AOC 16T10 15.6 Inch LCD Monitor User Manual

: September 10, 2024
: AOC

Table of Contents

16T10 15.6 Inch LCD Monitor
Specifications:
Product Usage Instructions:
Safety:
- FAQ:
Q: What should I do if the monitor emits a strange smell or
Q: Can I use strong detergent to clean the monitor

16T10 15.6 Inch LCD Monitor

“`html

Specifications:

Model: 16T10
Manufacturer: AOC
Power Input: 100-240V AC, Min. 5A
Screen Type: LCD
Recommended Ventilation Space: 4 inches (10cm) around the
monitor

Product Usage Instructions:

Safety:

1. Power:

Operate the monitor only from the indicated power source.
Unplug during lightning storms or long periods of non-use.
Ensure the wall socket is easily accessible and grounded.

2. Installation:

Avoid placing the monitor on unstable surfaces to prevent
injury or damage.
Use recommended mounting accessories and follow manufacturer’s
instructions.
Ensure proper air circulation and ventilation around the
monitor.
If wall-mounting, use an approved mounting kit and follow the
instructions.

3. Cleaning:

Clean the cabinet regularly with a soft cloth and mild
detergent.
Avoid spilling liquids on the monitor and ensure no detergent
enters the product.
Disconnect the power cord before cleaning.

4. Other:

If abnormal smells, sounds, or smoke are detected, disconnect
the power immediately and seek service.
Avoid blocking ventilating openings and exposing the monitor to
severe vibration or impact.
Avoid knocking or dropping the monitor during operation or
transportation.

FAQ:

Q: What should I do if the monitor emits a strange smell or

sound?

A: Immediately disconnect the power plug and contact a Service
Center for assistance.

Q: Can I use strong detergent to clean the monitor

cabinet?

A: No, only use soft-detergent to wipe out stains and avoid
cauterizing the product cabinet.

“`

LCD Monitor User Manual
16T10

www.aoc.com

®

Safety …………………………………………………………………………………………………………………………………………………………….. 1 National Conventions ……………………………………………………………………………………………………………………………… 1 Power …………………………………………………………………………………………………………………………………………………… 2 Installation …………………………………………………………………………………………………………………………………………….. 3 Cleaning ……………………………………………………………………………………………………………………………………………….. 4 Other ……………………………………………………………………………………………………………………………………………………. 5
Setup ……………………………………………………………………………………………………………………………………………………………… 6 Contents in Box……………………………………………………………………………………………………………………………………… 6 Setup Stand & Base……………………………………………………………………………………………………………………………….. 7 Adjusting Viewing Angle………………………………………………………………………………………………………………………….. 8 Connecting the Monitor …………………………………………………………………………………………………………………………… 9 Wall Mounting………………………………………………………………………………………………………………………………………. 10
Adjusting……………………………………………………………………………………………………………………………………………………….. 11 Hotkeys ………………………………………………………………………………………………………………………………………………. 11 OSD Setting ………………………………………………………………………………………………………………………………………… 12 Luminance ………………………………………………………………………………………………………………………………… 13 Color Setup……………………………………………………………………………………………………………………………….. 14 Picture Boost …………………………………………………………………………………………………………………………….. 15 OSD Setup………………………………………………………………………………………………………………………………… 16 Game Setting…………………………………………………………………………………………………………………………….. 17 Extra ………………………………………………………………………………………………………………………………………… 18 Exit…………………………………………………………………………………………………………………………………………… 19 LED Indicator ………………………………………………………………………………………………………………………………………. 20
Troubleshoot………………………………………………………………………………………………………………………………………………….. 21 ………………………………………………………………………………………………………………………………………………….. 22 ……………………………………………………………………………………………………………………………. 22
Preset Display Modes …………………………………………………………………………………………………………………………… 23 Pin Assignments…………………………………………………………………………………………………………………………………… 24 Plug and Play ………………………………………………………………………………………………………………………………………. 25
i

Safety
National Conventions
The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings warning is mandated by regulatory authority.
1

Power
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges. receptacles marked between 100-240V AC, Min. 5A.
The wall socket shall be installed near the equipment and shall be easily accessible.
2

Installation
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.
shock. Never spill liquids on the monitor.

