PGST PG-500 Alarm Host User Manual
- August 26, 2024
- PGST
Table of Contents
PGST PG-500 Alarm Host
Function Introduction
- support APP Push,SMS push voice moni toring and other mult i-channel alarm mode.
- 8 wired defense zones,200 wireless defense zones【support for renaming】
- Up to learn 8 wireless remotes.
- LCD display with built-in clock,intuitive and convenient
- The whole process of real voice prompts,installation settings and daily operations are more user-friendly.
- Automatically send message when low battery.
- Ac power failure and AC recovery SMS prompt
- Built-in intercom speaker, can realize duplex intercom function.
- Built-in 433 transceiver module, which can be linked to wireless siren and smart home system (optional)
- Set and control the alarm by APP
- Timing arm and disarm function
- Built-in multi-languages,free to switch.
- Remote control in different places: the host arm, disarm, monitor, intercom and so on
- Additional functions：The alarm can be used as telephone，and it can make phone calls,inquire phone charges and prepaid recharge by alarm keyboard.
- One-key control: arming out, arming at home, arming by remote control, arming by remote phone
- Instant, at home, 24 hours, bypass multiple zone programming functions
- Code matching: adding new accessories is convenient, fast, safe and efficient
- Remote control in different places: mainframe arming, disarming, monitoring, intercom and so on
- Event record query: host and APP can query historical event records.
- A variety of arming modes: remote control instant arming, outgoing host delayed arming, home host stay arming, designated time timing arming, remote phone remote arming
- Built-in lithium battery rechargeable battery pack, power failure alarm function.
Features
- Simple style, good feel.
- Based on the multitasking design of Freertos system, it has an excellent user operation experience
- WiFi automatic time calibration, to ensure accurate clock and support time zone setting, which is convenient for use in multiple countries
- LCD graphic display, built-in perpetual calendar clock, operation steps, smartphone control, support for multi-language menus in many countries and regions, voice operation prompts
- Embedded powerful 32-bit Cortex-M3 CPU control
- WiFi network alarm, support APP push to ensure stable and reliable alarm performance
- Up to 8 remote controllers and 200 wireless detector learning s storage locations
- Supports multiple alarm type settings for main door, hall, SOS, bedroom, window, balcony, perimeter, smoke, gas, carbon monoxide, water leakage, etc.
- Supports multiple extended alarm situations such as main power failure and backup battery power shortage
- With wireless sensor battery voltage low alarm function
- Support multiple alarm modes such as going out arming, stay in arming, 24-hour defense zone, doorbell, etc.
- fixes the keyboard on the wall through the four positioning holes on the back cover of the keyboard, as shown in the below,
- fixes the keyboard on the wall or the 86 box installed in the wall through the four positioning holes on the back cover of the keyboard, as shown in the figure below
Alarm Host Installation
The host should be installed in the center of the protected area, in order to take into account the best reception effect for all wireless detectors. Pay attention to the installation of the host as far as possible away from large metal objects or household appliances with high frequency interference, and avoid shielding objects such as reinforced concrete walls and fire doors.
Front view of the panel
Back view of the panel
SIM Wire connecting terminal
LCD display
Cellphone APP
APP download
The Smart Life APP has been released to major global app stores. You can search for “Smart Life” in the app store or scan the QR code on the cover to download.For users in mainland China, please scan the QR code of the official website to download; for users from non-mainland China, please scan the QR code of the Google Play link to download.The smart life APP downloaded from the official website link and Google Play link is the same APP, but the download channel is different.
Note: Mainland China may not be able to download the APP through the Google Play link QR code due to network reasons. Select the corresponding device and swipe left to delete the device.Click the appropriate device to rename the device. The description of the APP in this manual is based on the Andriod system. Some descriptions may be different due to different versions of the APP or different iOS systems. All the APP versions actually installed on the mobile phone shall prevail.
Installation
Use your cellphone to scan the QR code on the back cover directly to download
and install it.When the host is in the normal power-on and disarm state: input
the command engineering password 6666# — 00 — #, and the voice broadcast will
announce that it has entered the WIFI distribution network mode. Make sure the
host computer and mobile phone are in the same WIFI network.
