PIOCREAT G5ULTRA 3D Printer User Manual

: September 6, 2024
: PIOCREAT

Table of Contents

G5ULTRA 3D Printer
Specifications:
Product Usage Instructions:
1. Download and Install Software:
2. Model Management:
3. Consumables Management:
4. Model Slicing:
5. Off-line Print:
6. Start Printing:
7. Operation Guide:
- FAQ:
Q: Can I print files from subfolders on the U disk?
Q: What should I do if I encounter issues during printing?

G5ULTRA 3D Printer

Specifications:

Brand: Piocreat
Model: 3D Printer
Official Website: www.piocreat3d.com
Supports: Nozzle diameter selection, G-code generation, Offline
printing

Product Usage Instructions:

1. Download and Install Software:

Download the software from the official website or find it on
the storage card for installation.
Double click to open the software.
In the settings, select the corresponding WiFi connection.
Open Piocreat_Print and load the file. Select the file for
printing.

2. Model Management:

Add a new printer by selecting the printer and nozzle diameter,
then click to add the printer.
Manage the printer settings by entering the configuration
interface and adjusting related configurations.

3. Consumables Management:

Add materials by entering the material list, selecting
materials, and clicking next.
Manage materials by entering the configuration interface and
adjusting related configurations.

4. Model Slicing:

Import a model and click to slice for G-code preview.

5. Off-line Print:

Generate G-code and save the file to a U disk. Insert the U
disk for printing.
Refer to the slicing software manual on the U disk for detailed
instructions.
Avoid inserting or removing the U disk during printing to
prevent issues.

6. Start Printing:

After selecting a file, start printing and adjust parameters in
real-time.

7. Operation Guide:

The operation guide provides information about temperature
settings, model preview, Z-axis offset, print time, and control
options.

FAQ:

Q: Can I print files from subfolders on the U disk?

A: No, saved files can only be copied to the root directory of
the U disk, not to subfolders.

Q: What should I do if I encounter issues during printing?

A: Refer to the troubleshooting section in the user manual for
assistance in resolving common problems.

11. Download and install software

1 Download the software from official website(www.piocreat3d.com) or find the software in storage card for installation. (www.szcx3d.com) U

3 Select languageSelect your machine Select nozzle diameter Finish.

2 Double click to open the software. |
Open the Settings, select the corresponding WiFi connection.

4 Open Piocreat_Print LoadRead file) Select file.

3

4 Piocreat Load
18

11. Model management
1 Add new printer Select your printer Select nozzle diameter Click to add printer. 2 Click to manage Enter the configuration interface Adjust related configurations.

19

11. Model management
1 2

20

11. Consumables management
1 Click to add Enter the Material list Select your Materials Next. 2 Click to manage Enter the configuration interface Adjust related configurations.

21

11. Consumables management
1 2

22

11. Consumables management
3 Import Parameter config. | 4 Configure your parameters. |
EN CN

23

11. Model Slicing
1 Import model Click to slice G-code preview. 2 G-code

EN CN

24

11. Off-line print

3 Generate G-codeand save the gcode file to U disk. G U
The file name supports both Chinese and English, numbers, and common symbols (the length of the file name is limited to 20 characters). 20

4 Insert the U disk U
Notes: 1For details on the software instructions, please refer to the slicing software manual in the U disk. 2Saved files can only be copied to the root directory of the U disk, not to subfolders. 1U 2U

Warning: Please don’t insert or remove the U disk during printing. U

25

11. Start Printing
After selecting a file to start printing, you can adjust printing related parameters in real time.
EN CN
26

11. Start Printing
After starting printing, you can observe the printing status and adjust printing related parameters in real time.
EN CN
27

11. Operation guide

Print interface
Nozzle upper section temperature
Nozzle lower section temperature
Heating bed temperature

Model preview

Z-axis offset downward Z

Z-axis offset upward Z

Print time
Heating bed temperature Nozzle temperature Adjustment Pause Stop Start

Increase printing speed
Slow down printing speed

Increase extrusion flow
Reduce extrusion flow Fan speed

Setting interface

Note: The interface is for reference only :

Start

Adjustment

Z-axis offset upward Z

Z-axis offset downward Z

Pause

Fan speed

Increase printing speed

Slow down printing speed

Stop

Increase extrusion flow

Reduce extrusion flow
28

13.Troubleshooting
29

13.Troubleshooting

30

14.Maintainance
Linear slide maintenance: When the machine is in use for about 3 months, the linear slide block needs to be supplemented with lubricating grease once. The grease can be injected into the slider with the aid of a grease gun from the grease nipple attached to the slider. Lubricating grease is suitable for occasions where the speed does not exceed 60m/min and there is no requirement for cooling. It is recommended that customers use lubricating oil with an oil viscosity of about 32-150cst to lubricate the linear slides; 3 60m/min,32-150cst Screw maintenanceWhen the machine is in use for about 3 months, the screw needs to be supplemented with lubricating grease once. You can use ordinary brushes or tools that can lift grease. The lubricating grease is suitable for occasions where the speed does not exceed 60m/min and there is no requirement for cooling. It is recommended that customers use lithium soap grease with a dropping point not lower than 258. 360m/min, 258
31

15.After-Sales Service Card

Scan the code to know more

Please read the user manual and warranty card carefully before the use. For any service, Please priorly contact local seller or contact us via Email: after@piocreat 3d.com for support. See www.piocreat3d.com / for specific warranty information about your product and procedures to act on a warranty claim.
32

(U) 7

33

SD

9:00 20:30

9:00 18:30

0755-2103-9743

after@piocreat3d.com

34

Notes

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. -This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Shenzhen Piocreat 3D Technology Co., Ltd.

Scan To Learn More

Shenzhen Piocreat 3D Technology Co., Ltd.
Add: Room 1308, Building No. 3, Jincheng Industrial Area, Tongsheng Community, Dalang Street, Longhua District, Shenzhen, China, 518109 Tel: +86 0755-2103 9743 Official Website: www.piocreat3d.com E-mail: after@piocreat3d.com hello@piocreat3d.com
1308 0755-2103 9743 www.szcx3d.com