ASUS RTX4070S-O12G Axial-tech Fan Design Quick Start Guide

ASUS RTX4070S-O12G Axial-tech Fan Design

SYSTEM SPECIFICATIONS

Thank you for choosing the NVIDIA® GeForce RTXTM 4070 graphics card. Before you begin, please review the following System Specifications to ensure your PC has the appropriate hardware and software for your new graphics card.

System Specifications

• Motherboard: PCI Express® graphics slot required.
• Clearance: Must have space for 244mm (L) x 112mm (W) x 41mm (H) card. One additional slot clearance in front of the fans is recommended for better airflow.
• System Power Supply:
  • 650 W power rating minimum.
  • Supported power connector configurations:
  • At least two PCIe 8-pin cables (with RTX 4070 PCIe Gen 5 Power Connector Adapter).
  • One 300 W or greater PCIe Gen 5 Cable (16-pin).
• Operating System:
  • Microsoft® Windows® 11 64-bit recommended, or Microsoft® Windows® 10 64-bit April 2018 Update v1803 or newer.
  • Linux, 64-bit.
• Driver Installation: 2 GB of available disk space required for driver installation.

EQUIPMENT

The following equipment is included in the NVIDIA GeForce RTX 4070 graphics card box.

Attention: Use only the included NVIDIA power connector adapter for your GeForce RTX 40 Series Founders Edition graphics card.

HARDWARE INSTALLATION

1. Turn off your computer, disconnect the power cord and remove any existing graphics card(s).
   Attention: It is very important that you wait until the graphics card has cooled before taking the card out of the system.

2. Remove two slot covers if there was no existing graphics card.
   Remove two adjacent slot covers that correspond to the PCI Express slot you are installing the graphics card in.

3. Connect the 16-pin plug of NVIDIA power connector adapter to the power receptacle on the top of the GeForce RTX 4070 graphics card.
   Connect at least two independent dedicated cables with 8-pin PCI Express plugs from the system power supply to the NVIDIA power connector adapter.
   Attention: Use only the included NVIDIA power connector adapter for your GeForce RTX 40 Series Founders Edition graphics card.
   To help ensure the connector is secure we recommend plugging the power dongle into the graphics card first to ensure it’s firmly and evenly plugged in, before plugging the graphics card into the motherboard.
   Attention: Ensure the power plug is fully inserted and seated flush against the power receptacle.

4. Install the GeForce RTX 4070 graphics card into the primary PCI Express x16 slot on your motherboard. Install your GeForce RTX 4070 into the Primary PCI Express x16 slot (the Primary slot is the one closest to the CPU).
   Attention: This GPU card should not be installed with the I/O brackets facing downwards.

5. Reinstall the covers on your computer and reconnect any cables previously removed.

CONNECTING TO THE DISPLAY

1. Connect the display(s) to the graphics card.
2. Reconnect your power cord to the PC.

SOFTWARE INSTALLATION AND CONFIGURATION

With the hardware installed, the final step is to install the GeForce Experience software to update your drivers and optimize your games.

1. Download and install GeForce Experience software.

   • Go to http://www.geforce.com/geforce-experience and click Download Now.
   • Accept the NVIDIA software license agreement by selecting Agree and Continue. GeForce Experience software begins to install.
   • Select Close to finish the installation.

2. Optimize your installed games.

   • Open GeForce Experience and click Scan for Games and click OK to scan your installed games.
   • Click on Optimize All to optimize your game settings.

3. Get the latest drivers.

   • Open GeForce Experience, log in, and select the Drivers tab.

   • Select Download Driver. Your GPU driver begins to download.

   • Select Express Installation when the download finishes. GeForce Experience begins to install the graphics driver.
     Note: It may take several minutes for the installation to take place. Your screen may go blank for a few seconds one or more times during installation. This is normal.

   • Click CLOSE when the driver install completes.

4. Congratulations! Your GeForce graphics card is now ready to use!
   Note: If you have any questions about your NVIDIA product you can Chat live with NVIDIA Customer Care at www.nvidia.com/support or call 1-800-797-6530 (US) or 0800 404 7747 (UK)

COMPLIANCES

The NVIDIA GeForce RTX 4070 graphics card (Compliance Model: PG141C) is compliant with the following regulations:

• Federal Communications Commission (FCC)
• Underwriters Laboratories (UL)
• Innovation, Science and Economic Development Canada (ISED)
• European Conformity; Conformité Européenne (CE)
• Australian Communications and Media Authority (RCM)
• UK Conformity Assessed (UKCA)
• Voluntary Control Council for Interference (VCCI)
• Korea Certification (KC)
• Bureau of Standards, Metrology & Inspection (BSMI)
• Ukraine Technical Regulations (UA TR)
• Moroccan regulatory framework (CMIM)

