Cuisinart SS-7 Series Single Serve Coffeemaker Instruction Manual

September 11, 2024
Cuisinart

Cuisinart SS-7 Series Single Serve Coffeemaker Instruction Manual

SS-7 Series

For your safety and continued enjoyment of this product, always read the instruction book carefully before using.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be taken to reduce the risk of fire, electric shock, and/or injury to persons, including the following:

  1. READ ALL INSTRUCTIONS.

  2. Do not touch hot surfaces. Use handles and knobs.

  3. To protect against fire, electric shock, and injury to persons, do not place cord, plug, or base unit in water or other liquids.

  4. Close supervision is necessary when any appliance is used by or near children or individuals with certain disabilities.

  5. Always unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts and before cleaning the appliance.

  6. Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or has been dropped or damaged in any manner.
    Return appliance to the nearest Cuisinart Repair Center for examination, repair, or electrical or mechanical adjustment.

  7. The use of accessory attachments not recommended by Cuisinart may cause injuries, fire, electric shock, or other injury to persons.

  8. Do not use outdoors.

  9. Do not let cord hang over edge of table or counter, or touch hot surfaces.

  10. Do not place on or near a hot gas or electric burner, or in a heated oven.

  11. Always fill water reservoir first, then plug cord into the wall outlet. To disconnect, turn control to Off, then remove plug from wall outlet.

  12. Scalding may occur if the water filter compartment cover is removed during the brewing cycle.

  13. Do not use appliance for other than its intended use.

  14. Do not lift handle to open the lid of the brewer while brewing is in progress.

  15. Do not overfill the water reservoir with water. Use only water in this appliance!
    Do not put any other liquids or foods in the water reservoir except as instructed in the cleaning instructions in this guide.

  16. Do not clean drip tray with cleansers, steel wool pads, or other abrasive materials.

  17. WARNING: To reduce the risk of fire or electric shock, do not remove the base panel. No user-serviceable parts are inside. Repair should be done only by authorized personnel.

  18. Do not operate your appliance in an appliance garage or under a wall cabinet. When storing in an appliance garage, always unplug the unit from the electrical outlet. Not doing so could create a risk of fire, especially if the appliance touches the walls of the garage or the door touches the unit as it closes.

SAVE THESE INSTRUCTIONS

FOR HOUSEHOLD USE ONLY
WARNING: RISK OF FIRE OR ELECTRIC SHOCK

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated, dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of fire or electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

SPECIAL CORD
SET INSTRUCTIONS
A short power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord.
Longer extension cords are available and may be used if care is exercised in their use.
If a longer extension cord is used, the marked electrical rating of the extension cord must be at least as great as the electrical rating of the appliance, and the longer cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over

NOTICE
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.

IMPORTANT UNPACKING INSTRUCTIONS

  1. Place the box on a large, sturdy, flat surface.
  2. Remove the instruction booket and any other literature.
  3. Turn the box so that the back side of the brewer is down and slide the brewer from the box.
  4. After removing the brewer, place the box out of the way and take the side pulp-molded inserts away.
  5. Remove the polybag covering the brewer. We suggest you save all packing materials in the event that future shipping of the machine is needed. Keep all plastic bags away from children.

THE QUEST FOR THE
PERFECT CUP OF COFFEE

Element 1: Water
Coffee is 98% water. The quality of that water is as important as the quality of your coffee. If water doesn’t taste good from the tap, it won’t taste good in your coffee.

Element 2: Coffee
The flavour of your beverage comes from the coffee, tea, cocoa — or whatever you’re brewing. To achieve the best taste, always use the best ingredients. Select fresh, high-quality beans or ground coffee, and only the best single- serve capsules.

Element 3: Grind
The grind of coffee or the refinement of tea leaves is critical for proper flavour extraction. Pre-ground ingredients in top-quality single-serve capsules ensure excellent, flavorful results. When using pre-ground coffee to brew using the HomeBarista® Reusable Filter Cup, the grind is just as critical. If it’s too fine, over-extraction will result in bitterness and may clog the filter. If too coarse, maximum flavor is not extracted. We recommend a medium-fine grind.

Element 4: Proportion
No matter which cup size you choose, the Cuisinart Soho™ Single-Serve Coffeemaker, working in conjunction with a single-serve capsule, will always produce the perfect cup every time.

When grinding your own coffee and using it in a reusable coffee capsule (not included), remember to add the amount of ground coffee that corresponds to the number of ounces being brewed.