Run the mobile APP software, log in with the registered account on the user
login interface (New users need to register an account). On the APP device
list interface, press the “Smart Configuration” button in the upper right
corner to enter the smart configuration interface.Select the WIFI network in
the APP and enter the WIFI password, press the “OK” button to start the
configuration.
- Method 1: Click to add settings in the APP “Smart Life”, and operate according to the APP’s prompts (turn on Bluetooth). If the network configuration is successful, the detector will broadcast a voice, indicating that the host has been successfully connected to the Internet. If: WIFI configuration more than 120 seconds without successful configuration, it means WIFI configuration failed.
- Method 2: Click to add a device in the APP “Smart Life” – (turn on Bluetooth) – click the socket (Bluetooth + WIFT) – confirm the indicator light flashes quickly – click the fast flash – next step – Continue – If the network configuration is successful, the detector will broadcast a voice, indicating that the host has been successfully connected to the network. If the WIFI configuration exceeds 120 seconds and the configuration is not successful, it means that the network access configuration fails.
As shown below:
1. Click to add device:
2. Connection
3. Unbinding the mobile APP from the hostOperating the host: Main menu – Accessory settings – Unbinding – Confirm. Host prompts “Unbinding”Add remote control through mobile APP
* Go to the “Accessories” menu.
* Press “Remote Control Settings” to enter the remote control setting interface, and the APP will call the number of remote controls that the host has learned.
* Press the “Add Device” button to enter the remote control learning interface
* After pressing the “Start Learning” button, send the remote control learning instruction to the host, press any key of the remote control to be learned to complete the learning, and the host sends the learning success information to the APP.
* The APP pops up “Successful study” to complete the study.
* The APP returns to the remote control setting interface, and recalls the number of remote controls that the host has learned: As shown below, 
4. Add wireless detectors through mobile APP
* Enter the “Settings” menu.
* Press the “Add Device” button to enter the detector learning interface.
* Press “Detector” to select the name of the detector to be learned.
* Press the “Zone Type” column to select the required defense zone type for the corresponding detector.
* After pressing the “Start Learning” button, send the detector learning instruction to the host.
* Trigger the launch of the learning detector, complete the learning, and the host sends the learning success message to the APP
* The APP pops up “Successful learning” and the APP returns to the detector settings interface, recall the number of all detectors that the host has learned.
5. Delete the remote control through the mobile APP
* Long press “Remote Control” on the remote control settings interface
* A dialog box pops up, if the user confirms the deletion, press “Yes” and the APP sends the command to delete the remote control to the host.
* The APP returns to the remote control setting interface,and recalls the number of remote controls that the host has learned. If the deletion is successful, the number of remote controls will return to zero. As shown below：
6. Delete wireless detector through mobile APP
* In the detector setting interface, click the “Delete” icon of the detector row to be deleted in the learned detector list.
* A dialog box pops up, if the user confirms the deletion technique “Yes”, the APP sends an instruction to delete the corresponding name detector to the host.
* The APP returns to the detector setting interface, and recalls all the detectors that the host has learned. The deleted detectors are gone. As shown below：`
7. Code matching through mobile phone APP and external wireless alarm signal.
* This functiqon only controls the host to transmit the code matching signal to the external wireless alarm in the learning state through the APP.
* See Example 2 [and external wireless alarm code matching].
* During wireless alarm code matching, long press the code matching button and the alarm will ring three times, then release the button to trigger the host to send a signal. When the alarm signal is received by the host, it will give two beeps, indicating that the connection is successfulFunction Settings
System Settings
In the standby state, enter the four-digit project password [6666] project password, press [#] key to confirm. The host voice prompts: “Please enter the command”, and at the same time the [SET] light is on and the display shows [-], indicating that it has entered the setting state. When setting the state, you can repeatedly perform a variety of function setting operations. If you stop operating the keys on the host for more than 30 seconds, the host will automatically exit the settings and return to the standby state. Note: The factory default value of the project password is [6666].The following settings are all performed in the setting state, input the setting address and setting content in turn, and press the “#” key to complete the setting.