If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence

To avoid potential damage, for example the panel peeling from the bezel, ensure that the monitor does not tilt downward by more than -5 degrees. If the -5 degree downward tilt angle maximum is exceeded, the monitor damage will not be covered under warranty.
See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the stand:

Installed with stand

12 inches 30cm

4 inches 10cm

4 inches 10cm
Leave at lease this space around the set

4 inches 10cm

3

Cleaning
Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
Please disconnect the power cord before cleaning the product.
4

Other
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation. Do not knock or drop the monitor during operation or transportation.
5

Setup
Contents in Box

Monitor

QSG

Flip Cover

Warranty card

Power Adapter CP0154-0503000UA1

USB A-C Cable

HDMI Cable

USB C Cable

Not all signal cables will be provided for all countries and regions. Please check with the local dealer or AOC branch

6

Setup Stand & Base
Please setup or remove the base following the steps as below. Setup: Remove:
7

Adjusting Viewing Angle
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor as below:
NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
Warning · To avoid potential screen damage, such as panel peeling, ensure that the monitor does no t tilt downward by more
than -5 degrees. · Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.
8

Connecting the Monitor

1. HDMI 2. USB C 3. Earphone

Mini HDMI

USB C

Connect to PC
1. Connect the power adaptor to the back of the display firmly 2. Turn off your computer and unplug its power cable. 3. Connect the display signal cable to the video connector on the back of your computer. 4. Plug the power cord of your computer and the power adaptor of your display into a nearby outlet. 5. Turn on your computer and display. If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting.

9

Wall Mounting
Preparing to Install An Optional Wall Mounting Arm.

75mm M4

X2 Wall Mounting: M4*(4+X)mm (X=Thickness of Wall mount bracket)
M=4.0Max

D3.86-3.94

Dk=8.0

H=2.0

M4-P0.7 L=4+X

This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1. Follow the manufacturer’s instructions to assemble the wall mounting arm. 2. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the
monitor. 3. Insert the 2 screws into the holes and tighten. 4. Reconnect the cables. Refer to the user’s manual that came with the optional wall mounting arm for instructions on
attaching it to the wall.
Noted: Always contact manufacturer for wall-mount installation.(For models with wall mount)

WARNING: 1. To avoid potential screen damage, such as panel peeling, ensure that the monitor does not tilt downward by more than
-5 degrees. 2. Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.
10

Adjusting
Hotkeys
1 Source/Exit 2 Volume 3 Game Mode 4 Menu/Enter 5 Power Menu/Enter Power Press the Power button to turn on the monitor. Volume When there is no OSD, press ” “” key to open Volume function,then press ” ” or ” ” key to select Volume. Game Mode When there is no OSD, press ” ” key to open game mode function, then press ” ” or ” ” key to select game mode (FPS, Source/Exit When the OSD is closed, press Source/Exit button will be Source hot key function.
12

OSD Setting
Basic and simple instruction on the control keys.

Luminance

Color Setup

Picture Boost

OSD Setup

Game Setting

Extra

Exit

Contrast Brightness Eco mode

50 90 Standard

Gamma DCR HDR Mode

Gamma1 Off Off

1). Press the

MENU-button to activate the OSD window.

2). Press Up or Down to navigate through the functions. Once the desired function is highlighted, press the

MENU-button to activate it, press Up or Down to navigate through the sub-menu functions. Once the desired

function is highlighted, press

MENU-button to activate it.

3). Press Up or Down to change the settings of the selected function. Press function, repeat steps 2-3.

to exit. If you want to adjust any other

Notes:
1). If the product has only one signal input, the item of “Input Select” is disable to adjust. 2). If the product input signal resolution is the local resolution, the “Image Ratio” item is invalid. 3). ECO modes (except Standard mode), DCR, DCB mode and Picture Boost, for these four states that only one state
can exist. 4). OSD lock, long press the ” ” button for 10 seconds to lock or unlock the menu.

13

Luminance

Color Setup

Picture Boost

OSD Setup

Game Setting

Extra

Exit

Contrast Brightness Eco mode

50 90 Standard

Gamma DCR HDR Mode

Gamma1 Off Off

Contrast Brightness Eco mode
Gamma

0-100 0-100 Standard Text Internet Game Movie Sports Reading Gamma1 Gamma2 Gamma3

DCR On

HDR Mode
Note: When ” HDR Mode”

HDR Picture HDR Movie HDR Game

Contrast from Digital-register. Backlight Adjustment. Standard Mode. Text Mode. Internet Mode. Game Mode. Movie Mode. Sports Mode. Reading Mode. Adjust to Gamma 1. Adjust to Gamma 2. Adjust to Gamma 3. Disable dynamic contrast ratio. Enable dynamic contrast ratio.
Optimized for the color and contrast of the picture,
Gamma” cannot be adjusted.

