milwaukee M18 FUEL One Key Hammer Drill User Manual

: August 24, 2024
: Milwaukee

Table of Contents

milwaukee M18 FUEL One Key Hammer Drill
PRODUCT DESCARIPATION
Specifications
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

milwaukee M18 FUEL One Key Hammer Drill

Only maintenance, service, repairs, and replacements of parts as defined in the Operator’s Manual can be performed by the user. All other repairs are to ONLY be performed by personnel authorized by MILWAUKEE TOOL. Do not attempt to install other parts; this COULD void your tool warranty.

For service, parts, or inquiries, contact us

Customer Service at 1.800.SAWDUST (1.800.729.3878)
E-Service tool repair at: www.milwaukeetool.com/e-service
Find a local authorized MILWAUKEE service location at Milwaukeetool.com
Find a MILWAUKEE factory Service Center Location or MILWAUKEE factory Central Repair Center at Milwaukeetool.com. Send the following, posted paid and insured:
Your name, address, and phone number
Description of the issues
Copy of the proof of purchase
Tool, charger, and batteries involved with the issues

MILWAUKEE factory Central Repair Centers:

MILWAUKEE TOOL Central Repair 1401 Sycamore Avenue Greenwood, MS 38930 MILWAUKEE TOOL Central Repair 2198 Southtech Drive Greenwood, IN 46143 MILWAUKEE TOOL l www.milwaukeetool.com 13135 W. LISBON RD., BROOKFIELD, WI 53005

EXAMPLE:
Component Parts (Small #) Are Included When Ordering The Assembly (Large #).

PRODUCT DESCARIPATION

REMOVING THE CHUCK SCREW:
Set the Speed Selector Slide (39) to the #1 setting. With the aid of a small pencil tip torch (or use an air reduction nozzle on a heat gun) apply heat into the chuck opening, directly to the head of reversing screw just prior to removing the screw. Place a T40 1/4” torx bit into the head of the reversing screw and place a 1/4” boxed end wrench over the hex on the T40 bit. It is recommended to use a 12”-18” metal tube or pipe as leverage over the boxed wrench. In a clockwise direction apply a slow, steady force on the ‘cheater bar’ to break the screw loose.

REMOVING THE KEYLESS CHUCK:
Tighten a 3/8” or 10mm Allen Key into the jaws of the chuck. Place the tool into a vise with soft jaws (this will require that you remove the belt clip from the tool). It is recommended to use a 12”-18” metal tube or pipe as leverage over the allen key. In a counter-clockwise direction apply a slow, steady force on the ‘cheater bar’ to break the chuck loose.

INSTALLING NEW CHUCK AND SCREW
Torque Chuck to 1095 kgf-cm (950.418 lb-in or 79.20 lb-ft) Torque Screw to 400 kgf-cm (347 lb-in or 28.93 lb-ft)

FIG. PART NO. DESCRIPTION OF PART NO. REQ.

1 05-88-0019 M8.0 x 1 LH T-40 Chuck Screw (1)
13 06-82-7337 M3 x 20mm Pan Hd. T-10 Screw w/Washer (4)
15 45-24-1045 Shift Spring (1)
16 42-42-3001 Forward/Reverse Shuttle (1)
20 ————— Left Housing Halve – Support (1)
21 ————— Coin Cell Board Assembly (1)
22 ————— 3V Coin Cell Battery (CR 2032) (1)
23 31-15-0011 Coin Cell Cover (1)
24 05-81-1100 M2.6 x 6mm ST Phillips Screw (2)
25 ————— Belt Clip (1)
26 06-82-2500 6-32 x 7mm Pan Hd. Slt. T-15 Mach. Screw (2)
34 06-82-7336 M3 x 20mm Pan Hd. ST T-10 Screw (4)
39 44-10-4002 Speed Selector Slide (1)
40 40-50-9001 Detent Spring (1)
41 ————— Right Housing Halve – Cover (1)
43 ————— Bit Holder Housing (1)
44 06-82-6350 M3 x 16mm Pan Hd. ST T-10 Screw (5)
45 06-82-2367 M3 x 38mmPan Hd. ST T-10 Screw (2)
46 42-55-9005 Blow Molded Carrying Case (1)
48 12-20-0478 Service Nameplate (1)
49 10-20-1048 Warning Label (1)
50 43-72-0950 Bit Holder Kit (1)
51 31-44-2806 Housing Kit (1)
52 42-70-0950 Belt Clip Kit (1)
53 14-29-1014 Gearcase Assembly (1)
54 16-07-1016 Rotor Assembly (1)
55 14-20-2806 Electronic Assembly (1)
56 42-62-1002 Side Handle Assembly (1)
57 42-66-0030 1/2” Keyless Chuck (1)
58 45-24-2806 Wireless Selector Kit (1)
59 14-20-0068 Coin Cell Board Assembly with Battery (1)

Be sure that all mechanical and electrical components are placed firmly and squarely in the corresponding cavities of left housing halve. Be very careful and make sure that all wires and the wire ribbon are placed firmly down in wire channels and traps. Make sure there are no interferences when installing the right housing halve.

Specifications

Product Name : M18 FUEL One-Key Hammer-Drill
Catalog Number : 2806-20
Chuck Size : 1/2 inch
Chuck Type : Keyless
Power Source : Cordless Battery
Maximum Torque: Not specified
Weight : Not specified

FAQ

Q: Can I perform all repairs on the tool myself?
A: Only maintenance, service, repairs, and replacements as defined in the Operator’s Manual can be done by the user. All other repairs should be done by authorized personnel only.

Q: Where can I find Milwaukee Tool Central Repair Centers?
A: You can find MILWAUKEE factory Central Repair Centers at the following locations: