100M |
| Cct | 6500K |
| Rotation Angle | 90° |
| Run time | 6 H |
| Degree Of Protection | IP54 |
| Weight | 0.4Kg |
| Dimension | 207.3×119.32×73.5mm |
PART LIST
SYMBOLS
The following show the symbols used for the equipment. Be sure that you
understand their meaning before use.
Read instruction manual.
Do not touch the bulb which is hot in use or immediately after putting on light. You may get burnt.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following:
READ ALL INSTRUCTIONS
- Read this instruction manual and the charger instruction manual carefully before use.
- This flashlight is not waterproof. Do not use it in damp or wet locations. Do not expose it to rain or snow. Do not wash it in water.
- A short-circuit can cause a large current flow, overheating, possible burns and even a breakdown.
- Do not touch the inside of the flashlight head with tweezers, metal tools, etc.
- (2) Do not touch the battery terminals with any conductive material.
- (3) Avoid storing the battery cartridge in a container with any metal objects such as nails, coins, etc.
- If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
- If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
- Be careful not to drop.
- When the tool is not in use, always switch off and remove the battery cartridge from the tool.
- Do not store the tool in locations where the temperature may reach or exceed 50°C (122°F).
- Do not give the tool a shock by dropping, striking, etc.
- Do not expose the light to eyes continuously. It may hurt them.
- Do not cover or clog the lit tool with cloth or carton, etc. It may create a risk of fire.
- Switch off the light immediately when the lamp gets dark in use. If you leave the lamp switched on, the battery cartridge capacity may decrease.
- If any problem develops, consult your nearest Service Center or dealer. To maintain product safety and reliability, repairs, maintenance or adjustment should be carried out by Authorized Service Center.
SAVE THESE INSTRUCTIONS
FUNCTIONAL DESCRIPTION CHARGING
Charge the battery cartridge with the matched charger before use.
INSTALLING OR REMOVING BATTERY CARTRIDGE
- Always switch off the tool before insertion or removal of the battery cartridge.
- To remove the battery cartridge, withdraw it from the tool while sliding the button on the front of the cartridge.
- To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
- Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.
LIGHTING UP THE BULB (FIG. 2)
CAUTION:
- Do not look in the light or see the source of light directly.
- This tool has function that bulb light goes out at low voltage.
HEAD ANGLE (FIG. 2)
The head angle can be adjusted in four stages. Adjust as desired.
ASSEMBLY REPLACING BULB
(FIG. 3 & 4)
CAUTION:
The bulb is very hot immediately after operation. Wait until the bulb cools
off before attempting to replace it.
First, turn the ring counterclockwise and remove the reflector. Then replace
the bulb.
MAINTENANCE
To maintain product safety and reliability, repairs, maintenance or adjustment should be carried out by a Authorized Service Center.
ACCESSORIES
CAUTION:
These accessories or attachments are recommended for use with your Makita tool
specified in this manual.
The use of any other accessories or attachments might present a risk of injury
to persons.
The accessories or attachments should be used only in the proper and intended
manner.
- Belt hook
- genuine batteries and chargers
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>