ZEBRA MC945x Handheld Mobile Computer User Guide
- August 31, 2024
- ZEBRA
Table of Contents
- MC945x Handheld Mobile Computer
- Product Information
- Specifications:
- Regulatory Compliance:
- Charging Precautions:
- Regulatory Markings:
- Health and Safety Recommendations:
- Vehicle Installation:
- Safety Guidelines:
- Restricted Use Locations:
- Safety in Hospitals and Aircraft:
- RF Exposure Guidelines:
- Q: Can I charge the device with non-Zebra accessories?
- Q: Where can I find regulatory markings on the device?
MC945x Handheld Mobile Computer
“`html
Product Information
Specifications:
- Manufacturer: Zebra Technologies Corporation
- Compliance: UL Listed
- Model Numbers: All Zebra devices
Product Usage Instructions
Regulatory Compliance:
Ensure the device is used in compliance with all rules and
regulations in the location of use. Use only Zebra approved and UL
Listed mobile devices, battery packs, and accessories.
Charging Precautions:
Only charge with Zebra approved and NRTL-certified accessories.
Do not attempt to charge damp or wet devices. Ensure all components
are dry before connecting to a power source.
Regulatory Markings:
Refer to the Declaration of Conformity (DoC) for details on
regulatory markings. Access regulatory marks specific to the device
through Settings > Regulatory on the device screen.
Health and Safety Recommendations:
Follow ergonomic workplace practices to minimize injury risks.
Consult with your Health and Safety Manager for guidance.
Vehicle Installation:
Ensure proper installation to avoid RF signal interference in
vehicles. Position the device within easy reach without causing
driver distractions.
Safety Guidelines:
Obey laws on wireless device use while driving. Avoid
distractions and prioritize safety on the road.
Restricted Use Locations:
Adhere to restrictions and instructions in areas where
electronic devices are restricted.
Safety in Hospitals and Aircraft:
Switch off wireless devices when requested in hospitals,
clinics, and aircraft to prevent interference with sensitive
equipment.
RF Exposure Guidelines:
Operate the device as per supplied instructions. Compliance with
international standards for human exposure to electromagnetic
fields is ensured.
Frequently Asked Questions (FAQ)
Q: Can I charge the device with non-Zebra accessories?
A: No, only use Zebra approved and NRTL-certified accessories
for charging.
Q: Where can I find regulatory markings on the device?
A: Access regulatory marks specific to the device through
Settings > Regulatory on the device screen.
“`
MC945x Regulatory Guide
Regulatory Information
This device is approved under Zebra Technologies Corporation.
This guide applies to the following model numbers:
· MC945A
· MC945B
All Zebra devices are designed to be compliant with the rules and regulations
in the locations they are sold and will be labeled as required.
Local language translation / (BG) / (CZ) Peklad do místního jazyka / (DE)
Übersetzung in die Landessprache / (EL) / (ES) Traducción de idiomas locales /
(ET) Kohaliku keele tõlge / (FI) Paikallinen käännös / (FR) Traduction en
langue locale / (HR) Prijevod na lokalni jezik / (HU) Helyi nyelv fordítás /
(IT) Traduzione in lingua locale / (JA) / (LT) Vietins kalbos vertimas / (LV)
Tulkojums vietj valod / (NL) Vertaling in lokale taal / (PL) Tlumaczenie na
jzyk lokalny / (PT) Tradução do idioma local / (RO) Traducere în limba local /
(RU) / (SK) Preklad do miestneho jazyka / (SL) Prevajanje v lokalni jezik /
(SR) / (SV) Översättning av lokalt språk / (TR) Yerel dil çevirisi / (ZH-CN) /
(ZH-TW) / zebra.com/support
Any changes or modifications to Zebra equipment not expressly approved by
Zebra could void the user’s authority to operate the equipment.
Declared maximum operating temperature: 50°C
For use only with Zebra approved and UL Listed mobile devices, Zebra approved,
and UL Listed/Recognized battery packs.
CAUTION: Only use Zebra approved and NRTL-certified accessories, battery
packs, and battery chargers. Do NOT attempt to charge damp/wet mobile
computers, printers or batteries. All components must be dry before connecting
to an external power source.
Bluetooth® Wireless Technology
This is an approved Bluetooth® product. For more information on the Bluetooth
SIG listing, please visit bluetooth.com.
Regulatory Markings
Regulatory markings subject to certification are applied to the device
signifying the radio(s) is/are approved for use. Refer to the Declaration of
Conformity (DoC) for details of other country markings. The DOC is available
at: zebra.com/doc.
The regulatory marks specific to this device (including FCC and ISED) are
available on the screen of the device by following these instructions:
Go to Settings > Regulatory.
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. © 2022 Zebra Technologies Corp. and/or its affiliates. All rights reserved. | zebra.com
partnumber-xxEN
Health and Safety Recommendations
Ergonomic Recommendations
In order to avoid or minimize the potential risk of ergonomic injury, always
follow good ergonomic workplace practices. Consult with your local Health and
Safety Manager to ensure that you are adhering to your company’s safety
programs to prevent employee injury.
Vehicle Installation
RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles (including safety systems). Check with the
manufacturer or its representative regarding your vehicle. Ensure the
equipment is installed to avoid driver distractions. You should also consult
the manufacturer about any equipment that has been added to your vehicle.
Position the device within easy reach. User should be able to access the
device without removing their eyes from the road.
IMPORTANT: Before installing or using, check national and local laws regarding
distracted driving.
Safety on the Road
Give your full attention to driving. Obey the laws and regulations on the use
of wireless devices in the areas where you drive. The wireless industry
reminds you to use your device / phone safely when driving.
Restricted Use Locations
Remember to observe restrictions and obey all signs and instructions on the
use of electronic devices in restricted use locations.
Safety in Hospitals and Aircraft
Wireless devices transmit radio frequency energy that may affect medical
electrical equipment and aircraft’s operation. Wireless devices should be
switched off wherever you are requested to do so in hospitals, clinics,
healthcare facilities or by airline staff. These requests are designed to
prevent possible interference with sensitive equipments.
RF Exposure Guidelines
Safety Information
Reducing RF Exposure Use Properly
Only operate the device in accordance with the instructions supplied. The
device complies with internationally recognized standards covering human
exposure to electromagnetic fields. For information on international human
exposure to electromagnetic fields, refer to the Zebra Declaration of
Conformity (DoC) at zebra.com/doc.
2
Use only Zebra tested and approved headset, belt-clips, holsters, and similar
accessories to ensure RF exposure compliance. If applicable, follow the
instructions for use as detailed in the accessory guide. The use of third-
party belt clips, holsters, and similar accessories may not comply with RF
exposure compliance requirements and should be avoided. For further
information on the safety of RF energy from wireless devices, refer to RF
exposure and assessment standards section at zebra.com/responsibility. To
satisfy RF exposure requirements, this device must operate with a minimum
separation distance of xxxx cm or more from a user’s body and nearby persons.
To satisfy RF exposure requirements, this device must be hand-held only and,
where applicable use only with Zebra tested and approved accessories.
Optical Devices
Laser
Class 2 laser scanners use a low power, visible light diode. As with any very
bright light source such as the sun, the user should avoid staring directly
into the light beam. Momentary exposure to a Class 2 laser is not known to be
harmful.
CAUTION: Use of controls, adjustments, or the performance of procedures other
than those specified in the supplied product documentation may result in
hazardous laser light exposure.
SE4770 SE5800
Wavelength: 630-680 nm Maximum output: 1 mW Pulse duration: 12.5 ms Beam divergence: 42.7 ° Repetition rate: 16.9 ms Wavelength: 500-570 nm Maximum output: 2 mW Pulse duration: 4 ms Beam divergence: 42 ° Repetition rate: 16.7 ms
3
Scanner Labeling
SE4770
LASER LIGHT – DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT. LUMIÉRE LASER –
NE PAS REGARDER DANS LE FAISCEAU. APPAREIL À LASER DE CLASSE 2. 630-680 nm 1mW
12.5ms
2
COMPLIES WITH 21 CFR1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO
LASER NOTICE NO. 56, DATED MAY 08, 2019 AND IEC/EN 60825-1:2014. 2,
SE5800
LASER LIGHT – DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT. LUMIÉRE LASER –
NE PAS REGARDER DANS LE FAISCEAU. APPAREIL À LASER DE CLASSE 2. 500-570 nm 2mW
4ms
2
COMPLIES WITH 21 CFR1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO
LASER NOTICE NO. 56, DATED MAY 08, 2019 AND IEC/EN 60825-1:2014. 2,
LED
Labels read:
1. Laser Light — do not stare into beam. Class 2 Laser product. 630-680
nm,1mW (applied to SE4770)
1. Laser Light — do not stare into beam. Class 2 Laser product. 500-570 nm,
2mW (applied to ZE5800)
2. Complies with 21 CFR1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 56, dated May 08, 2019 and IEC/EN 60825-1:2014.
CAUTION: Laser light emitted from this aperture.
Risk Group classified according to IEC 62471:2006 and EN62471:2008. · SE4770
Pulse Duration: 17.7 ms Exempt Group (RG0)
· SE5800 Pulse Duration: 6 ms Exempt Group (RG0)
4
Power Supply
WARNING ELECTRICAL SHOCK: Use only a Zebra approved, Certified ITE LPS power
supply with appropriate electrical ratings. Use of alternative power supply
will invalidate any approvals given to this unit and may be dangerous.
Batteries and Power Packs
This information applies to Zebra-approved batteries and power packs
containing batteries.
Battery Information
CAUTION: Risk of explosion if battery is replaced by an incorrect type.
Dispose of batteries according to instructions. Use only Zebra approved
batteries. Accessories which have battery charging capability are approved for
use with the following battery models: · Model BT-000370 (3.6 VDC, 7000 mAh) ·
Model BT-000371 (3.6 VDC, 5000 mAh) Zebra approved rechargeable battery packs
are designed and constructed to the highest standards within the industry.
However, there are limitations as to how long a battery can operate or be
stored before needing replacement. Many factors affect the actual life cycle
of a battery pack such as heat, cold, harsh environmental conditions, and
severe drops. When batteries are stored over six months, some irreversible
deterioration in overall battery quality may occur. Store batteries at half
charge in a dry, cool place, removed from the equipment to prevent loss of
capacity, rusting of metallic parts, and electrolyte leakage. When storing
batteries for one year or longer, the charge level should be verified at least
once a year and charged to half charge. Replace the battery when a significant
loss of run time is detected. · Standard warranty period for all Zebra
batteries is one year, regardless if the battery was purchased separately or
included as part of the host device. For more information on Zebra batteries,
please visit: zebra.com/batterydocumentation and select the Battery Best
Practices link.
Battery Safety Guidelines
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
WARNING When using this product basic safety precautions should always be
followed, including the following: The area in which the units are charged
should be clear of debris and combustible materials or chemicals. Particular
care should be taken where the device is charged in a non-commercial
environment. · Read all the instructions before using the product. · Follow
battery usage, storage, and charging guidelines found in the user’s guide. ·
Improper battery use may result in a fire, explosion, or other hazard. ·
Batteries subjected to extremely low air pressure may result in an explosion
or the leakage of flammable liquid or gas. · To charge the mobile device
battery, the battery and charger temperatures must be between 0°C and 40°C
(32°F and 104°F).
5
· Do not use incompatible batteries and chargers. Use of an incompatible
battery or charger may present a risk of fire, explosion, leakage, or other
hazard. If you have any questions about the compatibility of a battery or a
charger, contact Zebra support.
· Do not disassemble or open, crush, bend or deform, puncture, or shred.
Damaged or modified batteries may exhibit unpredictable behavior resulting in
fire, explosion, or risk of injury.
· Severe impact from dropping any battery-operated device on a hard surface
could cause the battery to overheat.
· Do not short circuit a battery or allow metallic or conductive objects to
contact the battery terminals. · Do not modify, disassemble, or remanufacture,
attempt to insert foreign objects into the battery,
immerse or expose to water, rain, snow or other liquids, or expose to fire,
explosion, or other hazard. · Do not leave or store the equipment in or near
areas that might get very hot, such as in a parked vehicle
or near a radiator or other heat source. Do not place battery into a microwave
oven or dryer. · To reduce the risk of injury, close supervision is necessary
when used near children. · Please follow local regulations to promptly dispose
of used re-chargeable batteries. · Do not dispose of batteries in fire.
Exposure to temperatures over 100°C (212°F) may cause explosion. · Seek
medical advice immediately if a battery has been swallowed. · In the event of
a battery leak, do not allow the liquid to come in contact with the skin or
eyes. If contact
has been made, wash the affected area with large amounts of water and seek
medical advice. · If you suspect damage to your equipment or battery, contact
Zebra support to arrange for inspection.