FEATURES AND BENEFITS

  1. Brewer Handle

  2. Brew Head/Brewing Chamber holds Removable Capsule holder or reusable coffee capsule (not included).

  3. BREW/CANCEL Button with LED Indicator

  4. Removable Capsule Holder

  5. Removable Drip Tray Plate

  6. Drip Tray
    Two-position drip tray to accommodate different-sized mugs. Removes from base to accommodate standard-sized travel mug, up to 20-oz.

  7. Drip Tray Base

  8. Reservoir Lid

  9. Water Reservoir

  10. Water Reservoir Markings
    Use to fill reservoir based on desired cup size or brew strength.

  11. Power Cord with Integrated Storage (not shown)

  12. Automatic Shutoff (not shown)
    As a safety feature, your brewer will automatically shut off when it is idle for longer than 30 minutes. Press the BREW/CANCEL button to restart.

SETTING UP YOUR BREWER

Initial Cleaning
Perform an initial cleaning before making your first beverage. Follow these instructions, without inserting a capsule.

  1. Remove water reservoir lid from the unit.
  2. Fill the reservoir with 12 oz. of water.

3. Plug the power cord into an independent outlet.
4. Open and close the brew head. Do not add a capsule.
5. Place mug on the drip tray.
6. Press the BREW/
CANCEL button. The LED indicator will start breathing and hot water will dispense into the cup.
7. The one-time cleaning process is complete. Discard hot water.
Your brewer is ready to use.

BREWING
1. Remove water reservoir lid.
2. Add water to the reservoir. Use the water level markings to fill to the desired amount or strength you want to brew. Replace lid.

3. Plug cord into an electrical outlet. The BREW/CANCEL LED indicator will flash.
4. Place mug on the drip tray.

Note: Adjust positioning of the mug depending on size and the selected brew amount. Two-position drip tray can be moved up to accommodate shorter mugs, and the drip tray can be removed to accommodate most travel mugs.

5. Select a capsule.
Note: Do not remove the foil lid or puncture the capsule.
6. Open the brew head and place a capsule in the brewing chamber. Make sure to press the capsule down completely in place.
Caution: There are two sharp needles in the brewing chamber that puncture the capsule, one above and one below. To avoid risk of injury, do not put your fingers in the capsule brewing chamber.

7. Close the brew head.
Once the brew head is closed, the BREW/ CANCEL LED indicator will remain solid, indicating the unit is ready.
8. Press the BREW/CANCEL button to begin brewing. The beverage will start to dispense momentarily. The BREW/
CANCEL LED indicator will breathe slowly during the brewing cycle.

Note: To cancel brewing, simply press the BREW/CANCEL button and the brewing process will stop.

Caution: There is very hot water in the capsule chamber during the brewing process. To avoid risk of injury, do not lift the handle or open the capsule chamber during the brewing process.

9. Once the beverage is fully dispensed, all lights will go off. Lift the brewer handle, then remove and dispose of the used capsule. Close the brew head.
Caution: Capsule will be hot.
10. Enjoy your cup of coffee! Your brewer is ready to use again.

CLEANING AND MAINTENANCE

Cleaning External Parts

We recommend regular cleaning of the coffeemaker’s external components.

  1. Never immerse the coffeemaker in water or other liquids. The housing and other external components may be cleaned with a soapy, damp, nonabrasive cloth.
  2. To remove the drip tray, simply lift it toward you, keeping it level at all times in order to prevent spills. The drip tray and drip-tray plate are dishwasher safe. Do not clean the drip tray with cleansers, steel wool pads, or other abrasive materials.

CLEANING THE CAPSULE HOLDER

Caution: There are sharp needles that puncture the capsule above and below.
To avoid risk of injury, do not put your fingers in the capsule brewing chamber.

  1. The capsule holder is top-shelf dishwasher safe (use a low-temperature cycle). To remove, lift the handle to open the brewing chamber. Grasp the top of the capsule holder and pull up.
  2. Cleaning the funnel
    To remove the funnel from the capsule holder, grip the funnel with your left hand, twist the bottom away from you slightly, and pull away from the capsule holder to remove. The funnel is top-rack dishwasher safe.
    Note: The funnel may be tight the first few times you remove it; this is normal and will loosen with continued use.

3. Cleaning the exit needle
The exit needle is located on the inside bottom of the capsule holder assembly.
Should a clog arise because of coffee grounds, it can be cleared using a paper clip or similar tool. Remove the capsule holder from the unit, then remove the funnel from the capsule holder and insert the paper clip into the exit needle to loosen the clog and push it out.

Replace the funnel onto the capsule holder by lining up the tabs in the funnel with the

notches on the capsule holder, and then twist toward you until the funnel locks into place. After cleaning, replace the capsule holder, being sure to align the arrow on the capsule holder rim with the arrow on the brewing chamber.
4. Cleaning the piercing needle
The piercing needle is located on the inside of the brewing chamber. Should a clog arise because of coffee grounds, it can be using a paper clip or similar tool.
Insert the paper clip to loosen the clog and push it out.

