Dirtdevil 961152313-R0 8 Gallon Wet Dry Vacuum Instruction Manual

Dirtdevil 961152313-R0 8 Gallon Wet Dry

Specifications:

• Product: Wet/Dry Vacuum
• Capacity: 8 Gallons
• Intended Use: Household
• Power: 110V-120V

Product Usage Instructions

General Assembly:

Fully assemble the product before use.

WARNING: Do not plug in the power cord to the outlet before assembly. Use a Philips head screwdriver for assembly.

1. Turn the collection tank upside down.
2. Insert the four caster feet into the slots on the collection tank and tighten with supplied screws.
3. Verify that the casters are mounted correctly. Do not over-tighten the screws.

Extension Cord Usage:

Refer to the following table for the required A.W.G. wire size when using an extension cord with the Wet/Dry Vac:

FAQ:

Q: Can this Wet/Dry Vacuum be used commercially?
A: No, this product is intended for household use only. Commercial use will void the warranty.

Q: What should I do before assembling the Wet/Dry Vac?
A: Make sure the power cord is disconnected from the outlet and use a Philips head screwdriver for assembly.

Q: Can I use any extension cord with the Wet/Dry Vac?
A: Only use extension cords that are rated for outdoor use and refer to the provided table for the required A.W.G. wire size based on the length of the extension cord.

IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USE.

This product is intended for Household use only. If used Commercially warranty is VOID.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS
READ ALL SAFETY WARNINGS AND INSTRUCTIONS BEFORE USING THIS PRODUCT.

WARNING: To reduce the risk of fire,electric shock, or injury:

• Do not run vac unattended.

• Do not vacuum, or use this Wet/Dry Vac
  near flammable liquids, gases, or explosive vapors like gasoline or other fuels, lighter fluids, cleaners, oil-based paints, natural gas, hydrogen, or explosive dusts like coal dust, magnesium dust, grain dust, or gun power. Sparks inside the motor can ignite flammable vapors or dust.

• Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Keep cord away from heated surfaces.

• Do not expose to rain. Store indoors.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not use with damaged cord, plug, or other parts.

• If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.

• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners.

• Do not run Wet/Dry Vac over cord.

• Do not handle plug or the Wet/Dry Vac with wet hands.

• To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials.

• Do not use or store near hazardous materials.

• Do not use this Wet/Dry Vac with a torn filter or without the filter installed except when vacuuming liquids as described in the operation section of this manual.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter.

• Do not leave Wet/Dry Vac unattended when plugged in. Unplug from outlet when not in use and before servicing.

• Turn off Wet/Dry Vac before unplugging.

• Do not put any object into ventilation openings. Do not vacuum with any ventilation openings blocked; keep free of dust, lint, hair, or anything that may reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• To reduce the risk of falls, use extra care when cleaning on stairs.

• Unplug before connecting hose.

• Use only as described in this manual. Use only manufacturer’s recommended attachments.

• This appliance is provided with double insulation. Use only identical replacement parts. SEE DOUBLE INSULATION INSTRUCTIONS.

WHEN USING AS BLOWER:

• Direct air discharge only at work area.
• Do not use Wet/Dry Vac as a sprayer.
• Do not direct air at bystanders.
• Keep children away when blowing.
• Use safety goggles.

This Wet/Dry Vac is double-insulated, eliminating the need for a separate grounding system. Use only identical replacements parts. Read the instructions for Servicing Double-Insulated Wet/Dry Vacs before servicing. Use this Wet/Dry Vac as described in this manual. Observe the following warnings that appear on the motor housing of your Wet/Dry Vac.

DOUBLE INSULATED – Grounding not required – When servicing use only identical replacement parts.

WARNING: To reduce the risk of electric shock-do not expose to rain. Store indoors.

WARNING: Servicing of double-insulated wet/dry vacuum with a double- insulated wet/dry vacuum, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added. Servicing a double insulated wet/dry vacuum requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated wet/dry vacuum must be identical to the parts they replace. Your double- insulated wet/dry vac is marked with the words ‘double insulated’ and the symbol (square within a square) may also be marked on the appliance.

• To reduce the risk of electric shock-unplug before cleaning or servicing.
• DO NOT use without filters in place.

DO NOT
RETURN TO STORE

Contact Dirt Devil® Support for assistance with your Wet/Dry Vac.

Chat with us!
dirtdevil.com/pages/ddcontact Every day 8am-8pm EST

EXTENSION CORDS

When using an extension cord with your Wet/Dry Vac refer to the following table to determine the required A.W.G. wire size. Before using the vacuum cleaner, make sure the power cord and extension cord are in good working condition. Make repairs or replacements before using the vacuum cleaner. Only use extension cords that are rated for outdoor use.

