FDF RaceShop Steering Rack Centering Tool Instruction Manual
- August 31, 2024
- FDF RaceShop
Table of Contents
FDF RaceShop Steering Rack Centering Tool
Product Information
Specifications:
- Product Name: FDF Steering Rack Centering Tool
- Intended Use: Centering steering rack
- Compatibility: Suitable for various vehicle models
- Material: 3D-printed material
Product Usage Instructions
Step 1: Preparation
Safety First: Ensure the vehicle is parked on a level surface and the engine is off. Engage the parking brake.
To access the Steering Rack:
- Remove the dust covers from the steering rack.
- Remove any residual debris around the steering rack.
Step 2: Procedure
Expose the Rack:
After sliding the dust cover off the steering rack, turn the steering wheel to one side so that the steering rack has reached its maximum travel limit.
Placing Rack Alignment Tool:
Slide the FDF rack alignment tool onto the rack until it is butted against the inner tie rod end. Ensure it sits securely without falling off.
Centering Steering Rack:
Turn the wheel in the opposite direction until it cannot be moved. Ensure the alignment tool is straight and positioned flat in the rack housing.
Step 3: Reassembly
Reinstall any components that were removed for access. Double-check all connections and fastenings for any loose or improperly secured components.
Contact Information:
- Email: support@fdfraceshop.com
- Phone: 613-955-7223 (Canada)
- Toll-Free: 888-361-7223
Conclusion
Feel free to reach out to FDF Raceshop for any questions or concerns. Stay connected with FDF Raceshop for new product releases. Follow us on Facebook, Instagram, and YouTube.
FAQ
Q: Can this tool be used on all vehicle models?
A: The FDF Steering Rack Centering Tool is compatible with various vehicle models, but it is recommended to check compatibility before use.
Introduction
- This guide will help you to center your steering rack by using a 3D-printed FDF centering tool.
Tools and equipment required for installation:
- FDF Steering Rack Centering Tool
Step 1: Preparation
- Safety First: Ensure the vehicle is parked on a level surface and the engine is off. Engage the parking brake.
- To access the Steering Rack:
Remove the dust covers from the steering rack. Remove any residual debris around the steering rack.
Step 2: Procedure
Expose the Rack:
- After sliding the dust cover off the steering rack, Turn the steering wheel to one side so that the steering rack has reached its maximum travel limit, as shown in the picture.
- Verify that the steering rack has reached its maximum travel limit and that there is no suspension interference causing any binding. Remove suspension if necessary to eliminate any suspension bind.
Placing Rack Alignment Tool:
- Now, Slide the FDF rack alignment tool onto the rack until it is butted against the inner tie rod end as shown in the figure.
- The rack alignment tool will be a fight fit and will sit on to the rack without falling off.
Centering Steering Rack:
- Now, Turn the wheel opposite way until the steering wheel cannot be moved.
- Make sure that the alignment tool is straight and positioned flat in the rack housing.
- Your Steering Rack has been centred. Please make a necessary changes if required.
Step 3: Reassembly
- Reinstall any components that were removed for access.
- Double-check all connections and fastenings for any loose or improperly secured components.
Conclusion:
Feel free to reach out to FDF Raceshop for any questions or concerns. Stay connected with FDF Raceshop for new product releases. Follow us on Facebook, Instagram and YouTube
- https://www.facebook.com/fdfraceshop/
- https://www.instagram.com/fdfraceshop/
- https://www.youtube.com/@FDFraceshop
For Racing Use only
Not For Road Use
Must be installed by a licensed Professional. Read Disclaimer included with the kit before installation.
Contact
- E-mail: support@fdfraceshop.com
- Phone: 613-955-7223 (Canada)
- Toll Free: 888-361-7223