SOLBREEZE SS BIG DOG Dock and Boat Dog Ladder Installation Guide

: September 7, 2024
: SOLBREEZE

Table of Contents

SS BIG DOG Dock and Boat Dog Ladder
Product Information
Specifications:
Product Usage Instructions:

SS BIG DOG Dock and Boat Dog Ladder

Product Information

Specifications:

Spacing Bar: Included
L Brackets (E): Included
Anchor Bolt (A): Included
Knurled Knob: Included
Anti-Slip Plate (B): Included
Spring Washer (C): Included
Hex Nut (D): Included
Drill Bit Size: 1/2 for pilot hole, 7/8 for anchor bolt
hole

Product Usage Instructions:

Step By Step Instructions:

Attach the spacing bar to the L brackets (E).
Position the assembled L brackets onto the mounting surface
ensuring space for anti-slip plates, locking washers, and nuts on
the rear side.

Hold the L brackets under the surface to verify hole
locations.
Place L brackets back on top of the mounting surface.
Mark initial anchoring position with a 1/2 pilot hole using the
L bracket as a template.
Temporarily remove the holder and bore a 7/8 hole for the
anchor bolt.
Insert the Anchor Bolt (A) through the hole.
Fasten the L bracket to the anchor bolt with a knurled
knob.
Place the Anti-Slip Plate (B) with teeth facing up on the back
side.
Add the Spring Washer (C) followed by the Hex Nut (D).
Secure tightly.
Repeat marking, drilling, and securing each hole individually
three more times.

FAQ

Q: Do I need any additional tools for installation?

A: The product comes with all necessary components for
installation. However, you may need a drill for creating pilot and
anchor bolt holes.

Q: Can this product be used outdoors?

A: The product can be used outdoors but ensure proper
weatherproofing measures are taken to prevent rust and
corrosion.

Installing the SOLBREEZE Dog Ladder (A) Anchor Bolt, 7/8″-9 outside, 1/2″-13 inside, L=2.75″ 304 Stainless Steel (B) An -Slip Plate, 4 ½” x 2 ¼” inches, 304 Stainless Steel (C) Spring Washer, 304 Stainless Steel (D) Hex Nut, 304 Stainless Steel (33 mm drive socket) (E) L-Brackets with Spacing Bar
Video Link of install: h ps://youtu.be/dXhu8usiXrE?si=YmRWeliqCylNi-WU

Step By Step Instruc ons
1. A ach the spacing bar to the L brackets (E). 2. Posi on the assembled L brackets onto the moun ng surface. Ensure there
is enough space for the an -slip plates, locking washers, and nuts to be placed on the rear side of the surface.
o It helps to hold the L brackets under the surface you will mount to, verifying that nothing obstructs where the holes are located on the L brackets.
o Once verified, place the L brackets back onto the top of the moun ng surface.
3. Mark the ini al anchoring posi on with a 1/2″ pilot hole. Use the L bracket as a template and drill directly through the hole on the L bracket with a 1/2″ drill bit.
4. Temporarily remove the holder, then bore a 7/8″ hole to accommodate the anchor bolt.
5. Insert the Anchor Bolt (A) through the hole. 6. Fasten the L bracket to the anchor bolt with a knurled knob. 7. Place the An -Slip Plate (B) on the back side, with the teeth facing up. 8. Then add the Spring Washer (C). 9. Follow with the Hex Nut (D). 10.Secure ghtly. 11.Repeat this sequence three more mes, marking and drilling each hole one
at a me, ensuring each hole is marked, drilled, and secured individually.