Z-WAGZ ZZ-2 Light Controller Connected Module Adapter Owner’s Manual

ZW-GMLC

Plug & Play, OE Light-Controller for GM vehicles!

Thank you for purchasing a genuine Z-WAGZ unit, the simplest Plug & Play module for flashing OEM lights with a press of a button. This unit comes pre- programmed with 3 different light patterns, some for halogen systems & some for LED systems.

Operation for all GM modules is the same:

1. Install the Z-WAGZ unit to the OE Light Control Module. Follow instructions on page 2 for more details and important information.

2. Turn Ignition ON or start vehicle (Ignition must be on for proper operation)

3. To activate Z-WAGZ:
   o Press and HOLD the high beam lever (5 sec) OR
   o Press and HOLD the provided push button (3 sec) OR
   o Send a 12v (+) signal to the blue wire (designed to be extended for OE up- fitter switches or any aftermarket toggle) OR
   o Press LOCK>UNLOCK>LOCK>UNLOCK on the key fob (dip switch 6 must be ON, ignition is NOT required for this method)
   Pattern 1 will begin to flash. Once pattern 1 begins, the turn signal indicators in the gauge cluster will blink 1 time then stay solid, indicating Pattern 1 has been selected. The LED on the unit will blink BLUE. See chart on page 4 for remaining pattern color  indication.

4. To change to the next pattern: (ZWAGZ must be currently active)
   o Engage either turn signal, then press and HOLD the high beam lever once more (5 sec). OR
   o Press & release the provided push button one time
   The turn signals will blink twice (then stay solid) indicating Pattern 2 has been selected. Repeat this process to switch to the next pattern.

5. To deactivate Z-WAGZ:
   o Press and HOLD the high beam lever (5 sec) OR
   o Press and HOLD the provided push button (3 sec) OR
   o Release 12v (+) signal to the blue wire (if connected this way) OR
   o Turn vehicle OFF

GENERAL NOTES:

• Vehicles equipped with LED lights should use LED patterns. Vehicles equipped with standard bulbs should use bulb patterns but may get away with LED patterns (although some consistency may be lost).
• Not all lights on the vehicle are necessarily used, some lights are not controllable via CAN data commands.
• Z-WAGZ will retain the last used pattern, even after being disconnected from the harness (if ever).
• Turn signals, headlights & reverse lights will override pattern flashing when used, until turned off again.
• Lights on the external mirrors will only flash if connected with turn signals.

Module Installation

Please fully read once through before beginning installation!

1. Make sure the vehicle is fully OFF, with driver door OPEN for 5 minutes before connecting unit.
   WARNING: this is vital to avoid tripping a checkengine light.

2. Locate the factory Light Module. In all trucks, it is mounted underneath steering wheel / driver’s side kick panel area. The module is mounted right next to the BCM unit and has (5) connectors (see picture, right).

3. With the driver door OPEN & vehicle OFF (for 5 mins minimum): disconnect the violet plug from the lighting module shown. Connect the male side of the provided T-Harness to the OE Light Module and the (removed) plug into the female side of the Z- WAGZ harness. These connectors can only fit in one place, connect in one way and are color matched to the OE plug.

4. Connect the Z-WAGZ unit to the 22-pin connector LAST. Tie-wrap the unit to another harness if desired.

5. If wanting to use the optional push button, this can be connected and run to a convenient location for access from the driver. Otherwise, the unit is fully functional from the OEM high-beam lever.

6. If wanting to connect any optional wires provided from the I/O harness, see diagram below.

7. Return to page (1) for operation instructions.

Located on the back side of the unit is a bank of (6) dip switches – you will need a pick-tool to adjust.
All dip switches are LIVE, do not unplug the module to change.

Enable Fob Activation  (see notes below)
OFF| Enable High
Beam| Enable Low
Beam| Disable Reverse Light| For LED equipped (faster)| Enable STROBE Mode| Disable Fob Activation

*With DIP switch (6) turned ON, the unit can be activated using the OEM key fob, without the Ignition requirement (all other methods). To activate, while within range of the vehicle, quickly press LOCK>UNLOCK>LOCK>UNLOCK and the flash pattern will  begin. Pressing LOCK once more will shut off the low/high beam light (so that they flash). Deactivate the unit by repeating the same process. If you enter the vehicle after the pattern has been activated using this method, the flash pattern will stay active until you  disable it (using any method) or shut the vehicle down.
WARNING: Using this method will keep the lights flashing indefinitely. Please consider the condition of your battery – although the module is not activating full ignition power (and therefore using far less current), if flashing is left ON, the battery will be  actively discharging (it will likely take 1 hour + on a newer, good battery).

Confirmed Vehicles:

*NOTE: 2023 HD trucks require a visual inspection for the presence of the Lighting Module.
2024 HD trucks are always compatible.

GM LED Status/Patterns

START-UP INDICATION

wake
Unit recognizes CAN bus (module side ONLY)| Blinks GREEN (3 times)| Upon CAN data wake
Unit recognizes CAN bus (properly)| Binks BLUE,GREEN (x3)| Upon CAN data wake
Unit detects ACC info| Blinks GREEN (1 time)| Upon Turning Ignition ON
Unit detects GEAR info| Blinks VIOLET (1 time)| Upon switching gears
Unit detects HIGH BEAM pull OR External button press(for activation)| Solid GREEN| Upon pressing High Beam lever or provided push button
Unit receives negative response for light commands| Blinks VILOET (x3)| –Contact ZZ2–
Unit not receiving confirmation for light commands| Blinks RED (x1)| –Contact ZZ2–
When unit goes to sleep| Blinks WHITE (x1)| —
CAN bus communication problem| Blinks RED + GREEN| While Z-WAGZ is activated

PATTERN INDICATION

POWER CONSUMPTION/ADDITIONAL SPECS

555 S Pompano Pkwy, Pompano Beach, FL 33069 | 929-220-1212

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>