Host function button
Host screen display status type
set content directory| Setting address| setting content|
---|---|---|---
WiFi network configuration
|
00
| | Input 00-# host voice broadcast has entered WiFi network configuration mode; 1. The network distribution time is 60s, and the voice prompts for successful networking
2. When the configuration time is up, the WiFi configuration fails
Language configuration|
11
|
1-11#
| 1 Chinese, 2 English, 3 Italian,4 Polish,
5 Russian, 6 Greek, 7 French,8 German
9 Spanish,10 Portuguese, 11 Hungarian
Remote control code| 21| 1-8#| example 1, up to 8 can be set
Remote control delete| 22| |
Wireless defense zone code| 23| 1-199#| example 2, up to 200 can be set
Delete a wireless zone| 24| 1-199#|
Delete all wireless defense zones| 25| |
Zone alarm mode setting| 26| 1-208#| example 3, up to 208 (including 8 wired
zones) can be set
Siren time setting| 32| 00-15#| 00-15 is the ringing time, the unit is
minutes, the factory value is [03]
Arming delay time setting|
33
|
00-99#
| 00 ~ 99 is the arming delay time, the unit is second, the factory value is [00]
Alarm delay time setting
|
34
|
00-99#
|
00~99 is the alarm delay time, the unit is second, the factory value is [00]
Phone dialing times settings
|
35
|
0~9#
| 0~9 is the number of dialing times, the factory default value is [3]
---|---|---|---
Modify user password|
38
| | 0000-9999 Factory
default: 1234
Revise engineering password
|
39
|
0000-
9999#
| Enter the four-digit engineering password and press “#” Note: The factory
default is: 6666
Host Keypad Lock Settings|
40
|
0-1#
| “0” means: close, “1” means: open, the factory value is [0]
Host timing function settings|
41
|
0-1#
| “0” means: close, “1” means: open, the factory value is [0]
Host timing arm and disarm settings
|
42
|
AABB, XXYY
| AABB stands for: disarm time
— hours and minutes, XXYY stands for: arm time hours and minutes
Host reset settings|
43
| | Do not delete remote control accessories
Host history query|
44
| | Press “2” to scroll up, press “8” to scroll down
Clear host history| 45| |
Arm/disarm SMS prompt settings (optional)|
46
|
0-1#
|
“0” means: close, “1” means: open, the factory default is [0]
clock setting
|
48
| Year/month
/ day/hours
/minutes
|
Example4
---|---|---|---
Delete the alarm| 51-56| |
Zone alarm type setting|
60
|
1-208#
| See example 6 (including 8 wired defense areas)
Host IMEI query|
63
|
0-32#
| See Example 7
(99 means no signal)
Example 1. Remote control code
In the disarmed state, enter the engineering command [6666#] -[21] key + [N] (N represents the serial number of the remote control), press the [#] key to confirm, the host will beep once, and the voice prompts “The remote control sends a code” ”[ ] The pairing icon will be on for a long time, and the LCD will display the remote controller that is pairing at this time. Press any key on the remote controller that needs to be paired; after the host receives the signal, a “beep” will sound, and the voice prompts “Successful learning” ”[ ] The pairing icon is off, and the remote controller is successfully paired.After the code is successfully matched, it will automatically return to the previous layer. If you need to operate, repeat the operation method of the previous action: [6666#] → [21] → [1-8#]
Note: The same remote controller can only be paired once, and can be paired with up to 8 remote controllers.Support the learning of 8 remote controls, click “+” to learn accessories, Follow the instructions of the host to operate. If the host voice prompts “Accessories have been learned”, it means that the code of this remote control has been learned or duplicated with other learned detector codes, please try another remote control and try again.
Example 2. Wireless zone matching
In the disarmed state, enter the engineering command [6666#]-[23], then enter the defense zone to be paired [1-200], and press the [#] key to confirm. The LCD displays the corresponding defense area, and the voice prompts “detector sends a code” to trigger the detector that needs to be paired, and the host receives the message. After the number is entered, a “beep” will sound, the voice prompts “Successful learning” and two [ ] pairs are matched, and the icon goes out.