A.W.G. Wire Size

More than| Not more than
0| 6| 18| 16| 16| 14
6| 10| 18| 16| 14| 12
10| 12| 16| 16| 14| 12
12| 16| 14| 12| Not recommended

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

in death or serious injury.
| WARNING:| Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
| CAUTION:| Indicates a hazardous situation, that, if not avoided, may result in minor or moderate injury.
| NOTICE:| (Without Safety Alert Symbol) Indicates information considered important, but not related to a potential injury (e.g. messages relating to property damage).

PACKAGE CONTENTS

Remove entire contents of carton.
Remove power head from collection tank and remove items inside. Check each item against the carton contents list.

Carton Contents List

NOTE: The hose and accessories for this vacuum are 1.25” (3.2 cm) diameter.

GENERAL ASSEMBLY INSTRUCTIONS

Fully assemble product prior to use.

WARNING: Do not plug in power cord to power outlet. Make sure plug is disconnected before assembling the wet/dry vac.

A Philips head screw driver is required.

UNPACKING YOUR WET/DRY VACUUM & GENERAL ASSEMBLY

1. Verify that the power cord is disconnected from the outlet.

2. Undo the latches.

3. Lift the power head off the collection tank

4. Remove the contents from inside the collection tank; make sure you have all contents as listed. Refer to Package Contents.

5. Turn the collection tank upside down and insert the four caster feet into the slots on the collection tank and tighten with supplied screws.
   Verify that the casters are mounted correctly. Do not over-tighten the screws.

6. Your vacuum comes ready for dry vacuum cleaning with cartridge filter pre-installed. If cartridge filter is not installed. Refer to Filter Installation.

7. For wet vacuum cleaning, install the supplied foam filter.

8. Place the power head back on the collection tank, aligning the top section with the clasps,and snapping into place by applying downward pressure.

9. Insert the locking end of the hose into the port of the collection tank and turn to lock into place.

10. Choose the desired accessories and push onto the vacuum hose.

POLARIZED PLUG To reduce the risk of electrical shock, this appliance has a polarized plug (with one blade wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system.

DRY-VACUUM OPERATION

DRY VACUUMING

WARNING: Be sure to read,understand, and apply information entitled “SAFETY INFORMATION”. Do not vacuum in areas with flammable gases, vapors, or explosive dusts in the air. Flammable gases or vapors include but are not limited to: lighter fluid, solvent type cleaners, oil-based paints,gasoline, alcohol, or aerosol sprays. Explosive dusts include but are not limited to: coal,magnesium, grain, or gun powder. To reduce the risk of health hazards from vapors or dust, do not vacuum toxic materials.

1. Verify that the power cord is disconnected from the outlet.

2. In order to prepare your vacuum for dry vacuuming, verify that the cartridge filter is securely mounted. With power head removed and in upside down position, make sure the filter is pushed in until it stops against the power head and the retainer is installed.

3. Place the power head section back on the collection tank and secure it in place using the latches.
   OPERATING INSTRUCTIONS: DRY VACUUMING

4. Insert the locking end of the hose into the vacuum port on the power head and lock in place. Push the required attach

5. Plug the power cord into the outlet.

6. Turn the motor on by pressing the switch to the ‘I’ ON position.

7. Once you have completed vacuuming, press the switch to the ‘O’ OFF position and unplug the power cord from the outlet.

DO NOT USE THE DUST FILTER FOR LIQUID VACUUMING.

• O = OFF
• I = ON

LIQUID VACUUM OPERATION

LIQUID VACUUM CLEANING

WARNING: Be sure to read,understand, and apply information, entitled “SAFETY INSTRUCTIONS & WARNINGS”. Do not vacuum in areas with flammable gases, vapors,or explosive dusts in the air. Flammable gases or vapors include but are not limited to: lighter fluid, solvent type cleaners, oil-base paints,gasoline, alcohol, or aerosol sprays. Explosive dusts include but are not limited to: coal,magnesium, grain, or gun powder. To reduce the risk of health hazards from vapors or dust, do not vacuum toxic materials.

WARNING: Do not plug in power cord to power outlet. Make sure the plug is disconnected before changing the filters.

1. Verify that the power cord is disconnected from the outlet. Make sure that the collection tank is clean and free from dust and dirt.

2. Remove reusable cartridge filter, then carefully install the foam sleeve filter over the filter cage and place the power head back on the collection tank. See filter installing instructions
   DO NOT USE THE REUSABLE CARTRIDGE FILTER FOR LIQUID VACUUMING.
   OPERATING INSTRUCTIONS – WET VACUUMING

3. Fit the desired nozzle to the vacuum hose.

4. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet.

5. Turn the motor on by pressing the switch to the ‘I’ ON position.)

6. After use, empty the container by unscrewing the drain cap and drain liquids into suitable receptacle or drain. Remember to refit the drain cap to the container after draining container.