UNITED STATES

Federal Communications Commission (FCC)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including any interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  FCC Warning: The FCC requires that you be notified that any changes or modifications to this device not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Underwriters Laboratories (UL)
CANADA
Innovation, Science and Economic Development Canada (ISED) CAN ICES-003(B)/NMB-003(B)
This device complies with Innovation, Science and Economic Development Canada (ISED) license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

EUROPEAN UNION
European Conformity
Santa Clara, California, USA
This device bears the CE mark accordance with Directive 2014/30/EU and 2011/65/EU.

This device complies with the following Directives:

• EMC Directive 2014/30/EU
• RoHS Directive 2011/65/EU for hazardous substances
  A copy of the Declaration of Conformity to the essential requirements may be obtained directly from NVIDIA GmbH (Bavaria Towers – Blue Tower, Einsteinstrasse 172, D-81677 Munich Germany).

AUSTRALIA AND NEW ZEALAND
Australian Communications and Media Authority (RCM)
This product meets the applicable EMC requirements for Class B, I.T.E equipment and applicable radio equipment requirements

GREAT BRITAIN (ENGLAND, WALES AND SCOTLAND)
UK Conformity Assessed (UKCA)
This device complies with the following Regulations:

• SI 2016/1091: Electromagnetic Compatibility (EMC)
• SI 2012/3032: The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (As Amended).

A copy of the Declaration of Conformity to the essential requirements may be obtained directly from NVIDIA Ltd. (100 Brook Drive, 3rd Floor Green Park, Reading RG2 6UJ, United Kingdom).

Japan RoHS Material Content Declaration

A Japanese regulatory requirement, defined by specification JIS C 0950: 2008, mandates that manufacturers provide Material Content Declarations for certain categories of electronic products offered for sale after July 1, 2006.

Product Model Number: Graphic card

Major Classification

| Symbols of Specified Chemical Substance
Pb| Hg| Cd| Cr(VI)| PBB| PBDE
PCB| 0| 0| 0| 0| 0| 0
Passive components| Exempt| 0| 0| 0| 0| 0

Active components| Exempt| 0| 0| 0| 0| 0
Processor| 0| 0| 0| 0| 0| 0
Memory| 0| 0| 0| 0| 0| 0
Mechanicals| Exempt| 0| 0| 0| 0| 0
Cables/Connectors| 0| 0| 0| 0| 0| 0
Soldering material| 0| 0| 0| 0| 0| 0
Flux, Solder Paste, label and other consumable materials| 0| 0| 0| 0| 0| 0

Notes:

1.       “0” indicates that the level of the specified chemical substance is less than the threshold level specified in the standard, JIS C 0950: 2008.

2.       “Exempt” indicates that the specified chemical substance is exempt from marking and it is not required to display the marking for that specified chemical substance per the standard, JIS C 0950: 2008.

3.       “Exceeding 0.1wt%” or “Exceeding 0.01wt%” is entered in the table if the level of the specified chemical substance exceeds the threshold level specified in the standard, JIS C 0950: 2008.

Korea RoHS Material Content Declaration

NVIDIA has evaluated and confirmed that the products comply with the standards for the content of hazardous substances in accordance with Article 3 of the ‘Act on Resource Circulation of Electrical and Electronic Equipment and Vehicles’ pursuant to the Enforcement Regulations of Article 11, Paragraph 1 in the statute.

Attachment: None

*Preparing the Form

① Please indicate the product category according to the categories listed in Article 8, Items 1and 2 of the ‘

Enforcement Ordinance of the Statute on the Recycling of Electrical, Electronic and Automobile Materials’

② For electrical and electronic products, please indicate the Model Name (and number). For automobiles, please

indicate the Vehicle Identification Number.

③ Please indicate the name of manufacturer and/or importer of the product.

Bureau of Standards, Metrology & Inspection (BSMI) 

Taiwan RoHS Material Content Declaration

Declaration of the presence condition of the Restricted Substances Marking

Equipment Name: Graphic Card
Parts| Restricted substances and its chemical symbols
(Pb )| (Hg)| (Cd)| (Cr(VI))| (PBB)| (PBDE)
PCB| O| O| O| O| O| O
---|---|---|---|---|---|---
Passive components| –| O| O| O| O| O
Active components| –| O| O| O| O| O
Processor| O| O| O| O| O| O
Memory| O| O| O| O| O| O
Mechanical parts and Fan| –| O| O| O| O| O
Cables/Connectors| O| O| O| O| O| O
Soldering material| O| O| O| O| O| O
Flux, Solder Paste, label and other consumable materials| ****

O

| ****

O

| ****

O

| ****

O

| ****

O

| ****

O

The table according to SJ/T 11364

• O: Indicates that this hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in GB/T 26572.
• X: Indicates that this hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in GB/T 26572.
  All parts named in this table with an “X” are in compliance with the European Union’s RoHS Legislation.

