ASUS BT10 Tri Band WiFi Router User Guide
- August 26, 2024
- Asus
Table of Contents
ASUS BT10 Tri-Band WiFi Router
Model: BT10
- If no 6GHz SSID is displayed, please check whether your OS and client device are fully licensed to support the newly released 6GHz band. You can check with your OS and client device provider for the Wi-Fi 6E driver release schedule.
Hardware Explanations
- Plug the adapter into the DCIN port, and press the power switch.
- The LED indicator will light up when your hardware is ready.
ZenWiFi BT10 Overview
WAN/LAN1 port, 10G WAN/LAN2 port
Connect your optical modem to either a WAN/LAN1 port or a 10G WAN/LAN2 port
with a network cable.
10G LAN3 port
Connect your PC to a LAN port with a network cable.
Specifications
| DC Power adapter | DC Output: +12V with max 3A current |
|---|---|
| Operating Temperature | 0~40oC |
| Operating Humidity | 50~90% |
- The USB port is available for (UE) LTE USB dongles.
Before Setup
Preparing to set up an AiMesh WiFi system
- Find three ZenWiFi BT10, and power them on.
- Use a network cable to connect your optical modem to either the WAN/LAN1 port or the 10G WAN/LAN2 port of ZenWiFi BT10 with the “Main Unit” sticker. This ZenWiFi BT10 will be the AiMesh router, and the other two ZenWiFi BT10 will be the AiMesh node.
- The LED turns solid blue to indicate that ZenWiFi BT10 is ready for setup.
ASUS Router App
Download the free ASUS Router App to set up and manage your router(s). 
AiMesh Setup Steps
Prepare
Place your AiMesh router and nodes in the same room and at least 1 meter apart
during the setup process.
AiMesh node
Keep your AiMesh nodes powered on and standby for AiMesh system settings.
Launching ASUS Router App
Launch the ASUS Router App, and then follow the on-screen instructions to
finish the AiMesh setup.
NOTE: When you’re using a wireless backhaul to connect your router and AiMesh node, the WAN/LAN ports on your AiMesh node can be used as LAN ports.
Troubleshooting
If your AiMesh router cannot find any AiMesh node nearby or synchronization fails, please check the following and try again.
- Move your AiMesh node closer to the AiMesh router ideally. Ensure that it is within 3 meters.
- Your AiMesh node is powered on.
Relocation
Locate the AiMesh router and nodes at the best place.
NOTES: To minimize interference, keep the routers away from devices like cordless phones, Bluetooth devices, and microwave ovens. We recommend that you place the routers in an open or spacious location.
ZenWiFi BT10 LED indications 
FAQ
Does the AiMesh router support Access Point mode?
A: Yes. You can choose to set the AiMesh router as router mode or access point
mode. Please go to web GUI (http://asusrouter.com), and go to the page
Administration > Operation Mode.
Could I set up a wired connection between AiMesh routers (Ethernet
backhaul)?
A: Yes. AiMesh system supports both wireless and wired connections between
AiMesh router and node to maximize throughput and stability. AiMesh analyzes
the wireless signal strength for each frequency band available and then
determines automatically whether a wireless or wired connection is best to
serve as the inter-router connection backbone.
- Follow the setup steps to establish a connection between the AiMesh router and node via WiFi first.
- Place the node in the ideal locations for best coverage. Run an Ethernet cable from the LAN port of the AiMesh router to the WAN port of the AiMesh node.
Where can I find more information about the Mesh WiFi system?
A: Technical support site: https://www.asus.com/support 
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions
for you to be able to responsibly recycle our products, batteries, other
components, as well as packaging materials. Please go to
http://csr.asus.com/english/Takeback.htm for detailed recycling information
in different regions.
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and
Restriction of Chemicals) regulatory framework, we published the chemical
substances in our products on the ASUS REACH website at
http://csr.asus.com/english/REACH.htm
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
FCC STATEMENT
FCC regulations restrict the operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet in the 5.925-6.425 GHz band. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems. This equipment has been tested and found to comply with the limits for a class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Prohibition of Co-location
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
IMPORTANT NOTE
Radiation Exposure Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. End users must
follow the specific operating instructions to satisfy RF exposure compliance.
To maintain compliance with FCC exposure compliance requirements, please
follow operation instructions as documented in this manual.
WARNING! This equipment must be installed and operated by provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 50 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Safety Notices
- Use this product in environments with ambient temperatures between 0°C(32°F) and 40°C(104°F).
- Refer to the rating label on the bottom of your product and ensure your power adapter complies with this rating.
- DO NOT place on uneven or unstable work surfaces. Seek servicing if the casing has been damaged.
- DO NOT place or drop objects on top and do not shove any foreign objects into the product.
- DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem during electrical storms.
- DO NOT cover the vents on the product to prevent the system from getting overheated.
- DO NOT use damaged power cords, accessories, or other peripherals.
- If the Adapter is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
- To prevent electrical shock hazards, disconnect the power cable from the electrical outlet before relocating the system.
- DO NOT mount this equipment higher than 2 meters.
Compliance Statement of Innovation, Science and Economic Development Canada
(ISED)
This device complies with Innovation, Science and Economic Development Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device. Operation in the band 5150–5250 MHz is only for
indoor use to reduce the potential for harmful interference to co-channel
mobile satellite systems. CAN ICES-003(B)/NMB-003(B)
Radio Frequency (RF) Exposure Information
The radiated output power of the ASUS Wireless Device is below the Innovation,
Science, and Economic Development Canada radio frequency exposure limits. The
ASUS Wireless Device should be used in such a manner that the potential for
human contact during normal operation is minimized. This equipment should be
installed and operated with a minimum distance of 66 cm between the radiator
and any part of your body. This device has been certified for use in Canada.
The status of the listing in the Innovation, Science and Economic Development
Canada’s REL (Radio Equipment List) can be found at the following web
address:http://www.ic.gc.ca/eic/site/ceb-bhst.nsf/eng/h_tt00020.html
Additional
Canadian The information The on The RF The exposure The also The can The be
The found The at The the The following The web The: The
https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html
For product available in the US/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux États-Unis et au Canada, seuls les canaux 1 à 11 peuvent être utilisés. La sélection d’autres canaux n’est pas possible. This device is restricted for indoor use only.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>