14

Color Setup

Color Setup
Color Temp. DCB Mode DCB Demo

Picture Boost Warm Off Off

OSD Setup
Red Green Blue

Game Setting

Extra
50 50 50

Exit

Luminance

Color Temp.
DCB Mode
DCB Demo Red Green Blue

Warm Normal Cool User sRGB
Full Enhance Nature Skin Green Field Sky-blue Auto Detect
0-100 0-100 0-100

Recall Warm Color Temperature from EEPROM. Recall Normal Color Temperature from EEPROM. Recall Cool Color Temperature from EEPROM. Restore Color Temperature from EEPROM.
Retrieve sRGB Color Temperature from EEPROM. Disable DCB Mode. Enable Full Enhance Mode. Enable Nature Skin Mode. Enable Green Field Mode. Enable Sky- blue Mode. Enable AutoDetect Mode. Disable or Enable Demo. Red gain from Digital-register. Green gain from Digital-register. Blue gain from Digital- register.

Note: When “Color Setup” under “HDR Mode” is set to

, “Color Setup” items cannot be adjusted.

15

Picture Boost

OSD Setup

Game Setting

Extra

Exit

Luminance

Color Setup

Bright Frame

Off

Brightness

50

H. Position

0

Frame Size

14

Contrast

50

V. Position

0

Bright Frame Frame Size Brightness Contrast H. position V. position

14-100 0-100 0-100 0-100 0-100

Disable or Enable Bright Frame. Adjust Frame Size. Adjust Frame Brightness. Adjust Frame Contrast. Adjust Frame horizontal Position. Adjust Frame vertical Position.

Note: Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience. When “HDR Mode”

16

OSD Setup

OSD Setup Language Timeout

Game Setting

Extra

Exit

English 10

H. Position V. Position

Luminance

Color Setup

Picture Boost

50

Transparence

25

0

Break Reminder

Off

Language
Timeout H. Position V. Position Transparence Break Reminder

English Français Français Português Deutsch Italiano Nederlands Svenska Suomi Polski Cestina Türkçe 5-120 0-100 0-100 0-100

Select the OSD language.
Adjust the OSD Timeout. Adjust the horizontal position of OSD. Adjust the vertical position of OSD. Adjust the transparence of OSD. Break reminder if the user continuously work for more than 1hrs.

17

Game Setting

Game Setting Game Mode Shadow Control

Extra Off
50

Exit

Luminance

Overdrive

Off

Game Color

Color Setup

Picture Boost

LowBlue Mode

10

DialPoint

OSD Setup Off Off

Game Mode

FPS RTS Racing Gamer 1 Gamer 2 Gamer 3

Shadow Control 0-100

Game Color

0-20

No optimization by Smart image game
Improves dark theme black level details. For playing RTS (Real Time Strategy). Improves the image quality. For playing Racing games, Provides fastest response time and high color saturation. User’s preference settings saved as Gamer 1.
User’s preference settings saved as Gamer 2.
User’s preference settings saved as Gamer 3. Shadow Control Default is 50, then end-user can adjust from 50 to 100 or 0 to increase contrast for clear picture. 1. If picture is too dark to be saw the detail clearly,
adjusting from 50 to100 for clear picture. 2. If picture is too white to be saw the detail clearly,
adjusting from 50 to0 for clear picture Game Color will provide 0-20 level for adjusting saturation to get better picture.

Overdrive
LowBlue Mode DialPoint

Weak Medium

Adjust the response time.

Strong

off/Multimedia/ Network/Office/Reading
on off

Reduce blue light waves by controlling Color Temp. Turn on or off the game DialPoint.

Note:
When “Color Setup” under “HDR Mode” is set to Mode” items cannot be adjusted.

, “Game Mode”, “Shadow Control”, “Game Color””Low Blue

18

Extra

Extra Input Select Off Timer Image Ratio

Exit

Luminance

Auto 00 Wide

Color Setup DDC/CI Reset

Picture Boost Yes No

OSD Setup

Game Setting

Resolution : 1920(H)x1080(V) H. Frequency : 68 KHz

V. Frequency : 60 Hz

Input Select
Image Ratio DDC/CI Reset

Auto/HDMI/USB C1/USB C2 0-24hrs Wide / 4:3 Yes or No Yes or No

Select Input Signal Source.
Select image ratio for Display. y
Turn ON/OFF DDC/CI Support. Reset the menu to default.

19

Exit

Luminance

Color Setup

Picture Boost

OSD Setup

Game Setting

Extra

Exit

Exit the main OSD

20

LED Indicator
Status Full Power Mode

LED Color White Orange

21

Troubleshoot

Problem & Question Power LED Is Not ON
No images on the screen

Possible Solutions
Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor.
Is the power cord connected properly? Check the power cord connection and power supply. Is the cable connected correctly? (Connected using the VGA cable) Check the VGA cable connection. (Connected using the HDMI cable) Check the HDMI cable connection. (Connected using the DP cable) Check the DP cable connection. * VGA/HDMI/DP input is not available on every model. If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows 7/8/10) and then change the frequency of the video card. (Refer to the Setting the Optimal Resolution) If the initial screen (the login screen) does not appear, contact the Service Center or your dealer. Can you see “Input Not Supported” on the screen? You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. Make sure the AOC Monitor Drivers are installed.

