AERO 360 Cecotec Ceiling Fan Instruction Manual

AERO 360 Cecotec Ceiling Fan

FAQs

• Q: Can this ceiling fan be used in commercial settings?
  • A: No, this device is designed for domestic use only and should not be used in bars, restaurants, farmhouses, hotels, motels, etc.
• Q: What should I do if the fan blades are making noise?
  • A: Check if the blades are properly installed and tightened. Loose blades can cause noise. If the issue persists, contact technical support for further assistance.
• Q: How often should I clean the ceiling fan?
  • A: It is recommended to clean the fan regularly, at least once every few months, to ensure optimal performance and air quality.

PARTS AND COMPONENTS

Fig. 1

1. Installation bracket
2. Hanging ball
3. Downrod
4. Screws I
5. Canopy
6. Screws II
7. Clevis pin
8. Mounting plate
9. Motor
10. Nut and washer
11. Blades
12. Blade bracket
13. Screws III
14. Light base plate
15. Lamp support
16. Lamp holder
17. Lamp

NOTE: The graphics in this manual are schematic representations and may not exactly match the device.

BEFORE USE

• This appliance is packaged in a way as to protect it during transport. Take the device out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place.
• This will help you prevent damage to the device when transporting it in the future.
• In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
• Make sure all parts and components are included and in good condition. If there is any piece missing or not in good condition, immediately contact the official Cecotec Technical Support Service.
• Carefully open the ceiling fan’s box, take all the components out, and place them on a cloth or soft surface to avoid damage. Do not lay the motor’s box on its sides to avoid damage to the housing.

PRODUCT ASSEMBLY

The following tools are required to carry out the installation: screwdriver, flat-head screwdriver, adjustable pliers or wrench, stepladder, wire cutter, epoxy resin, and rated electrical tape.

Warning

• To avoid electric shocks, turn the household power supply off before installing the ceiling fan.

General assembly instructions

• If you hang the fan on a hook, the latter must withstand at least 100 kg.

Assembly according to the type of ceiling. (Fig. 2):

1. Low ceilings
2. Normal ceilings
3. Sloped ceilings (might require a longer downrod, not supplied by Cecotec)

To assemble this ceiling fan, follow the steps below (Fig. 3-12):

1. Remove the lower and upper pins from the downrod and release the hanging ball at the top of the rod.
2. Pass the wiring from the main body through the downrod.
3. Attach the downrod to the main body by inserting the pin through the downrod and the main-body attachment. Tighten the screws provided on the main-body attachment to properly secure the downrod.
4. Remove the 4 screws that fix the upper canopy and the installation bracket. Insert the upper canopy through the downrod. Fig. 3
5. Insert the pin through the pin holes located on the upper end of the downrod. Once inserted, slide the hanging ball upward to the upper end of the downrod and fix it with one of the screws provided.
6. Make sure the pin fits in the slots located inside the hanging ball before screwing it.
7. Mark the center of the installation bracket and use both self-tapping screws provided with their corresponding washers and pressure washers to fix the installation bracket to a wooden ceiling.
   • Warning: Self-tapping screws are only suitable for wooden ceilings. In the case of installing the ceiling fan to concrete ceilings or joists, use a drill for making the holes and plugs or expansion screws (not included).
8. Remove the screws located on the lower part of the motor through the lamp support.
9. Screw the blade brackets to the motor through the hole in the lamp support paying attention to the warning sticker located on one of the blade brackets. Fig. 4
10. Screw the blades to the blade brackets using the screws, washers, and nuts provided. Because blades are reversible, choose the side you wish to be visible and screw them in such way that the nuts are located on the top part of the blade. Fig. 5
11. Once the installation bracket is screwed, connect the wiring. First, connect the quick-connect cable to the terminal block on the installation bracket. Following the color code (Fig. 6). From the opposite end of the terminal block, connect the wiring from the installation of your home.

Fig. 6 key:

1. Black and Blue

2. White

3. Earth

4. Phase (Brown/Black)

5. Neutral (Blue)

6. Earth

7. Lift the pre-assembled fan assembly to the installation bracket and pass the hanging ball through the hole in the installation bracket. Fig.7

8. Connect the cables that come out from the downrod to those from the installation bracket using both quick connectors.

9. Slide the canopy upwards so that all the connections are stored inside it and screw it to the installation bracket using the 4 screws (2 to each side) removed at the beginning of the installation process. Fig. 8

10. Tighten the bulb to the lamp holder (not included). Fig. 9

11. Place the lamp on the bottom of the appliance inserting the tabs of the lamp support into the glass so that it is fully secured. Fig. 10

12. Attach the chain. To do so, fix the long chains with the corresponding end parts of the fan chains by introducing the long chain end into the connecting piece. Fig. 11

13. Make sure that the chains are safely fixed by pulling on them carefully from the connecting piece. Fig. 11

Please note: The reversible blades have 2 different high-quality finishes. By inverting the blades, the appliance produces a decorative effect and adapts to different room designs.
Warning: The important safety precautions and instructions stated in this manual are not meant to cover all possible conditions and situations that may occur. Bear in mind that common sense and caution are necessary factors in the installation and operation of this fan.

OPERATION

To switch the fan on or off

• When it is turned off (OFF position), pull from the switch chain until the fan turns on. To switch it off, pull from the chain again.
• Function sequence from OFF position:
• Pull 1 time for high speed.
• Pull again: medium speed.
• Pull once more: low speed.
• Pull one last time to turn it off.

Winter/summer function. Fig.12

The switch on the fan body is a switch that moves to the left or right depending on the desired function, it is used to change the rotation direction (clockwise or counterclockwise) of the fan blades.