Note: The referenced Environmental Protection Use Period Marking was determined according to normal operating use conditions of the product such as temperature and humidity.

CHINA
China RoHS Material Content Declaration

The Table of Hazardous Substances and their Content as required by Management Methods for Restricted Use of Hazardous Substances in Electrical and Electronic Products

Parts| Hazardous Substances

(Pb)

| ****

(Hg)

| ****

(Cd)

| ****

(Cr(VI))

| ****

(PBB)

| ****

(PBDE)

PCB| O| O| O| O| O| O
Passive components| X| O| O| O| O| O
Active components| X| O| O| O| O| O
Processor| O| O| O| O| O| O
Memory| O| O| O| O| O| O
Mechanical parts and Fan| X| O| O| O| O| O
---|---|---|---|---|---|---
Cable/Connectors| O| O| O| O| O| O
Soldering material| O| O| O| O| O| O
Flux, Solder Paste, label and other consumable materials|

O

|

O

|

O

|

O

|

O

|

O

The table according to SJ/T 11364

• O: Indicates that this hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in GB/T 26572.
• X: Indicates that this hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in GB/T 26572.
  All parts named in this table with an “X” are in compliance with the European Union’s RoHS Legislation.
  Note: The referenced Environmental Protection Use Period Marking was determined according to normal operating use conditions of the product such as temperature and humidity.

INDIA
India RoHS Material Content Declaration
This product, as well as its related consumables and spares, complies with the reduction in hazardous substances provisions of the “India E-waste (Management and Handling) Rule 2016”. It does not contain lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for where allowed pursuant to the exemptions set in Schedule 2 of the Rule.

India RoHS Self-Declaration Form (as per E-Waste (Management) Rules, 2016)

Sr.

No.

|

Product Category& Code (as Per Schedule I of E-Waste (M) Rules, 2016

|

Product name

|

Model No.

|

Product Weight (g)

|

Date of placing on market

|

Compliance with

RoHS Yes/No

|

RoHS

Information provided on product info booklet Yes/No

|

In case Product is imported from other country, name of the country manufactured

i.

| TEW2

(Graphic Card)

|

Graphic Card

|

N/A

|

N/A

|

N/A

|

Yes

|

Yes

|

China

UKRAINE
Ukraine Technical Regulations (UA TR)

MOROCCO
Moroccan regulatory framework (CMIM)

Notice
The information provided in this specification is believed to be accurate and reliable as of the date provided. However, NVIDIA Corporation [“”NVIDIA””) does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information. NVIDIA shall have no liability for the consequences or use of such information or for any infringement of patents or other rights of third parties that may result from its use. This publication supersedes and replaces all other specifications for the product that may have been previously supplied. NVIDIA reserves the right to make corrections, modifications, enhancements, improvements, and other changes to this specification, at any time and/or to discontinue any product or service without notice. Customer should obtain the latest relevant specification before placing orders and should verify that such information is current and complete.
NVIDIA products are sold subject to the NVIDIA standard terms and conditions of sale supplied at the time of order acknowledgment, unless otherwise agreed in an individual sales agreement signed by authorized representatives of NVIDIA and customer. NVIDIA hereby expressly objects to applying any customer general terms and conditions about the purchase of the NVIDIA product referenced in this specification. NVIDIA products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of the NVIDIA product can reasonably be expected to result in personal injury, death or property or environmental damage. NVIDIA accepts no liability for inclusion and/or use of NVIDIA products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk.
NVIDIA makes no representation or warranty that products based on these specifications will be suitable for any specified use without further testing or modification. Testing of all parameters of each product is not necessarily performed by NVIDIA. It is customer’s sole responsibility to ensure the product is suitable and fit for the application planned by the customer and to do the necessary testing for the application in order to avoid a default of the application or the product. Weaknesses in customer’s product designs may affect the quality and reliability of the NVIDIA product and may result in additional or different conditions and/or requirements beyond those contained in this specification. NVIDIA does not accept any liability related to any default, damage, costs or   problem which may be based on or attributable to: [ii the use of the NVIDIA product in any manner that is contrary to this specification, or [ii) customer product designs.
No license, either expressed or implied, is granted under any NVIDIA patent right, copyright, or other NVIDIA intellectual property right under this specification. Information published by NVIDIA regarding third-party products or services does not constitute a license from NVIDIA to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property rights of the third party.
ALL NVIDIA DESIGN SPECIFICATIONS, REFERENCE BOARDS, FILES, DRAWINGS, DIAGNOSTICS, LISTS, AND OTHER DOCUMENTS [TOGETHER AND SEPARATELY, “”MATERIALS””) ARE BEING PROVIDED ··As Is.·· NVIDIA MAKES NO WARRANTIES, EXPRESSED, IMPLIED, STATUTORY, OR OTHERWISE concerning THE MATERIALS, AND EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE. Notwithstanding any damages that the customer might incur for any reason whatsoever, NVIDIA”s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the NVIDIA terms and conditions of sale for the product.

