INFIYA M1 Smart Doorbell Installation Guide
- August 30, 2024
- INFIYA
Table of Contents
INFIYA M1 Smart Doorbell
Introduction of the Camera
Product Diagram
Indicator Lights Status
| Light Status | Camera Status |
|---|---|
| Red light on | Camera is powered on |
| Red and blue light alternately flashing | Camera entering the network |
configuration state, waiting the app to connect Connecting to Wi-Fi
Blue light flashing| Wifi connection succeeds
Blue light solid| 1 . Reset camera to factory setting
Red light quickly flashing| 2 . Camera is upgrading firmware
Warm note
- When the camera in hibernation, the indicator light will turn off.
- To ensure the camera is powered on, pls hold down the RST button and check whether the light is on.
Definition of Buttons
Download APP and Register Account
Download and Install APP
- Go to the App Store or Google Play to search and download the “Wansview Cloud” APP on your smartphone. Or scan below QR code to get the APP.
Register Account
- Open the “Wansview Cloud” APP and register an account with your email and activate it.
Tips: Your password must be 8-16 characters, and contains at least the following three categories: numbers, uppercase letters, lowercase letters, or special characters.
And then you will receive an activation code in your e-mail, please enter this code in the APP, and log in.
If you don’t receive the activation code, please contact us with your account:
We will help you activate it.
Add Device
- Before Add device on the APP, please be sure that your smartphone is connected to 2.4Ghz WiFi. 5Ghz WiFi is not supported.
- And then click “Add Device” or click “+”
Select B6
- Select Cinnado, then select model B6
Camera Setup
- Place the camera near the router within 3 feet. Make sure the camera battery has enough power. Press the power button for 6 seconds until you will hear a start sound, then click “Next”.
- Hold the”RST” button for about 6 seconds until the red and blue lights flash alternately, and you will here a voice of “Di”. Please click “Flashing”.
WiFi Setup
- Your 2.4Ghz WiFi name is obtained automatically, enter your WiFi password, click“ ” button to check whether the WiFi password is correct. There shouldn’t be any spaces in your password.
- If your APP doesn’t recognize the WiFi name automatically, please activate the GPS and location authorization on the settings of your smartphone. Then go back to the previous page“ Camera Setup” and then click“ Flashing” to check if the APP recognizes the WiFi name automatically.
Wait for Connection
- The blue light flashes quickly, meaning the WiFi is connecting.
- The blue light flashes slowly, meaning the WiFi is connected.
- Until the blue light is solid, meaning the paring is successful.
You can modify the name of the camera and click “OK” to view the live video.
FAQ
If you can’t find solutions from next, please contact our customer service for help with a photo of the label (includes a QR code) on the bottom of the camera:
Fail to Connect WiFi ?
- Make sure the indicator light is flashing red and blue alternately. lf not, press the reset button for at least 5 seconds until the camera makes two DIDI sounds.
- Be sure that the WiFi is 2.4Ghz, our camera doesn’t support 5Ghz.
- Please activate the GPS and location authorization on the settings of smartphone.
- Tap ” ” button to make sure the WiFi password is correct. There shouldn’t be any spaces.
Fail to Scan ?
Adjust the distance between the camera's lens and the smartphone to 3-8 inches. Adjust the brightness to medium. Double-click the OR code to enlarge it to scan.
APP is showing Offline?
Ensure the router is working properly. Reboot the router and camera to see if the camera reconnects after that. lf not, reset the camera by holding the Reset button 5-10s and reconnect the camera. The distance between the camera and router should be within 5 meters, so camera can receive good WiFi connection.
APP Can't Recognize the TF Card?
Make sure the TF card works properly by testing the write and read files functions on a computer via a TF card reader, then insert the TF card in the camera. Please power off the device before inserting the TF card. The device only supports FAT32 format, 128GB Max; please format the TF card into FAT32 format on your computer via a card reader.
Cloud Storage
Wansview Cloud APP is FREE, Cloud Service is Optional. Even if you don't want to activate the cloud storage, you can still use the camera normally.
If the camera fails to charge, please try
Change another working power cord or adapter The solar panel won't charge the camera: change the position of the panel to ensure that it can get adequate sunlight exposure
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
CONTACT
After-sales Service
- Email US support.us@cinnado.com UK support.uk@cinnado.com
- TEL: +13236863288
- Available time: 6 pm – 3 am (PST Time) from Monday to Friday
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>