Picture Is Fuzzy & Has Ghosting Shadowing Problem
Picture Bounces, Flickers Or Wave Pattern Appears In The Picture

Adjust the Contrast and Brightness Controls. Press to auto adjust. Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back.
Move electrical devices that may cause electrical interference as far away from the monitor as possible. Use the maximum refresh rate your monitor is capable of at the resolution you are using. The Computer Power Switch should be in the ON position.

Mode”
Missing one of the primary colors (RED, GREEN, or BLUE) Screen image is not centered or sized properly Picture has color defects (white does not look white)

Make sure the monitor’s video cable is properly connected to the computer. Inspect the monitor’s video cable and make sure no pin is bent. Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.
Inspect the monitor’s video cable and make sure that no pin is damaged. Make sure the monitor’s video cable is properly connected to the computer.
Adjust H-Position and V-Position or press hot-key (AUTO).
Adjust RGB color or select desired color temperature.

Horizontal or vertical disturbances on the screen

Use Windows 7/8/10 shut-down mode to adjust CLOCK and FOCUS. Press to auto- adjust.

Regulation & Service

Please refer to Regulation & Service Information which is in the CD manual Regulation & Service Information in Support page.

22

Specification

General Specification

Model Name

16T10

Panel

Driving System Viewable Image Size

TFT Color LCD 39.5cm diagonal(15.6” Wide Screen)

Pixel Pitch

0.17925mm(H) x 0.17925mm(V)

Horizontal Scan Range

30k-85kHz

Horizontal Scan Size(Maximum) 344.16mm

Vertical Scan Range

48-75Hz

Vertical Scan Size(Maximum) 193.59mm

Max Resolution

1920×1080@60Hz

Plug & Play

VESA DDC2B/CI

Others

External Power Supply Model CP0154-0503000UA1

Power Source

5.0V 3.0A

Power Consumption

Typical (default brightness and contrast) Max. (brightness =100, contrast =100)

10W 15W

Standby mode

0.5W

Dimensions

354.2×222.4×9.6mm(WxHxD)

Net Weight

1.1kg

Physical

Connector Type

Characteristics Signal Cable Type

Mini HDMI/USB C Detachable

Temperature

Operating Non-Operating

0°C~40°C -25°C~55°C

Environmental Humidity

Operating Non-Operating

10%~85%(non-condensing) 5%~93%(non-condensing)

Altitude

Operating Non-Operating

0m~5000m(0ft~16404ft) 0m~12192m(0ft~40000ft)

23

Preset Display Modes

STANDARD VGA SVGA
XGA SXGA WSXG
WXGA+ WSXGA+
FHD

RESOLUTION 640×480@60Hz 800×600@56Hz 800×600@60Hz 1024×768@60Hz 1280×1024@60Hz 1280×720@60Hz 1280×960@60Hz 1440×900@60Hz 1680×1050@60Hz 1920×1080@60Hz

HORIZONTAL FREQUENCY(KHz)
31.469 35.156 37.879 48.363 63.981 45.000 60.000 55.935 65.290 67.500

VERTICAL FREQUENCY(Hz)
59.940 56.250 60.317 60.004 60.020 60.000 60.000 59.887 59.954 60.000

24

Pin Assignments

Pin No. Signal Name

TMDS Data 2+

TMDS Data 2 Shield

TMDS Data 2-

TMDS Data 1+

TMDS Data 1Shield

TMDS Data 1-

TMDS Data 0+

TMDS Data 0 Shield

Pin No. Signal Name

TMDS Data 0-

17. DDC/CEC Ground

10. TMDS Clock +

18. +5V Power

TMDS Clock Shield

19. Hot Plug Detect

12. TMDS Clock-

13. CEC

14. Reserved (N.C. on device)

15. SCL

16. SDA

20-Pin Color Display Signal Cable

Pin No. 1 2 3 4 5 6 7 8 9 10

Signal Name ML_Lane 3 (n) GND ML_Lane 3 (p) ML_Lane 2 (n) GND ML_Lane 2 (p) ML_Lane 1 (n) GND ML_Lane 1 (p) ML_Lane 0 (n)

Pin No. 11 12 13 14 15 16 17 18 19 20

Signal Name GND ML_Lane 0 (p) CONFIG1 CONFIG2 AUX_CH(p) GND AUX_CH(n) Hot Plug Detect Return DP_PWR DP_PWR

25

Plug and Play
Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.
26