IMPORTANT: When vacuuming large quantities of liquids, do not immerse the nozzle completely in the liquid; leave a gap at the tip of the nozzle opening to allow air inflow. The machine is fitted with a float valve that stops the suction action when the collection tank reaches its maximum capacity. You will notice an increase in motor speed. When this happens, turn off the machine, disconnect from the power supply, and drain the liquid into a suitable receptacle or drain. To continue vacuuming, refit the collection tank with the drain cap. After wet vacuuming, turn the machine off and remove the plug from the power supply. Empty the collection tank, clean and dry the inside and outside before storage.

REMEMBER: The foam filter must be removed after wet vacuuming, and a reusable cartridge filter must be installed before dry vacuuming again.

BLOWING OPERATION

This Wet/Dry Vac has blowing capabilities. To use the blower feature, follow the instructions listed.

WARNING: Always wear safety goggles complying with ansi z87.1 (Or, in canada, csaz94.3) Before using blower.

CAUTION: Keep bystanders clear from blowing debris.

WARNING: Wear a dust mask if blowing creates dust that might be inhaled.

1. Verify that the power cord is disconnected from the outlet.
2. Make sure the collection tank is empty before using as a blower.
3. Remove hose from the vacuum port.
4. Insert the locking end of the hose into the blowing port on the back side of the power head and lock into position.
5. Fit the desired extension wand and or nozzle to the vacuum hose.
6. Ensure the power switch is turned off and plug in the power supply.
7. Before turning on the vac, firmly hold the loose end of the hose. Turn the motor on by pressing the switch to the ‘I’ ON position.

CARE AND MAINTENANCE

1. Verify that the power cord is disconnected from the outlet.
2. Disconnect the hose from the vacuum.
3. Undo the latches and remove the power head from the collection tank.
4. Clear all dirt or debris from the collection tank and hose.
5. Check the hose, attachments, and power cord to verify that they have not been damaged.

IMPORTANT: Clean or change the cartridge filter regularly for best performance.

ALWAYS USE DUST FILTER FOR DRY VACUUMING.
If the machine is used without the dust filter, the motor will burn out and the warranty will be voided. Always keep spare dust filters on hand.

NOTICE: The filters included are made of high quality materials designed to stop small dust particles. The dust filter should be used for dry pick-up only. A dry dust filter is necessary to pick up dust. If the dust filter is wet, it will clog quickly and be difficult to clean. Handle the filter carefully when removing it for cleaning or replacing. Check the filters for tears or small holes. A small hole can let dust pass through and out of the cleaner. Do not use a filter with holes or tears in it; replace it immediately.

WARNING: Always disconnect the plug from the power outlet before removing the power head from collection tank.

INSTALLING & CLEANING CARTRIDGE FILTERS

INSTALLING CARTRIDGE FILTER

1. Verify that the power cord is disconnected from the outlet.
2. Remove power head and place in upside down position.
3. Install the cartridge filter over the filter cage with the flat end of the filter towards the vacuum power head. Carefully push the filter in until it stops against the power head.
4. Place filter retainer on top of cartridge filter over the raised lip and tighten down by turning retainer clockwise, taking care not to overtighten.

REMOVING AND CLEANING CARTRIDGE FILTER

1. Unlock and remove the filter retainer by tuning retainer handle counterclockwise.
2. Carefully hold and pull the cartridge filter upward to remove.
3. Clean the cartridge filter by gently tapping or brushing dirt off. Cleaning should not be done indoors in living areas. For optimal performance, a new filter is recommended.
4. Install cleaned or new filter into place as instructed above in steps 2 and 3 of Installing Cartridge Filter.
5. Wet filters should be removed and allowed to air dry for 24 hours before installing onto the filter cage.

INSTALLING & CLEANING FOAM SLEEVE FILTER

Installing Foam Sleeve Filter

1. Verify that the power cord is disconnected from the outlet.
2. Remove power head and place in upside down position. Follow instructions to remove cartridge filter in the section above.
3. Carefully slide foam sleeve filter down over the filter cage making sure the whole cage is covered.
4. Replace the power head onto the collection tank.

CLEANING FOAM SLEEVE FILTER

1. With the removed power head in the upside down position, carefully remove foam sleeve filter.
2. Use a mild soap and water solution to wash foam sleeve filter and rinse with clean water.
3. Allow filter to air dry before installing and using again.

SERVICE PARTS

TROUBLESHOOTING

WARNING: To reduce the risk of electric shock, unplug before troubleshooting.

breakers, fuses.
2. Faulty power cord.| 2. Unplug and check the power cord. If damaged, have it repaired by a professional.
3. Collection tank full.| 3. Empty collection tank.
The dust comes out from the motor cover.| 1. The dust filter is missing or damaged.| 1. Attach or replace dust filter.

Reduced efficiency and motor/speed vibration.

| 1. There is a blockage in the nozzle or hose, or the col- lection tank inlet. Or dust filter blocked by fine dust.| 1. Check nozzle, hose and collection tank inlets for blockage. Take off the filter and clean it. Or install new dust filter.

WARRANTY

LIMITED WARRANTY FOR DIRT DEVIL® PRODUCT / 2 (TWO) YEARS LIMITED WARRANTY (DOMESTIC USE)

If this product is not as warranted, contact TTI Floor Care North America Customer Service at 1-800-321-1134. Please have available the proof of purchase and model number for the warranted product.
Failure to register the product does not diminish product warranty rights.

WHAT THIS WARRANTY COVERS: This limited warranty provided by Royal Appliance Mfg.
Co., doing business as TTI Floor Care North America (referred to hereafter as “Warrantor”) applies only to products purchased in the U.S. (including its territories and possessions), a U.S. Military Exchange, or Canada. When used and maintained in normal household use and in accordance with the Owner’s Guide, this product is warranted against original defects in material and workmanship for 2 (Two) years from the date of original purchase (the “Warranty Period”). If Warrantor determines that the issue you are experiencing is covered under the terms of this warranty (a “covered warranty claim”), we will, at our sole discretion and free of charge (subject to the cost of shipping), either (i) repair your product; (ii) ship you a replacement product, subject to availability; or (iii) in the event that the applicable parts or replacement are not reasonably available, ship you a similar product of equal or greater value. In the unlikely event that we are unable to repair your product or ship a replacement or similar product, we reserve the right, at our sole discretion, to issue you a refund or store credit (if applicable) of the actual purchase price at the time of the original purchase as reflected on the original sales receipt. Parts and replacements may be new, refurbished, lightly used, or remanufactured, in Warrantor’s sole discretion.

WHO THIS LIMITED WARRANTY COVERS: This limited warranty extends only to the original retail purchaser, with original proof of purchase from Warrantor or an authorized dealer of Warrantor products, in the U.S., U.S. Military Exchanges, and Canada.

WHAT THIS WARRANTY DOES NOT COVER: This warranty does not cover use of the product in a commercial operation (such as maid, janitorial, and equipment rental services, or any other income-generating activity); improper maintenance of the product; the product if it has been subject to misuse, negligence, neglect, vandalism, or the use of voltages other than that on the data plate of this product. This warranty does not cover damage resulting from an act of God, accident, owner’s acts or omissions, service of this product by other than Warrantor or a Warrantor authorized service provider (if applicable), or other acts beyond the control of Warrantor. This warranty also does not cover use outside the country in which the product was initially purchased, or resale of the product by the original owner. Pick-up, delivery, transportation, and house calls are not covered by this warranty. In addition, this warranty does not cover any product that has been altered or modified, or repairs made necessary by normal wear or the use of other products, parts, or accessories which are either incompatible with this product or adversely affect this product’s operation, performance, or durability. Normal wear items are not covered under this warranty. Depending on the product, normal wear items may include, but are not limited to, belts, filters, brush rolls, blower fans, blower and vacuum tubes, and vacuum bags and straps.

OTHER IMPORTANT TERMS: This warranty is not transferable and may not be assigned; any assignment made in contravention of this prohibition is void. This warranty shall be governed and construed under the laws of the state of North Carolina. The Warranty Period will not be extended by any replacement of batteries, parts, or products or by virtue of any repair performed under this warranty.

THIS LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY AND REMEDY, AND ALL EXPRESS AND IMPLIED WARRANTIES OTHER THAN THE LIMITED WARRANTY SET FORTH ABOVE, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED. IN NO EVENT WILL WARRANTOR BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE TO OWNER OR ANY PARTY CLAIMING THROUGH OWNER, WHETHER BASED IN CONTRACT, NEGLIGENCE, TORT, OR STRICT PRODUCTS LIABILITY OR ARISING FROM ANY CAUSE WHATSOEVER, EVEN IF THIS WARRANTY FAILS OF ITS ESSENTIAL PURPOSE. TO THE EXTENT PERMITTED BY APPLICABLE LAW, NO WARRANTIES THAT ARISE BY OPERATION OF LAW, IF APPLICABLE, SHALL EXCEED THE DURATION OF THE LIMITED WARRANTY PROVIDED HEREIN. Warrantor’s liability for damages to you for any costs whatsoever arising out of this statement of limited warranty shall be limited to the amount paid for this product at the time of original purchase.

Some states do not allow the exclusion or limitation of incidental or consequential damages, disclaimers of implied warranties, or limitations on the duration of implied warranties, so the above exclusions, disclaimers, and/or limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

GENUINE PARTS AND ACCESSORIES: We recommend using only with genuine Dirt Devil® parts, and accessories. Damage caused by use with other than genuine Dirt Devil® parts, and accessories is not covered by and may void your warranty.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>