- Operation method: 【6666#】→ 【23】→ 【XX】→【#】
- XX stands for: 1-200 zone number.
Example 3. Zone alarm mode and alarm type setting
In the disarmed state, enter the engineering command[6666#]-[26] key, then enter the wireless zone number [1-200], and then enter the alarm type of the accessory [1~8], and press “#” to confirm;The host will beep once, and the voice prompts “set successfully”. The accessory alarm mode has been edited successfully.
- Operation method: [6666#]→ [26]→ [XX] →[Y]→ [#]
- XX represents: two-digit zone number; Y represents: alarm mode For example: 02 zone alarm mode is set to go out to arm Operation method: [6666#]→[26]→[02]→[1]→[#]
Zone alarm mode
When the alarm mode of the accessory is set to “0”: in any state, the accessory will not trigger the host to alarm;
When the alarm mode of the accessory is set to “1”: only when the host is out
of the armed state, or stay at home to arm, the accessory will trigger the
host to alarm;When the accessory’s alarm mode is set to “2”: only when the
host is arming outside, the accessory triggers the alarm host to give an
alarm, and when the host is at home, the accessory triggers the alarm host and
does not alarm;
When the alarm mode of the accessory is set to “3”: no matter what state the
host is in, the trigger of the accessory will cause the alarm host to alarm
(it will also alarm when it is not armed).
Example 4. Clock setting method
In the disarmed state, input the engineering command [6666#]- [48 ], then
input the last two digits of the current year [AA]; add the two-digit month
[BB]; add the two-digit date [CC] ]; add the current hour time (24-hour clock)
[DD ]; add the current Minute time [EE]; press [#] key to confirm, the host
voice prompts,
the operation is successful How to do it:【6666#】→[48]→ 【AA】→【BB】→【CC】→【DD】→[
EE ]→ [ # ]
- AA stands for: the last two digits of the current year.
- BB stands for: the two-digit number of the current month
- CC stands for: Two digits of the current date.
- DD stands for: Hours of the current time: (24-hour clock).
- EE stands for: Minutes of the current time.
For Example: May 26, 2017 at 17:30 pm
Operation method: [6666#]→[48]→[17]→[05]→[26]→[17]→[30]→[#]
Example 5. Alarm phone number setting
In the disarmed state, enter the engineering command [6666#]-[51-56] key, then enter the mobile phone number, press the [#] key to confirm, the host voice prompts “operation successful”. Operation method: [6666#]→ [XX]→ [YY…YY]→ [#]
- XX stands for: 1~6 groups of telephone codes [51~56].
- YY–YY represents: set the telephone (mobile phone) number.
For example: take 13811110751 as the first group of alarm calls.
Operation method: [6666#]→[51]→[13811110751]→[#]
Example 6. Alarm type setting
In the disarmed state, input the engineering command [6666#]-[60] key, select
the corresponding zone number[02-99] key, then input [1-8] zone alarm type,
press [#] to confirm, and the voice prompts” Set up successfully”
Operation method: [6666#]→ [60]→ [XX]→ [A]→ [#]
XX represents the zone number: [1-208] correspond to zones 01 to 208 respectively.A stands for alarm type: [1] SOS alarm,[2] Fire alarm,[3] Gas leak, [4] Door lock alarm, [5] Hall alarm,[6] Window alarm, [7] Balcony alarm, [8] Perimeter alarm.The alarm type is sent to the mobile phone by SMS
- For Example: Set zone 10 as a fire alarm
- Operation method: [6666#]→ [60]→ [10]→ [2]→ [#]
Exit Settings
- After the setting is completed, you need to exit the setting state, enter the [*][#] key, the host will make a beep, and exit the setting state. The [SET] light goes out and returns to the standby state.
Exit Settings
Under normal circumstances, the alarm panel usually only has the following four states:
- Arming status: After arming, 1-208 zone alarm is valid.
- Arming at Home: After arming, set it to [Arm at Home] to alarm in a valid zone.
- Disarm status: After disarming, the 1-208 zone will not alarm (except for the 24-hour zone)
- Setting status: When setting, all defense zones will not alarm.
