ZEVNI A04651 19 Inch Island Light Instruction Manual
- June 9, 2024
- ZEVNI
Table of Contents
A04651 19 Inch Island Light
Instruction Manual
A04651 19 Inch Island Light
Item Number: A04651
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides.
Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required. -
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is 18W.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials
such as scouring pads or powders, steel wool or abrasive paper.
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools
as below picture
PARTS TYPE & QTY INCLUDING:
(C) Mounting plate (1)
(D) Screw (4)
(E) Canopy (1)
(F) Strain relief (3)
(G) Cord (3)
(H) Socket (3)
ACCESSORIES & QTY ENCLOSED:
(A) Mounting screw (2)
(B) Wire connector (3)
(I) Allen wrench (1)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
Make installation Connect wires according to the below chart Step A1 » Unscrew screws (D) from mounting plate (C) and canopy (E).
Step A2 » Attach mounting plate (C) to the outlet box with mounting screws (A).
Step A3 » Make wire connections
Connect wires as below wires connecting shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart Connect wires according to the below chartConnect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord ( round & smooth )| Parallel cord ( square & ridged )
Clear,Brown,Gold or Black without tracer| Clear,Brown,Gold or Black with tracer
Insulated wire ( other than green) with copper conductor| Insulated wire ( other than green ) with silver conductor
*Note: When parallel wires ( SPT I & SPT II ) are used. The neutral wire
is square shaped or ridged and the other wire will be round in shape or smooth
( see illus. ) Twist wires together with plastic wire connectors until tightly
joined, and wrap each connector with approved electrical tape. Be sure that no
wire strands are exposed and then carefully tuck all wires into the outlet
box.
Step A4 » Raise canopy (E) to the ceiling and secure canopy (E) in place by
threading screws (D) into canopy (E) and mounting plate (C).
Step A5 » The length of cords (G) is adjustable:
- Use Allen wrench (I) to unscrew the screws in strain reliefs (F), carefully pull and push cords (G) through canopy (E) and strain reliefs (F) to lengthen or shorten the length of cords (G).
- Once the desired height of fixture is achieved, carefully tighten the screw till snug.
- Check everything is already installed properly, then you could turn on the light. Enjoy!
+1 850 296 2377 Working hours : Mon Fri 9:00 16:00 EST
homecustomercare@outlook.com
www.ihomeangel.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>