CLEANING THE WATER RESERVOIR
It is normal over time for discoloration, spotting, or staining to appear in the water reservoir. Results will vary depending on the mineral content of the water used, but will not affect the operation of the brewer. However, be sure to clean the water reservoir regularly to minimize buildup.

Clean inside the water reservoir with a damp, lint-free cloth as necessary.

MAINTENANCE

Any other servicing should be performed by an authorized service representative.

DESCALING YOUR BREWER
Mineral content in water varies from place to place. Depending on the mineral content of the water in your area, calcium deposits or scale may build up in your brewer. Though scale is nontoxic, it can hinder brewer performance.

Descaling your brewer will help maintain the heating element and other parts that come in contact with water.

For optimal performance, descale your brewer every 3 to 6 months. It is possible for calcium deposits to build up faster, making it necessary to descale more often. When the BREW/ CANCEL LED indicator flashes quickly 3 times upon turning the unit on, this indicates the need to descale.

To begin, you will need the following:

  • 24 ounces (680 g) of distilled white vinegar
  • 12-ounce (340 g) ceramic mug (do not use paper cup)
  • Access to a sink

Step 1: First Vinegar Rinse

  • Fill water reservoir with 12 ounces (340 g) of undiluted white vinegar.
  • Place the ceramic mug on the drip tray.
  • Lift the brewer handle, but do not add a coffee capsule.
  • Close the brew head, and press and hold BREW/CANCEL for 5 seconds to start the cleaning cycle.
  • During the cleaning cycle, the LED indicator will flash until the cycle is complete.
  • Once the vinegar is dispensed, discard it into sink.

Step 2: Second Vinegar Rinse

  • Repeat step 1.

Step 3: Fresh Water Rinse

  • Repeat step 1 three times using fresh water in place of vinegar.
  • This will clean the brewer plumbing and remove any residual vinegar taste.

The brewer is now ready for normal use.

TROUBLESHOOTING

WARRANTY

LIMITED THREE-YEAR WARRANTY

We warrant that this Cuisinart product will be free of defects in materials or workmanship under normal home use for 3 years from the date of original purchase. This warranty covers manufacturer’s defects including mechanical and electrical defects. It does not cover damage from consumer abuse, unauthorized repairs or modifications, theft, misuse, or damage due to transportation or environmental conditions. Products with removed or altered identification numbers will not be covered.

This warranty is not available to retailers or other commercial purchasers or owners. If your Cuisinart product should prove to be defective within the warranty period, we will repair it or replace it if necessary. For warranty purposes, please register your product online at www. cuisinart.ca to facilitate verification of the date of original purchase and keep your original receipt for the duration of the limited warranty.

This warranty excludes damage caused by accident, misuse or abuse, including damage caused by overheating, and it does not apply to scratches, stains, discolouration or other damage to external or internal surfaces that does not impair the functional utility of the product. This warranty also expressly excludes all incidental or consequential damages.

Your Cuisinart product has been manufactured to the strictest specifications and has been designed for use only in 120 volt outlets and only with authorized accessories and replacement parts. This warranty expressly excludes any defects or damages caused by attempted use of this unit with a converter, as well as use with accessories, replacement parts or repair service other than those authorized by Cuisinart.

If the appliance should become defective within the warranty period, do not return the appliance to the store. Please contact our Customer Service Centre:

Toll-free phone number:
1-800-472-7606
Address:
Cuisinart Canada
100 Conair Parkway, Unit #1,
Woodbridge, ON L4H 0L2
Email:
consumer_Canada@conair.com
Model:
SS-7 SERIES
To facilitate the speed and accuracy of your return, please enclose:
• $10.00 for shipping and handling of the product (cheque or money order)
• Return address and phone number
• Description of the product defect
• Product date code*/copy of original proof of purchase
• Any other information pertinent to the product’s return

  • The date code format we are using on unit is WWYY, representing week, and year. eg.2424
    = manufactured in 24th week of the year 2024.

Note: We recommend you use a traceable, insured delivery service for added protection.
Cuisinart will not be held responsible for in-transit damage or for packages that are not delivered to us.

To order replacement parts or accessories, call our Customer Service Centre at 1-800-472- 7606. For more information, please visit our website at www.cuisinart.ca.

©2024 Cuisinart Canada
100 Conair Parkway, Unit #1, Woodbridge, ON L4H 0L2
Printed in China | 24CC091486

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals