Mira S43J Leap Quadrant Shower Enclosure Installation Guide

Installation Guide LeapQuadrant Enclosure (S43J)
These instructions must
be left with the user

INTRODUCTION

Thank you for purchasing a quality Mira product. To enjoy the full potential of your new product, please take time to read this guide thoroughly, having done so, keep it handy for future reference.
The following pages aim to provide comprehensive installation instructions, plus advice on how to care and maintain your product.
We recommend that the unit is installed by a qualified plumber or engineer.

GENERAL INFORMATION

General

1. Read all of these instructions and retain this guide for later use.
2. Pass on this guide in the event of change of ownership of the installation site.
3. Follow all warnings, cautions and instructions contained in this guide.
4. Remove all protective tape from the enclosure before installation.
5. Excessive flow rates may lead to overflowing and leaking.
6. Water Spray may extend beyond the entrance of walk-in enclosures and we recommend tiling of the adjacent area.
7. We recommend a drainage test is carried out to ensure the waste is adequate for the flow delivered.
8. Doors that open outwards may drip water onto floor, ensure the floor covering will not be affected by water.
9. Walk ins and divider panels are designed to minimise water escaping outside the enclosure but by their very nature are not fully water tight.

Safety Information

1. Care should be taken when drilling into walls and floors to avoid any hidden pipes or wires.
2. We strongly recommend that all glass panels are moved by a minimum of two people and that any protective packaging along the glass edges is kept in place for as long as possible to prevent damage before installation.
3. During installation we recommend additional help in lifting heavy doors and side panels.
4. Wear protective footwear when lifting panels.
5. Wear safety glasses when drilling.

Before Fitting theEnclosure

1. Ensure the tray is level and walls are vertical and square.
2. Shower fittings should be positioned such that water discharges down the centre line of a bath or across the opening of a shower cubicle door.
3. Ensure water is not directed at the shower door or side panels. This could result in water spraying outside of the enclosure.
4. Ensure the door opening is positioned correctly and is adequate for all users.
5. Ensure there is a complete silicone seal between the tray and finished wall.
6. Ensure the door is undamaged and no parts are missing.
7. Ensure the size of door/panel is suitable for the installation. Tempered safety glass cannot be cut.
8. Ensure nothing can impact the door or glass panels during operation.

When Fitting theEnclosure

1. The wall channels must be installed onto a tiled or waterproof finished flat and even wall surface. Failure to do so will result in an unsatisfactory seal, which may cause property damage.
2. We recommend our enclosures are fitted onto shower trays.
   Warning! The use of grout/tile cleaners, scale removers, abrasive scourers, drain unblockers and other powerful detergents may lead to damage of metallic, plated and plastic surfaces, including the tray and shower waste.

Use of theEnclosure

1. High water pressure and flow may lead to excessive splashing causing water to escape outside of the enclosure.
2. In certain circumstances such as cleaning, water sprayed directly at the seals may escape outside of the enclosure.

GUARANTEE

For domestic installations, your enclosure has the benefit of our lifetime guarantee which starts from date of purchase.
For non-domestic installations, we guarantee the product against any defect in materials or workmanship for a period of one year from the date of purchase.
For terms and conditions refer to the back cover of this guide.

RECOMMENDED USAGE

TOOLS REQUIRED

PACK CONTENTS

INSTALLATION

Height of Enclosure (mm)|

1900

---|---
Min/Max Frame Adjustment| Enclosure Size| Minimum (mm)| Maximum (mm)
| 800| 768| 798
| 900| 868| 898
| 1000| 968| 998
| 1200| 1168| 1198

