LECTROTAB JLC-11 Joystick LED Trim Tab Control Instruction Manual

: June 13, 2024
: LECTROTAB

Table of Contents

LECTROTAB JLC-11 Joystick LED Trim Tab Control
Product Information
Product Usage Instructions
FEATURES
PRELIMINARY SPECIFICATIONS
JLC-11 WIRING and DIMENSIONS
JLC-11 Programming Chart
8 LED each side = Auto Retract Disabled
8 LED each side = Tabs operate independently
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LECTROTAB JLC-11 Joystick LED Trim Tab Control

Product Information

The JLC-11 Joystick LED Trim Tab Control by Lectrotab is a user-friendly control designed to enhance the boating experience. It incorporates features requested by boat owners to provide precise control over trim tab movement.

Key Features:

Single or dual station control
1 or 2 actuator per trim tab
Black color
Overall width: 3.0″ (77mm)
Overall height/thickness: 3.0″ (77mm) / 2.0″ (50mm)
Mounting hole DC cutout diameter: 2.625″ (66.7mm)
Voltage: 12/24VDC
Fuse size: 12VDC = 15 or 20 amps, 24VDC = 10 amps

For more information about the JLC-11 Joystick LED Trim Tab Control, please visit the Lectrotab website or contact them at Ph: 804-368-8428 or Email: sales@lectrotab.com.

Product Usage Instructions

To program the JLC-11 Joystick LED Trim Tab Control, follow these steps:

Lectrotab’s Joystick LED control incorporates features requested by boat owners to provide a user-friendly control for a more enjoyable boating experience.

Single “Joystick” control
NMEA 2000 compatible
LED display of each trim tab position

FEATURES

Microprocessor based trim tab control with LED tab position indicators
NMEA 2000 compatible with JLC-NMEA adapter
Move both tabs up or down simultaneously with a single motion
Dual station ready – just add a second JLC-11 and JR-* cable (sold separately)
Automatic return to last tab position if ignition key is turned off and back on again
Completely sealed, completely waterproof and will not deteriorate in sunlight• Automatic tab retraction and calibration with key or accessory switch off
Easy upgrade from any of our Lectrotab controls
No external power module required
LED tab position indicators dim automatically in darkness and brighten in sunlight
Single or Dual Actuator per tab
Operates on 12 or 24 volt dc systems

PRELIMINARY SPECIFICATIONS

Model Number

|

Display Color

|

Number of Stations/Actuators

|

Overall Width

| Overall Height/ Thickness|

Mounting Hole Cutout (Diameter)

|

DC

Voltage

| Fuse Size Power Input

(1 Actuator per Tab)

| Fuse Size Aux. (MUST

CONNECT)

---|---|---|---|---|---|---|---|---

JLC-11

|

Black

| Single or Dual Station/

1 or 2 Actuator/tab

|

3.0″/

77mm

|

3.0“(77mm)/

2.0”(50mm)

|

2.625″/66.7mm

|

12/24

| 12vdc = 15 or 20 amps

24vdc = 10amps

|

1 to 2 amp

Linear Devices Corporation
11126 Air Park Road, Suite G, Ashland, VA 23005
www.lectrotab.com, Ph 804-368-8428, Email: sales@lectrotab.com
August 2023

JLC-11 WIRING and DIMENSIONS

“ILC-11” Control Installation/ Wiring Diagram

JLC-11 Programming Chart

4 LEDs = 4 second actuator

Remember Last Tab

Position

|

Pull & hold joystick back

| Move and hold Joystick Up or Down| Push joystick right and hold 4 seconds +|

Standard/Remember

|

Standard

| 8 LEDs each side = Standard Retract

1 LED each side = Remember Last Tab Position

Swap LED’s

|

Push & hold joystick right

|

Move and hold Joystick Up or Down

|

Push joystick right and hold 4 seconds +

| LEDs match tab movement or opposite tab movement|

LEDs match tab movement direction

| 1 LED on right and left = LEDs follow and match tab movement direction

8 LEDs on right and left = LED follow opposite of

tab movement direction

Disable Auto Tab Retract| Push & hold joystick forward| Move and hold Joystick Up or Down| Push joystick right and hold 4 seconds +|

Enable/Disable

|

Enabled

| #1 LED each side = Default of Auto Tab Retract enabled

8 LED each side = Auto Retract Disabled

Independent Tab Control

| Push & hold joystick 45° towards upper left

position (between top and left position)

|

Move and hold Joystick Up or Down

|

Push joystick right and hold 4 seconds +

|

Enable/Disable

|

Disabled

| #1 LED each side = Default Disabled or tabs do not operate independently

8 LED each side = Tabs operate independently

|

Programming Details

Timing: #LEDs lit corresponds to the #seconds in actuator stroke time i.e. 8 LEDs = 8 seconds, 4 LEDs = 4 seconds (Actuator’s A and B series = 8 seconds, C and D series = 4 seconds and S series = 6 seconds)
Rember Last Tab Position: If AUX power is switched from +12 or 24vdc to 0vdc, tabs retract (Set Timing + 1 sec.). When power is reapplied, tabs go to last position before key sw. off. Removing +12 or 24vdc power source will reset original setting back to fully retracted and keep fully retracted at new power sorce on. (8 LEDs on each side = standard auto retract and no last setting, 1 top LED on each side = remember last tab position before Aux power off.)
Swap LED’s: 1 LED on right and left side = LEDs follow and match tab direction, 8 LEDs on right and left side = LEDs follow opposite of tab direction
Disable Auto Tab Retract: Note this program mode does not require +12vdc to the AUX terminal. Press the All Up and All Down buttons at same time for 2sec Press the STBD Bow Down/Up to adjust between Enable and Disable. (#1 LED each side = Default of Auto Tab Retract enabled. #8 LED each side = Auto Retract Disabled) Press the Port Bow Up to exit program and save setting.
Independent Tab Control: 1 LED on right and left side = Tabs do not operate independently, 8 LEDs on right and left side = Independent control of each tab

Linear Devices Corporation