Marking and European Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with
Directives 2014/53/EU and 2011/65/EU. Any radio operation limitations within
EEA countries are identified in Appendix A of EU Declaration of Conformity.
The full text of the EU Declaration of Conformity is available at:
zebra.com/doc. EU Importer : Zebra Technologies B.V Address: Mercurius 12,
8448 GX Heerenveen, Netherlands
Waste Electrical and Electronic Equipment (WEEE)
For EU and UK Customers: For products at the end of their life, please refer
to recycling/disposal advice at: zebra.com/weee.
6
United States and Canada Regulatory
Radio Frequency Interference Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules.These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help. Operation
of transmitters in the 5.925-7.125 GHz band is prohibited for control of or
communications with unmanned aircraft systems.
Radio Frequency Interference Requirements Canada
Innovation, Science and Economic Development Canada ICES-003 Compliance Label:
CAN ICES-003 (B)/NMB-003(B) This device complies with Innovation, Science and
Economic Development Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause interference; and (2)
This device must accept any interference, including interference that may
cause undesired operation of the device. L’émetteur/récepteur exempt de
licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes
: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de
l’appareil doit accepter tout brouillage radio électrique subi même si le
brouillage est susceptible d’en compromettre le fonctionnement.
This device is restricted to indoor use when operating in the 5150 to 5350 MHz
frequency range. Lorsqu’il fonctionne dans la plage de fréquences 5 150- 5350
MHz, cet appareil doit être utilisé exclusivement en extérieur. Operation of
transmitters in the 5.925-7.125 GHz band is prohibited for control of or
communications with unmanned aircraft systems. L’utilisation d’émetteurs dans
la bande 5,925-7,125 GHz est interdite pour la commande de systèmes d’aéronefs
sans pilote ou pour les communications avec ces systèmes. Devices shall not be
used for control of or communications with unmanned aircraft systems. Les
dispositifs ne doivent pas être utilisés pour commander des systems d’aéronef
sans pilote ni pour communiquer avec de tels systèmes.
7
RF Exposure Requirements – FCC and ISED
The FCC has granted an Equipment Authorization for this device with all
reported SAR levels evaluated in compliance with the FCC RF emission
guidelines. SAR information on this device is on file with the FCC and can be
found under the Display Grant section of www.fcc.gov/oet/ea/fccid.
To satisfy RF exposure requirements, this device must operate with a minimum
separation distance of 1 cm or more from a user’s body and nearby persons.
Pour satisfaire aux exigences d’exposition aux radio fréquences, cet appareil
doit fonctionner avec une distance de séparation minimale de 1 cm ou plus de
corps d’une personne.
To satisfy RF exposure requirements, this device must be hand-held only and,
where applicable use only with Zebra tested and approved accessories.
Pour être conforme à la réglementation relative à l’exposition RF, cet
appareil doit être uniquement porté au poignet ou à la cheville et, lorsque
cela est applicable, utilisé uniquement avec des accessoires testés et
approuvés par Zebra.
Hotspot Mode
To satisfy RF exposure requirements in hotspot mode, this device must operate
with a minimum separation distance of 1.0 cm or more from a user’s body and
nearby persons.
Pour satisfaire aux exigences d’exposition RF en mode hotspot, cet appareil
doit fonctionner avec une distance de séparation minimale de 1,0 cm ou plus du
corps de l’utilisateur et des personnes à proximité.
Co-located Statement
To comply with FCC RF exposure compliance requirement, the antenna used for
this transmitter must not be co-located (within 20 cm) or operating in
conjunction with any other transmitter/antenna except those already approved
in this filling.
Hotspot ISED Notice
When operating in hotspot mode, this device is restricted to indoor use when
operating in the 5150 – 5350 MHz frequency range.
En mode de connexion partagée (hotspot), l’utilisation de cet appareil doit se
faire exclusivement en extérieur lorsqu’il fonctionne dans la plage de
fréquences 5 150 – 5 350 MHz.
UL Listed Products with GPS
Underwriters Laboratories Inc. (UL) has not tested the performance or
reliability of the Global Positioning System (GPS) hardware, operating
software, or other aspects of this product. UL has only tested for fire,
shock, or casualties as outlined in UL’s Standard(s) for Safety for
Information Technology Equipment. UL Certification does not cover the
performance or reliability of the GPS hardware and GPS operating software. UL
makes no representations, warranties, or certifications whatsoever regarding
the performance or reliability of any GPS related functions of this product.
