FORNO FMWDR3093-24BLK,FMWDR3093-24WHT Built-In 1.6 cu.ft. Microwave Oven Installation Guide

: September 6, 2024
: FORNO

FORNO FMWDR3093-24BLK,FMWDR3093-24WHT Built-In 1.6 cu.ft. Microwave Oven Installation Guide

Safety Definitions

WARNING
This indicates that death or serious injuries may occur as a result of non- observance of this warning.

CAUTION
This indicates that minor or moderate injuries may occur as a result of non- observance of this warning.

NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory

Note: This alerts you to important information and/or tips.

**** IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE AFTER INSTALLATION IS COMPLETE. IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR’S USE.

WARNING
If the information in this manual is not followed exactly, fire or shock may result causing property damage or personal injury.
WARNING
Do not repair, replace or remove any part of the appliance unless specifically recommended in the manuals. Improper installation, service or maintenance can cause injury or property damage. Refer to this manual for guidance. All other servicing should be done by an authorized servicer.

Appliance Handling Safety

Unit is heavy and requires at least two people or proper equipment to move. Do not lift appliance by door handle. Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance.

Safety Codes and Standards

This appliance complies with the latest version of one or more of the following standards:
CAN/CSA C22.2 No. 61 – Household Cooking Ranges
UL 858 Household Electric Ranges
CAN/CSA C22.2 No. 150 – Microwave Ovens
UL 923 – Microwave Cooking Appliances
UL 507 Electric Fans
CAN/CSA C22.2 No. 113 Fans and Ventilators
CSA C22.2 No. 64 Household Cooking and Liquid- Heating Appliances
UL 1026-Electric Household Cooking and Food Serving Appliances

It is the responsibility of the owner and the installer to determine if additional requirements and/or standards apply to specific installations.

Electric Safety

WARNING
Before you plug in an electrical cord or turn on power supply, make sure all controls are in the OFF position.

For appliances equipped with a cord and plug, do not cut or remove the ground prong. It must be plugged into a matching grounding type receptacle to avoid electrical shock. If there is any doubt as to whether the wall receptacle is properly grounded, the customer should have it checked by a qualified electrician. If required by the National Electrical Code (or Canadian Electrical Code), this appliance must be installed on a separate branch circuit. Installer – show the owner the location of the circuit breaker or fuse. Mark it for easy reference. Before installing, turn power OFF at the service panel. Lock service panel to prevent power from being turned ON accidentally.
Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections and grounding must comply with all applicable codes.

Microwave Safety
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

Do not operate or allow the oven to be operated with the door open.
Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary:
1. Interlock operation
2. Proper door closing
3. Seal and sealing surfaces (arcing, wear, and other damage)
4. Damage to or loosening of hinges and latches
5. Evidence of dropping or abuse
Before turning on microwave power for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connection.
Any damaged or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.
A microwave leakage check to verify compliance with the Federal Performance Standard should be performed on each oven prior to release to the owner.

GROUNDING INSTRUCTIONS

This appliance must be grounded. Grounding reduces the risk of electric shock by providing a safe pathway for electric current in the event of a short circuit. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

WARNING
Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance.

Remove all tape and packaging before using the appliance. Destroy the packaging after unpacking the appliance. Never allow children to play with packaging material. Never modify or alter the construction of the appliance. For example, do not remove leveling legs, panels, wire covers or anti-tip brackets/screws.

WARNING
To reduce the risk of fire, use only metal ductwork.

CAUTION
For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

Proposition 65 Warning:
This product may contain a chemical known to the State of California, which can cause cancer or reproductive harm. Therefore, the packaging of your product may bear the following label as required by California:

STATE OF CALIFORNIA PROPOSITION 65 WARNING:
WARNING
Cancer and Reproductive Harm www.P65Warnings.ca.gov

Before you begin

Tools and parts needed

Philips head screwdriver
1/8″ drill bit and drill
Measuring tape

Parts included

Microwave oven
Philips head screws

Power Requirements
The outlet must be properly grounded in accordance with all applicable codes. It can be installed in the back wall directly behind the appliance. You can also connect your appliance directly to a compatible conventional Built-in Oven. Refer to separate Combination Instructions.

