MERKURY INNOVATIONS MI-BT133 Touch Lamp With Wireless Speaker User Manual

MERKURY INNOVATIONS MI-BT133 Touch Lamp With Wireless Speaker

ON-BOARD CONTROLS (TOP)

SPECIFICATIONS

• Dimensions: 4.1″ x 4.1″ x 14″ (Height X Width X Depth)
• Weight: 1.12Ib
• Input Voltage: SV 1A
• Dutput Voltage: 3.N
• Output Watts: 3W
• Indoor use only

Bluetooth(I Information
BT Version: V5.4
Bluetooth0 Range: 1 Om

Depends on individual use and may be slightly more or less than the time specified

Technical specifications

• Sound: Mono
• Bluetooth IC Model and Version: AB5365A / V5.4
• Bluetooth Pairing Name: MERKURY BT133
• Bluetooth Speaker Output: SW
• Frequency Response: 20Hz-20kHz
• Distortion: :s:10% (Tested with iPhone at max volume)
• SNR: :c,BSdB (Tested with iPhone at max volume)
• Charging Current: Max 1 000mA
• Battery capacity: 2000mAh
• Bluetooth Range: 10 meters
• BOB Certification for BT IC: Yes
• Battery with PCM: Yes
• Play Time: 3.5-4 hours
• Charging Time: 3-4 hours
• Charging Port Type: Type C
• Number of Channels: 1
• Speaker Size: 40mm H=21 rTVTI

INSTRUCTIONS

• Charging the Battery
  • Use the provided USB cable to fully charge the desk lamp.
  • Place the lamp on a stable surface.
  • Touch the power button on top to turn on the lamp.
• Using the Lamp
  • Touch the power button to cycle through the three light modes: warm white, cold white, and neutral light.
  • Press and hold the power button to adjust the brightness infinitely in the current light mode.
  • Touch the power button again to turn off the lamp.
• Connecting to a Bluetooth Device:
  • Press the power button to turn on the lamp.
  • On your Bluetooth device, search for “MERKURY BT133” in the Hsi of available devices.
  • Select “MERKURY BT133” to connect. An alert will sound indicates the speaker is connected.
  • You can now play music through the speaker.

TROUBLESHOOTING

• No power
  Recharge yourTouchSound speaker using the included
  USB type C charging cable.
  If not working try using a different cable.

• Music is not playing over Bluetooth
  Make sure your Bluetooth device has an A2DP profile.
  Check if both devices are paired and connected over Bluetooth”. Restart the speaker to reconnect your Bluetooth” device.

• Bluetooth device will not reconnect with the speaker
  Navigate to your Bluetooth settings menu on your Bluetooth” device, tap “MER KURY BT133” and select “Forget”. Now follow the steps to pair your device again.

TECHNICAL SUPPORT

If you are experiencing problems, do not attempt lo fix the product by yourself or return it to the store you bought it from.  Please refer to the user manual or just contact our helpful support team:

Merkury Innovations
45 Broadway, 3rd Floor, If you are experiencing problems, do not attempt lo fix the product by yourself or  return it to the store you bought it from.
Please refer to the user manual or just contact our helpful support team: New York, New York 10 006
www.merkuryirv1ovalions.com
support@merkuryirvovations.com

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the two following conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

©2024 Merkury Innovations, LLC.
To explore our full selection of products, visit us at: www.merkuryinnovations.com
The illustrated product and specifications may differ slightly from that supplied. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. All other trademarks and trade names are those of their respective owners.
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>