Marquage UL des produits équipés d’un GPS
Les tests menés par Underwriters Laboratories Inc. (UL) ne portent ni sur les
performances, ni sur la fiabilité du matériel et du logiciel d’exploitation du
GPS (Global Positioning System), ni sur tout autre aspect de ce produit. UL a
uniquement testé la résistance au feu, aux chocs et aux sinistres, comme le
définit la norme UL60950-1 relative à la sécurité des matériels de traitement
de l’information. La certification UL ne couvre ni les performances, ni la
fiabilité du matériel et du logiciel d’exploitation GPS. UL ne formule aucune
déclaration, ni ne délivre aucune garantie ni aucun certificat concernant les
performances et la fiabilité des fonctions GPS de ce produit.
8
Hazardous Locations
Class 1 Div 2 Product Regulatory Information
This Equipment is suitable for use in Class I, Division 2, Groups A, B, C, D;
Class II, Division 2, Groups F, and G; Class III, or Non-Hazardous Locations
only.
WARNING – EXPLOSION HAZARD: Substitution of components may impair suitability
for Class I and II, Division 2, and Class III.
WARNING – EXPLOSION HAZARD: Do not disconnect equipment unless power has been
switched off or the area is known to be non-hazardous.
WARNING – EXPLOSION HAZARD: BATTERIES MUST ONLY BE CHANGED IN AN AREA FREE OF
IGNITIBLE CONCENTRATIONS. Use with battery model BT-000370, manufactured by
TWS Technology (Guangzhou) Limited.
WARNING – EXPLOSION HAZARD: Docking port NOT FOR USE in hazardous locations.
CAUTION: Risk of Explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
WARNING – EXPLOSION HAZARD: DO NOT REMOVE OR REPLACE while circuit is live
unless the area is free of ignitible concentrations.
Informations réglementaires sur les produits de classe 1, division 2
Cet équipement peut être utilisé uniquement dans la classe I, division 2,
groupes A, B, C et D, la classe II, division 2, groupes F et G, la classe III
ou les emplacements non dangereux.
AVERTISSEMENT – RISQUE D’EXPLOSION : La substitution de composants peut nuire
à l’adéquation aux classes I et II, division 2 et classe III.
AVERTISSEMENT – RISQUE D’EXPLOSION : Ne pas déconnecter l’équipement à moins
que l’alimentation n’ait été coupée ou que la zone ne soit pas dangereuse.
AVERTISSEMENT – RISQUE D’EXPLOSION : LES PILES NE DOIVENT ÊTRE CHANGÉES QUE
DANS UNE ZONE EXEMPTE DE CONCENTRATIONS INFLAMMABLES. À utiliser avec le
modèle de pile BT-000370, fabriqué par TWS Technology (Guangzhou) Limited.
AVERTISSEMENT – RISQUE D’EXPLOSION : Le port d’accueil n’est pas destiné à
être utilisé dans des endroits dangereux.
ATTENTION : Risque d’explosion si la pile est remplacée par une pile de type
incorrect. Éliminez les piles usagées conformément aux instructions.
AVERTISSEMENT – RISQUE D’EXPLOSION : NE PAS ENLEVER OU REMPLACER lorsque le
circuit est sous tension, sauf si la zone est exempte de concentrations
inflammables.
Brasil
Este equipamento não tem direito à proteção contra interferência prejudicial e
não pode causar interferência em sistemas devidamente autorizados.
Este produto está homologado pela Anatel de acordo com os procedimentos
regulamentados para avaliação da conformidade de produtos para
telecomunicações e atende aos requisitos técnicos aplicáveis, incluindo os
limites da medida da exposição humana referente a campos elétricos, magnéticos
e eletromagnéticos de radiofrequência
9
Colombia
Señor usuario, la siguiente información se entrega de conformidad con lo
establecido en el Régimen de protección de los derechos de los usuarios,
expedido por la Comisión de Regulación de Comunicaciones.
Recomendaciones de uso:
1. Utilice siempre que pueda dispositivos manos libres.
2. Evite utilizar el equipo mientras conduce un vehículo.
3. En caso que el teléfono sea utilizado por niños, ancianos, mujeres
embarazadas y población inmunocomprometida, consulte a su médico y el manual
del equipo.