Checklist for Installation

Use this checklist to verify that you have completed each step of the installation process. This can help you avoid mistakes. Refer to detailed instructions for each step in the sections following this checklist

Before installing the appliance, be sure to verify the cabinet dimensions are correct for your appliance and that the required electrical connections are present. Make sure the electrical conduit provided on the appliance is able to reach to the point of connection. Section: Dimensions and Cabinet Requirements
Move the appliance into place in front of the cabinet opening. Section: Removing Packaging
Remove packaging materials, leaving the bottom packaging on the appliance to avoid damage to the floor. Section: Removing Packaging
Team-lift the appliance directly into the cabinet cutout. Section: Install Appliance, “Mount to Cabinet
Slide the appliance all the way into place. Section: Install Appliance, “Mount to Cabinet”
Fasten the appliance to the cabinet opening with the screws supplied. Section: Install Appliance, “Mount to Cabinet”

Always read and follow the complete installation instructions contained in this manual.

Removing Packaging

_ NOTICE: _To prevent damage to your floor keep the unit in its packaging base until ready to be placed in the cabinet opening. Do not slide the unit across the flooring. Different models use different packaging materials. Bracket remains in packaging base.

Cut straps on outside of box.
Remove cardboard box.
Remove all top and side cardboard and Styrofoam braces.
Place oven in front of cabinets where it is to be installed.

_ NOTICE: _To avoid damage to the microwave oven, do not grip or use the door or door handle while the microwave oven is being handled.

Dimensions and Cabinet Requirements

General Cabinet Requirements

% (6.4 mm) space between the side of the appliance and an adjacent wall or cabinet door when installed at the end of a cabinet run.
The cabinet base must be fiat and capable of supporting the weight of your appliance when in use. See section Cabinet Dimensions.
The appliance door will overlap the furniture below by approx 3/16″ (5 mm) when opened.

WARNING
There must be an air gap of at least ]” (6 mm) between the appliance and the cabinet walls when the appliance is installed, ie. X” (3 mm) each side

Outlet Area

The outlet can be located anywhere within the shaded area. Anywhere within the shaded area, the minimal distance between the appliance and the wall is 1% in (45 mm).
Outlet Area

Appliance Dimensions

Cabinet Dimensions

Cabinet Dimension

_ NOTICE: _The cabinet base must be flat and capable of supporting a weight of at least 142 lbs (64.1 kg).

**Under counter dimensions

**

**Flush installation

baseplate e” (8)
measurements in inches (mm)
**

Flush installation also requires:

two side cleats to be attached inside the cabinet frame, recessed from the front
a” (8 mm) baseplate underneath the unit body.

Electrical Installation

The model stated on the front cover is rated at 120VAC AC, 60 Hz and uses a NEMA 5-20 plug to connect to a dedicated 120VAC microwave circuit.

Model	Connection	Circuit Requirements
FMWDR3093-24BLK FMWDR3093-24WHT	ΝΕΜΑ 5-20	120 VAC, 20 Amps 60 Hz

Electrical Requirements:
a three prong grounded outlet
120 VAC, 60 Hz, only
20 Amp electrical supply with a fuse or a circuit breaker

This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electric Code or the prevailing local code for this rating. The power supply cord and plug should be brought to a separate 20-amp branch circuit single grounded outlet. The outlet box should be located inside the cabinet above the appliance (see section Location Requirements). The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code.
The voltage used must be the same as specified on this microwave oven. Using a higher voltage is dangerous and may result in a fire or oven damage. Using a lower voltage will cause slow cooking. The manufacturer is not responsible for any damages resulting from the use of the oven with any voltage other than specified.

Install Appliance

Note: The appliance is heavy. It is advisable to install it with a second person.
NOTICE : Before installing the appliance, be sure to verify the cabinet dimensions and electrical connections.

Mount to Cabinet

Fully insert the appliance and center it. Do not kink the electrical cable.
Screw the appliance into place.

Testing Operation

Turn on power at the breaker.
Test the oven mode: Select the mode. See the Use and Care Manual for detailed operation instructions.
Verify that the oven light comes on and the oven begins to preheat.
. Test the microwave: Place a cup of water into the oven cavity, Follow The instructions in the Use and Care Manual on how to heat a beverage.
Verify that the oven light comes on and the water is heated
If any of the tests do not result as explained above, contact Service for assistance. Otherwise, the installation is complete at this time.

Before Calling Service
See the Use and Care Manual for troubleshooting information. Refer to the “Statement of Limited Product Warranty in the Use and Care Manual. To reach a service representative, see the contact information at the front of the manual or in the following section. Please be prepared with the information printed on your product data plate prior to calling

Data Plate
The data plate shows the model and serial number. Refer to the data plate on the appliance when requesting service. The data plate can be found on the inside of the appliance door.

Data Plate
To avoid having to search for each piece of information when calling, you can enter the four items needed in the spaces provided below.