Daily operation
The remote control is a device that performs various functions on the alarm host by radio. The function is to facilitate the user to carry out operations such as going out arming, arming at home, emergency alarm, and disarming the alarm host outside the door or entering the house.
- Arming when going out: Press the [ ] key, the main unit is in the arming state immediately. Arrange security tasks(referring to anti-theft) to make the host enter the alert state, also known as fortification and vigilance.
- Disarm operation: press the [ ] key, the main unit will alarm immediately or be in disarm state. Revocation of security tasks (referring to anti-theft), also known as disarming.
- Arming at home: Press the [ ] key to be in the arming state at home (stay behind). When the user is at home, he only needs to set an alert state for the entrance, exit or perimeter, which is also called home defense.
- Emergency alarm: Press the [ ] key, the host will send an alarm immediately. After the host generates an alarm task, the on-site sound and light alarm is issued, and a series of alarm actions such as the alarm content are pushed to the mobile APP.
- Defense zone triggering: When the detector in the armed state or set to 24-hour defense zone detects someone or the door is opened, the detector triggers, and an alarm task is generated.
- Arming delay: After the host is armed, the extended time is set to avoid the alarm when the user leaves the scene and passes through the arming area. It is also called the exit delay.
- Alarm delay: After the user comes back and triggers the detector after passing through the armed area, the host will not alarm immediately, providing a period of time for the user to disarm the host, and the host will alarm if the host cannot be disarmed after timeout, also called entry delay.
Remote Control
- Dial the phone number connected to the alarm host through the phone (mobile phone).
- After the set number of rings is passed and the phone is connected, the user operates the key according to the voice prompt.
Sos
In the family, some special situations sometimes occur: the elderly or children have a sudden illness and need first aid; a fire suddenly occurs in the home and needs to be rescued; gangsters enter the house to commit robbery and need to report to 110. At this point, just press the [ ] emergency button on the main unit, the [ ] button on the remote control, and the emergency button. The alarm system will alarm immediately, and automatically make a phone call to alarm.
- Remote control operation: Press the [ ] button on the remote control once.
- Host operation: [ ] emergency button on the host keyboard.
Maintenance
System detection
Although the alarm system is used every day, it must be regularly maintained and tested to ensure the stable, reliable and safe operation of the alarm system. Usually, the alarm host must be inspected comprehensively every three months, and the detector should be inspected once a month, and at least every three months if there is no condition.
Host detection
- Whether the host can arm and disarm normally.
- Whether the host alarm can make outgoing calls normally.
- Whether the signal of the detector can be received normally or whether the backup battery is normal.
Probe detection
- Manually trigger the detector to check whether the alarm is normal.
- Check the batteries of all detectors to see if they are undervoltage. Test the launch of the wireless detector to see if it can communicate with the host.
Technical parameters
- Input voltage： DC5V
- Working current： screen off <100mA, screen on <200mA
- stand-by current： <55mA
- Alarm current： <600mA
- Radio frequency： 433MHz
- RF code： 1527(330K)
- Backup battery： 3.7V/1000mAh rechargeable lithium
- Siren Alarm： >100dB@1m
- Wireless distance： <100m
- Operation temperature： -10℃—55℃
- Relative humidity: <80%RH (non-condensing)
Notes
- Do not disassemble, repair and modify the product without permission, otherwise accidents and failures may occur.
- Do not drop the product on the ground or hard objects to avoid strong impact, resulting in malfunction and damage.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and to radio coordaica vons. evenst, chioes is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’ s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
FAQ
- Q: How do I reset the alarm host?
- A: To reset the alarm host, refer to the system settings in the user manual or contact customer support for assistance.
- Q: Can I expand the system with additional detectors?
- A: Yes, you can expand the system by adding compatible wireless detectors. Follow the installation instructions in the user manual for integration.
Scan
Documents / Resources
| PGST
PG-500 Alarm
Host
[pdf] User Manual
2AIT9-PG-500, 2AIT9PG500, PGST-PG-500, PG-500 Alarm Host, PG-500, Alarm Host,
Host
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>