(a) Install the shower tray in accordance with the manufacturer’s instructions.
Caution! Make sure that the shower tray is level and that the walls are vertical and square. Note! Cover the tray waste to prevent the loss of small parts.
Note! Protect the tray surface during enclosure installation.(a) Remove the wall channel.(a) Position the wall channel on the wall. Using a spirit level make sure that it is upright.
(b) Mark the position of the fixing holes, then remove the wall channel.
(c) Drill with a 6 mm masonry bit (not supplied) and plug using the wall plugs (supplied).(a) Position the second wall channel on the wall. Using a spirit level make sure that it is upright.
(b) Mark the position of the fixing holes, then remove the wall channel.
(c) Drill with a 6 mm masonry bit (not supplied) and plug using the wall plugs (supplied).
(d) Apply silicone sealant along the length of the wall and at the bottom where the wall channel will be placed, including the top of the tray.
(e) Position the wall channel on the wall and install the fixing screws.
(f) Fully tighten the fixing screws, making sure that the wall channel is upright. (a) Cut the seal to length and fit onto the glass.
(b) Fit the glass into the bottom track making sure that the seal locates correctly.(a) Install the screws to both sides to secure the assembly.(a) Cut the seal to length and fit to the top of the glass.
(b) Fit the top track over the glass and seal making sure the seal locates correctly.(a) Install the screws to both sides to secure the assembly.(a) Apply silicone sealant along the length of the wall and at the bottom where the wall channel will be placed.(a) Install the first wall channel into the door frame and hold in position.
(b) Install the door frame over the wall channel that had been secured to the wall earlier. Make sure that you do not smudge the silicone sealant applied in the previous step.
(c) Adjust the door frame so that it is in the correct position.
(d) Install the wall channel fixing screws through the access holes in the door frame.
Note! The plastic sleeve is provided as an installation aid.
(e) Fully tighten the fixing screws, making sure that the wall channel is upright.(a) Using the 3.0 mm hexagonal wrench (supplied), turn through 90° clockwise to lock the door frame in position.(a) Using the 3.0 mm hexagonal wrench (supplied), turn through 90° clockwise to lock the door frame in position.(a) Install the seals to the glass.(a) Install the flexible track infill strip to the top and bottom tracks.(a) Lubricate the rubber strip with washing up liquid or a suitable lubricant to help aid installation.
(b) Install the rubber strip as shown above to both sides, working from top to bottom.
(c) Install the infill strip.(a) Turn the door so that it in the correct orientation.
(b) Fully turn the allen key clockwise on both top rollers to lock rollers in uppermost position.
(c) Refit the door by first locating the top roller assemblies on the track.
(d) Fit the roller covers.If the door is out of square, adjust as follows:
(a) Unlock the roller assemblies
(b) Adjust the door as required.
(c) Lock the roller assemblies.
(d) Fit the chrome covers.(a) Unlock the bottom roller assemblies.
(b) Move the bottom roller assemblies up or down until they locate correctly in the bottom track and release correctly using the roller release buttons.
(c) Lock the bottom roller assemblies.
(d) Fit the chrome covers.(a) Fit the seals to the side of the doors.
(b) Fit the magnetic seals to the doors making sue they lock correctly.(a) Apply sealant in accordance with the sealant manufacturers instructions along the outside surfaces of the door frame only.
(b) Allow the silicone sealant to cure for 24 hours before use.
(c) Fit the plastic covers to the top of the extrusions.

MAINTENANCE

General Maintenance
Providing the shower enclosure has been correctly installed and is operated in accordance with the instructions contained in this guide, difficulties should not arise.
If any maintenance is required then it must be carried out by a competent tradesperson to whom the maintenance instructions are provided.
Before replacing any parts ensure the underlying cause of the malfunction has been resolved.
Cleaning
Warning! The use of grout/tile cleaners, scale removers, abrasive scourers, drain unblockers and other powerful detergents may lead to damage of metallic, plated and plastic surfaces, including the tray and shower waste.
Avoid the use of ‘spray and leave’ cleaners. Any cleaner used should have a pH level between 4 and 8 and immediately wiped dry using a soft cloth.
Care
To preserve the beauty of your shower enclosure for many years, please observe the following care instructions:
Rinse glass and frame with clear water after showering. Remove water droplets with a squeegee. Do not rub dry! To clean your shower hygienically and easily, we recommend the use of a biodegradable cleanser.
Regular cleansing with a biodegradable cleanser prevents stubborn stains and ensures a clean and hygienic surface for many years. Do not use scouring or caustic cleansers under any circumstances! These can damage the surface of the frame, glass and decorative parts as well as the plastic parts.
Chrome Parts
Use only cleansers expressly specified for chrome!
KOHLER Glass Cleaner
For occasional cleaning of glass treated with KOHLER Glass Protector or for more regular maintenance of untreated surfaces, we recommend using KOHLER Glass Cleaner.
The cleaner cleans and polishes without smearing or streaking and rejuvenates the Glass Protector.

SPARE PARTS

enclosures-1470-0000) Door Spare
10| 305818| Glass Cleaner

DECLARATION OF PERFORMANCE

DECLARATION OF PERFORMANCE

Brand name:| Mira|
---|---|---
Product name:| Leap Shower Enclosures|
Product Range:| Leap Pivot Door,
Leap Sliding Door,
Leap Quadrant Enclosure
Leap Walk in Enclosure,
Leap Extended Sliding Door | Leap Bi-Fold Door
Leap Side Panel
Leap Pentagon Enclosure,
Leap Double Door Slider
Product type:| Domestic Shower Enclosure   
Manufacturer:| Kohler Mira Ltd
Cromwell Road, Cheltenham
Gloucestershire GL52 5EP
United Kingdom.|
Directives:| EU 305/2011| Construction Products Regulations
System of   assessment:| System 4:
Type testing / Factory production Control|
Standards:| EN 14428:2004 +A1:2008.
Shower enclosures – Functional requirements and test methods.|
Essential Characteristics| Performance| Harmonised technical specification
---|---|---
IR-CA-DA| Compliant| EN 14428:2004 +A1:2008

The performance of the products described above, are in conformity with the relevant community harmonisation legislation.
This declaration of performance is issued under the sole responsibility of Kohler Mira Ltd.
Signed for and on behalf of Kohler Mira Ltd.

Signature:|
---|---
Name:| Andrew Baines
Place:| Cheltenham, UK
Doc. No.:| CE 0099

14

CUSTOMER SERVICE

Guarantee
Your enclosure has the benefit of our lifetime guarantee which starts from the date of purchase. This guarantee only applies in the United Kingdon and the Republic of Ireland.
To activate this guarantee, you must return your completed registration card with a copy of proof of purchase from an approved Mira retailer within 30 days of purchase.
This guarantee is in addition to your statutory rights and is subject to conditions (see registration card).
What to do if something goes wrong
If your product does not function correctly when you first use it, contact your installer to check that it is installed in accordance with the instructions in this manual.
If this does not resolve the issue, contact our Customer Services Team who will offer you or your installer help and advice.

| Helpdesk Service
Our Customer Services Team is comprehensivelytrained and can offer help and advice, spare
parts, accessories or a service visit.
We will need you to have your model name, model number and date of purchase.
---|---
| Mira Showers Website (www.mirashowers.co.uk)
From our website you can r egister your guarantee, download additional user guides, diagnose faults, purchase our full range of accessories and popular spares, refer to our FAQ’s and request a service visit.
| Spares and Accessories
We hold the largest stocks of genuine Mira sparesand accessories.
Contact us for a price and to purchase spares or accessories (Only available in the UnitedKingdom).
| Service / Repairs
No one knows our products better than our nationwide team of Service Te chnicians. We can carry out service or repair work to your product both during and after the guarantee period (Only available in the United Kingdom and the Republic of Ireland).

Ask about our fi xed price service repairs.
To Contact Us: UK

| 0844 571 5000
Please note: Calls cost 7p per minute plus your phone company’s access charge.
---|---
| 01242 282595
| Email – Visit www.mirashowers.co.uk/contactus
| By Post:
Mira Customer Services Dept, Cromwell Road, Cheltenham, Gloucestershire, GL52 5EP

To Contact Us: Eire Only
01 531 9337
Email – CustomerServiceEire@mirashowers.com

14

Kohler Mira Ltd, Cromwell Road, Cheltenham, Gloucestershire
GL52 5EP, UK.
Kohler.
Leap Range of Domestic Shower Enclosures.
Declaration of Performance: CE 0099
Pivot Door, Bi-Fold Door, Sliding Door, Side Panel, Quadrant Enclosure, Pentagon Enclosure, Walk in Enclosure, Double Door Slider, Extended Sliding Door.

Mira is a registered trade mark of Kohler Mira Limited.
The company reserves the right to alter product specifi cations without notice.

Check out our full range of Shower Enclosures
Quadrant Shower Enclosures
Corner Entry Shower Enclosures
Walk in Shower Enclosures
Sliding Shower Doors
Bifold Shower Doors
Pivot Shower Doors
Hinged Shower Doors
Shower Screens

From Top Brands

Coram Shower Enclosures
Mira Shower Enclosures
Hydrolux Shower Enclosures
Diamond Shower Enclosures

With qualityshower trays to match your enclosure

Square Shower Trays
Rectangular Shower Trays
Quadrant Shower Trays
Coram Shower Trays
Mira Flight Shower Trays

References

• Contact Us | Help & Support by Mira Showers
• Shower Enclosures | Shower Cubicles - Plumbworld
• Shower Enclosures | Shower Cubicles - Plumbworld
• Shower Trays - Plumbworld
• Corner Entry Shower Enclosures - Plumbworld
• Shower Enclosures | Shower Cubicles - Plumbworld
• Mira Shower Trays - Plumbworld
• Shower Enclosures | Shower Cubicles - Plumbworld
• Quadrant Shower Enclosures - Plumbworld
• Shower Enclosures | Shower Cubicles - Plumbworld
• Shower Screens | Over Bath Shower Screens | Plumbworld - Plumbworld
• Shower Enclosures | Shower Cubicles - Plumbworld
• Walk In Showers - Plumbworld

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>