RADIO MASTER RP3 2.4ghz Nano Receiver User Manual
- August 31, 2024
- RADIO MASTER
Table of Contents
RP3 2.4ghz Nano Receiver
“`html
Specifications:
- Dimensions: 22134mm
- Weight: 4.6g (with antenna)
- Chipset: ESP8285 SX1281
- Frequency: 2400MHz-2483MHz
- Power Input: 5V
- Protocol Support: CRSF ExpressLRS v3.0
Product Usage Instructions:
Configuration:
To configure the RP3 Receiver, follow these steps:
-
Connect the RP3 to your computer using a USB VCP cable.
-
Set Configuration/MSP to 115200 in UART1 and UART2
settings. -
In Betaflight Configurator, navigate to the Ports tab and
enable the corresponding UART as Serial RX (e.g., UART2). -
Save the configuration and restart.
Traditional Binding:
To perform traditional binding with the RP3 Receiver, follow
these steps:
-
Power off your transmitter/radio.
-
Plug in and unplug your receiver three times.
-
Ensure the LED is quickly double blinking, indicating the
receiver is in bind mode. -
Power on your transmitter/radio and use the [BIND] button on
the ExpressLRS Lua script to send a binding pulse. -
If the receiver’s LED is solid, it means the binding was
successful.
FAQ:
Q: Where can I find more information about the RP3
Receiver?
A: For more details about the RP3 Receiver, please visit the
ELRS website at https://www.expresslrs.org/2.0/.
“`
RP3 Receiver User Manual
55mm ESP8285
RP3
2.4
GHZ
TOP
u.Fl u.fl
V2.0
22mm e4 SiGe 2431 L 510F C
led bind
SX1281
R T 5V –
RX TX 5V gnd
BOTTOM 13mm
4.6
GRAMS
Including 2 Antenna
– 5V T R
2X 65mm
SPECIFICATIONS
·Size: ·W eigh t: ·MCU: ·RF Chip: ·Frequency Band: ·Input Voltage: ·Receiver protocol: ·Firmware (pre-installed):
22134mm 4.6g (w/antenna) ESP8285 SX1281 2400MHz-2483MHz 5V CRSF ExpressLRS v3.0
I NCLUD ES 1x RP3 ExpressLRS 2.4ghz Nano Receiver 2x 65mm UFL 2.4Ghz T-Antenna
1x User Manual 1x CRSF wire
DEFAULT FIRMWARE RadioMaster RP3 Diversity 2400 RX
For more information, please visit the ELRS website:
https://www.expresslrs.org/2.0/
CONFIG UR AT ION
Identifier USB VCP
Configuration/MSP 115200
Serial RX
UART1 UART2
115200 115200
Open BetaflightConfigurator, go toPorts tab and enable the corresponding UART as a Serial RX (e.g. UART2 as shown above).Save and Resta. rt
Receiver
Serial (via UART)
Receiver Mode
· The UART for the receiver must be set to `Serial Rx’ (in the Ports tab) · Select the correct data format from the drop-down, below:
C R SF
Serial Receiver Provider
On the Configuration tab, click on Serial-based receiver on the Receiver panel, and select CRSF.
TRADITIONAL BINDING
Binding Phrase field must be uncommented in Device options on the RX.
1. Power OFF your transmitter/radio. 2. Plug in and unplug your receiver 3
times. 3. Make sure the LED is doing a quick double blink, which indicates
the receiver is in bind mode. 4. Power ON your transmitter/radio and use the
[BIND] button
on the ExpressLRS Lua script, which sends out a binding pulse. 5. If the
receiver has a solid light, it’s bound!
RP3 Receiver User Manual
55mm ESP8285
RP3
2.4
GHZ
TOP
u.Fl u.fl
V2.0
22mm e4 SiGe 2431 L 510F C
led bind
SX1281
R T 5V –
RX TX 5V gnd
BOTTOM 13mm
4.6
GRAMS
Including 2 Antenna
– 5V T R
2X 65mm
·: ·: ·MCU: ·: ·: ·: ·: ·:
22134mm 4.6g (w/o antenna) ESP8285 SX1276 2400MHz-2483MHz 5V CRSF ExpressLRS v3.0
1x RP3 2x 65mm U.FL 2.4Ghz 1x 1x
RadioMaster RP3 2400 RX
For more information, please visit the ELRS website:
https://www.expresslrs.org/2.0/
Identifier USB VCP UART1 UART2
Configuration/MSP 115200 115200 115200
Serial RX
Betaflight ConfigurationPorts UARTSerial RXUART2
Receiver
Serial (via UART)
Receiver Mode
· The UART for the receiver must be set to `Serial Rx’ (in the Ports tab) · Select the correct data format from the drop-down, below:
C R SF
Serial Receiver Provider
ConfigurationReceiver Serial-based receiverCRSF
1 2 3ExpressLRSLUABIND 4
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>