4. Si usted utiliza algún dispositivo electrónico de uso médico, asegúrese
que el mismo esté protegido contra las ondas de radiofrecuencia externas.
5. Apague su teléfono en lugares tales como: hospitales, centros de salud,
aviones, estaciones de suministro de combustible, en presencia de gases
explosivos y lugares donde se realizan explosiones.
6. Evite que terceros hagan uso de su teléfono para prevenir la implantación
de dispositivos como programas espías (spyware) o identificadores ocultos, que
atentan contra la seguridad de la información contenida en el mismo.
France
Cet appareil a été testé et déclaré conforme aux limites applicables
d’exposition aux radiofréquences (RF).
Le débit d’absorption spécifique (DAS) local quantifie l’exposition de
l’utilisateur aux ondes électromagnétiques de l’équipement concerné.
Les valeurs SAR les plus élevées sont disponibles sur la déclaration de
conformité (DoC) disponible sur: www.zebra.com/doc
México
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.
MC945B MPE 1.0 mW/cm², ____ mW/cm²
10
/ 9 13 (EPA) 15
5.15 5.35 GHz
(Product Description in CHINESE
Equipment name)
Unit
(Pb)
Model Type designation (Type)
Restricted substances and its chemical symbols
(Hg)
(Cd)
(Cr+6)
(PBB)
(PBDE)
—
1. 0.1 wt % 0.01 wt %
2. O
3. –
Note 1: “Exceeding 0.1 wt%” and “exceeding 0.01 wt%” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition. Note 2: “O” indicates that the
percentage content of the restricted substance does not exceed the percentage
of reference value of presence. Note 3: The ” – ” indicates that the
restricted substance corresponds to the exemption.
Türkiye
Bu cihaz Türkçe karakterlerin tamamini ihtiva eden ETSI TS 123.038 V8.0.0
(veya sonraki sürümünkodu) ve ETSI TS 123.040 V8.1.0 (veya sonraki sürümün
kodu) teknik özelliklerine uygundur.
TÜRK WEEE Uyumluluk Beyani
EEE Yönetmeliine Uygundur.
11
United Kingdom
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with the
Radio Equipment Regulations 2017 and the Restriction of the Use of Certain
Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.
Any radio operation limitations within UK are identified in Appendix A of UK
Declaration of Conformity. The full text of the UK Declaration of Conformity
is available at: zebra.com/doc. UK Importer: Zebra Technologies Europe Limited
Address: Dukes Meadow, Millboard Rd, Bourne End, Buckinghamshire, SL8 5XF
12
Warranty
For the complete Zebra hardware product warranty statement, go to:
zebra.comwarranty.
Service Information
Before you use the unit, it must be configured to operate in your facility’s
network and run your applications. If you have a problem running your unit or
using your equipment, contact your facility’s Technical or System Support. If
there is a problem with the equipment, they will contact Zebra support at
zebra.com/support. For the latest version of the guide go to:
zebra.comsupport.
Software Support
Zebra wants to ensure that customers have the latest entitled software at the
time of device purchase in order to keep the device operating at peak
performance levels. To confirm that your Zebra device has the latest entitled
software available at the time of purchase, go to zebra.com/support. Check for
the latest software from Support > Products, or search for the device and
select Support > Software Downloads. If your device does not have the latest
entitled software as of your device purchase date, e-mail Zebra at
entitlementservices@zebra.com and ensure you include the following essential
device information: · Model number · Serial number · Proof of purchase · Title
of the software download you are requesting. If it is determined by Zebra that
your device is entitled to the latest version of software, as of the date you
purchased your device, you will receive an e-mail containing a link directing
you to a Zebra Web site to download the appropriate software.
Product Support Information
· For information on using this product, see the User Guide at
zebra.com/vanityURL. · To find quick answers to known product behaviors,
access our knowledge articles at
supportcommunity.zebra.com/s/knowledge-base. · Ask your questions in our
Support community at supportcommunity.zebra.com. · Download product manuals,
drivers, software, and view how-to videos at zebra.com/support. · To request a
repair for your product, go to zebra.com/repair.
Patent Information
To view Zebra patents, go to ip.zebra.com.
13
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>