VESA DisplayPort
DisplayPort and DisplayPort Compliance Logo, DisplayPort Compliance Logo for Dual-mode Sources, and DisplayPort Compliance Logo for Active Cables are trademarks owned by the Video Electronics Standards Association in the United States and other countries. HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
OpenCL
OpenCL is a trademark of Apple Inc. used under license to the Khronos Group Inc.
MPEG LA (H.264/AVC)
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO [ii ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD [“”AVC VIDEO””) AND/OR [ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.
MPEGLA.COM.
Trademarks
NVIDIA, the NVIDIA logo, NVIDIA CUDA, NVIDIA GeForce, GeForce RTX, Ge Force Experience, NVIDIA NVLink, GigaThread, Lumenex, PureVideo, and PhysX Technology are trademarks or registered trademarks of NVIDIA Corporation. Other company product names may be trademarks of the respective companies with which they are associated.
Copyright
© 2023 NVIDIA Corporation. All rights reserved.

FAQs

What makes the ASUS RTX4070S-O12G Axial-tech Fan Design unique?

The ASUS RTX4070S-O12G Axial-tech Fan Design features optimized cooling with three advanced fans that have longer blades and a barrier ring to enhance downward air pressure, ensuring efficient cooling during high-performance tasks.

What is the boost clock speed of the ASUS RTX4070S-O12G?

The ASUS RTX4070S-O12G Axial-tech Fan Design has a boost clock speed of 2550 MHz in OC Mode, offering powerful performance for demanding tasks.

How does the Dual BIOS feature work on the ASUS RTX4070S-O12G?

The ASUS RTX4070S-O12G Axial-tech Fan Design includes a Dual BIOS feature that allows users to switch between Performance Mode for maximum speed and Quiet Mode for reduced noise during lighter workloads.

What kind of memory does the ASUS RTX4070S-O12G come with?

The ASUS RTX4070S-O12G Axial-tech Fan Design is equipped with 12 GB of GDDR6X memory, providing ample bandwidth for high-resolution gaming and professional workloads.

What is the power requirement for the ASUS RTX4070S-O12G?

The ASUS RTX4070S-O12G Axial-tech Fan Design requires a 240-volt power supply and features two 8-pin power connectors to ensure stable power delivery.

What resolution can the ASUS RTX4070S-O12G support?

The ASUS RTX4070S-O12G Axial-tech Fan Design supports a maximum screen resolution of 7680 x 4320 pixels, making it capable of handling 8K displays.

What cooling technology is used in the ASUS RTX4070S-O12G?

The ASUS RTX4070S-O12G Axial-tech Fan Design utilizes the Axial-tech fan design with a smaller hub, longer blades, and a barrier ring, all of which contribute to enhanced cooling performance.

What are the dimensions of the ASUS RTX4070S-O12G?

The ASUS RTX4070S-O12G Axial-tech Fan Design has product dimensions of 10.5 x 5.3 x 0.1 inches, making it a compact yet powerful option for high-performance builds.

How does the 0dB technology benefit the ASUS RTX4070S-O12G?

The 0dB technology in the ASUS RTX4070S-O12G Axial-tech Fan Design allows the fans to stop completely during low-temperature operations, ensuring silent performance during light gaming or general use.

What is the chipset brand used in the ASUS RTX4070S-O12G?

The ASUS RTX4070S-O12G Axial-tech Fan Design is built on the NVIDIA chipset, featuring the NVIDIA GeForce RTX 4070 SUPER for superior graphics performance.

Download this Manual:ASUS RTX4070S-O12G Axial-tech Fan Design Quick Start Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>