• Winter function: move the commutator to the clockwise position. The blades will start to rotate clockwise, causing warm air to be distributed throughout the room.
• Summer function: move the commutator to the counterclockwise position. The blades will start rotating counterclockwise, causing fresh air to be distributed throughout the room.
• Warning: Before using the commutator, turn the fan off and make sure it has completely stopped moving to avoid personal and product damage.

CLEANING AND MAINTENANCE

NOTE:

• Make sure to disconnect the fan before cleaning it.
• Do not immerse any of the parts of the device in water or splash them with any other liquid.

Replacing the light bulb

• Turn the appliance off (preferably, turn it off at the power circuit breaker) and wait until it cools down. (Be careful, the bulbs can reach very high temperatures during use).
• Remove the bulb by holding it firmly and turning it counterclockwise. To do this, hold it firmly and turn it counterclockwise.
• Take a new bulb and put it carefully into the lamp holder. Screw it clockwise.
• Turn the power supply on again and switch the lamp on.

Important: This fan uses 1 E27 / Max bulb. 60 W (not included)

Cleaning

• Unplug the fan and allow it to cool down before cleaning it.
• Never immerse the fan in water or other liquids.
• Clean with a soft, dry cloth.
• Do not use any cleaning chemicals such as detergents and abrasives.
• Do not allow water to come into contact with any of the electrical parts of the appliance.
• Do not use a wet cloth to clean the motor. Keep the fan clean and store it in a dry place to avoid moisture if you’re not going to use it for some time.
• We recommend using neutral detergent and a soft cloth. Do not use solvents, acid detergents, petrol, alcohol, etc. to clean the plastic parts, as they may be damaged.
• Do not allow water to enter the motor or touch the cable during cleaning.

TROUBLESHOOTING

If the fan does not turn on:

• Check the fuses or circuit breakers at the electric panel.
• Check the fan cables.
• Warning: make sure the main supply is off
• Make sure that the commutator is firmly in position. The fan will not work if the switch is in the middle position.
• If the fan does not work, please contact the official Cecotec Technical Support Service. Do not try to repair the internal electric connections.

If the fan makes a lot of noise:

• Check that all screws on the motor housing are properly fixed (do not overtighten them).
• Check that the screws fixing the blade bracket are tight enough.
• Allow the fan to run for 24 hours. Most of the noises produced by the fan will disappear after this time.

If the fan oscillates:

• Ensure that all blades are firmly screwed to the blade brackets.
• Check that all blade brackets are firmly fixed to the motor.
• Make sure that the mounting bracket is firmly fixed to the ceiling.

If the light does not work:

• Check if the bulb is defective.
• Make sure that the electric connections are correct.
• If the problem persists, contact the official Technical Support Service of Cecotec.

TECHNICAL SPECIFICATIONS

• Product: EnergySilence Aero 360/ EnergySilence Aero 360 Color Full/ EnergySilence Aero 365 White&Wood/ EnergySilence Aero 360 Black&Wood/ EnergySilence Aero 365 Black&Wood/ EnergySilence Aero 360 Gold&Wood/ EnergySilence Aero 365 Gold&Wood
• Product reference: 05939, 08366, 08367, 08368, 08369, 08370, 08371
• Rated power: 50 W
• Voltage: 220-240 V~
• Frequency: 50 Hz 1 E27 60 W max bulb (NOT INCLUDED)
• MODEL
  • ENERGYSILENCE AERO 360
  • ENERGYSILENCE AERO 360 COLORFUL
  • ENERGYSILENCE AERO 365 WHITE&WOOD
  • ENERGYSILENCE AERO 360 BLACK&WOOD
  • ENERGYSILENCE AERO 365 BLACK&WOOD
  • ENERGYSILENCE AERO 360 GOLD&WOOD
  • ENERGYSILENCE AERO 365 GOLD&WOOD

Reyes Católicos nº60, 46910, Alfafar, Valencia (Spain)

The appliance power consumption when off is 0.0 W, following the guidelines of EN 50564:2011 and the European regulations 1275/2008/EC and 801/2013/EC. For this purpose, the device is connected to the mains without performing any function. The switch/knob of the appliance was set to the Off position. Technical specifications may change without prior notification to improve product quality. Made in China | Designed in Spain

DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC APPLIANCES

• This symbol indicates that, according to the applicable regulations, the product and/or batteries must be disposed of separately from household waste.
• When this product reaches the end of its shelf life, you should dispose of the batteries/accumulators and take them to a collection point designated by the local authorities.
• Consumers must contact their local authorities or retailers for information concerning the correct disposal of old appliances and/or their batteries. Compliance with the above guidelines will help protect the environment.

WARRANTY

TECHNICAL SUPPORT AND WARRANTY

• Cecotec shall be liable to the end-user or consumer for any lack of conformity that exists at the time of delivery of the product under the terms, conditions, and deadlines established by the applicable regulations.
• It is recommended that repairs be carried out by qualified personnel.
• If at any moment you detect any problem with your product or have any doubts, do not hesitate to contact the official Cecotec Technical Support Service at +34 96 321 07 28.

COPYRIGHT

• The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L.
• All rights reserved. The contents of this publication may not, in whole or in part, be reproduced, stored in a retrieval system, transmitted, or distributed by any means (electronic, mechanical, photocopying, recording, or similar) without the prior authorization of CECOTEC INNOVACIONES, S.L.

CONTACT INFORMATION

• www.cecotec.es.
• Cecotec Innovaciones S.L.
• Av. Reyes Católicos, 60
• 46910, Alfafar (Valencia)
• AP02231227

References

• Cecotec Tienda Oficial | Envío Gratis | Mejor Precio

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>