nutrichef NCHUB13 Series Digital Hot Water Dispenser User Guide
- August 22, 2024
- nutrichef
Table of Contents
USER GUIDE
Digital Hot Water Dispenser
Instant Water Boiler/Water Heater,
Auto Dispense Safety Lock
**NCHUB13 – NCHUB24 – NCHUB35
**
Safety Precautions
When using an electrical appliance, basic safety precautions should always be followed, including the following:
-
It is essential to read the Instruction Manual carefully before use.
-
Please carry or handle this Hot Water Dispenser using the built-in carrying handle.
-
Do not place it on or near other high-temperature appliances.
-
Do not immerse the power cord or Hot Water Dispenser body in water or other liquids to avoid electric shock.
-
Keep this Hot Water Dispenser out of children’s reach during use.
-
Make sure to unplug the power cord from the Water Dispenser when cleaning it.
-
Do not use the Hot Water Dispenser if the power cord is frayed, damaged, or if it operates abnormally. Send it to the nearest authorized repair facility for inspection, adjustment, or repair. Do not attempt to disassemble or repair it.
-
Itis not recommended to use tools other than those included with this Hot Water Dispenser.
-
This Hot Water Dispenser is for indoor use only.
-
Do not suspend the power cord off the edge of tables or countertops to avoid injury resulting from overturning the Hot Water Dispenser.
-
Keep this Hot Water Dispenser away from hot surfaces, stoves, and baking ovens.
-
This Hot Water Dispenser operates using only 120V AC.
-
Ensure that the exterior/interior of the Hot Water Dispenser is clean and free of foreign material.
-
Do not place hands close or touch the steam vent to prevent burns resulting from high-temperature steam released during boiling water.
-
Do not boil more water than the maximum allowable amount.
-
Use a damp cloth or sponge for cleaning the Hot Water Dispenser.
Never use metal or abrasive scrubbers. -
Do not use this Hot Water Dispenser for purposes other than its intended use.
-
Always use caution when there is hot water present in the Hot Water Dispenser.
-
Do not suddenly change the temperature of the inner metal lining, for example, by adding ice into boiling water.
-
Do not touch the bottom heating area until it cools down.
Please keep this Instruction Manual for future reference.
Introduction
The Nutrichef Digital Hot Water Dispenser is tailored for making hot water available 24/7. With the new emphasis on “Healthy Living-Healthy Life,” many people are adding hot tea to quench their thirst. Today, as people are exposed to more chemicals and heavy metals in their environment, they are developing certain sensitivities to them. From these sensitivities, awareness and fears of using non-stick coated cookware are ever-increasing. Taking this into consideration, along with the pursuit of healthier living, our company has developed and manufactured the Nutrichef Digital Hot Water Dispenser. We believe our Hot Water Dispenser, free of chemicals and heavy metals, promotes a healthier, stress-free living.
Functions
The Nutrichef Digital Hot Water Dispenser is tailored for people who lead a
busy, active lifestyle and are also health-conscious. This Hot Water Dispenser
can boil water and keep it warm at three different temperatures.
Keep warm at 208°F; suitable for tea, instant coffee, and other instant
drinks, at 185°F; an energy-saving default keep warm temperature setting, and
149°F; ideal for Japanese Green Tea or Baby Formula.
It also comes with a Stand-by function for extended energy savings when you
will not use the Hot Water Dispenser for a long period, such as when you are
asleep.
Specifications
| Model | Voltage | Frequency | Power | Capability |
|---|---|---|---|---|
| NCHUB13 | 120V | 60 Hz | 750W | 3.0 Liter |
| NCHUB24 | 120V | 60 Hz | 750W | 4.0 Liter |
| NCHUB35 | 120V | 60 Hz | 750W | 5.0 Liter |
Main Parts Diagram
Control Panel
Directions
Pay attention to the following before use:
-
Preparation prior to first operation.
Take out the Digital Hot Water Dispenser, Power cord, Instruction manual, and warranty from the packing box.
• Fill out the warranty card and mail it back to our Company for registration and one-year after-sales service. Your rights and benefits will only be guaranteed if we receive your completed warranty.
• Set aside packing materials and the box for future storage and transport.
• Please read the Instruction Manual carefully for the proper use of this kettle.
• Do not plug the power cord into the outlet before being ready to use.
• Ensure the interior and exterior of the kettle are dry and clean before pouring water into it (Filtered Water is recommended for boiling in this kettle). -
Press the “TEMP SET” Button to select your desired keep warm temperature.
-
The Digital Hot Water Dispenser is designed to boil water and keep it warm 24/7 for your convenience. Do not use this kettle for anything other than heating water.
-
The Digital Hot Water Dispenser is characterized by its ease of operation and convenience. Enjoy!
How to use
-
Open Lid to Pour Water
NOTE : Filtered Water is recommended for boiling in this Hot Water Dispenser. • Do not spill water outside of this kettle.
• Close the lid after pouring water.
• Please do not over fill water pass the Max Water Level. It might cause overflow during boiling -
Plug in the Power Cord to start boiling 1. Connect the Power Cord to the Hot Water Dispenser. 2. Plug the Power Cord into the power outlet.
After connecting to the outlet, the “BOILING” indicator lights up, and water starts to boil automatically until reaching a boiling temperature of (212°F). -
When the water is boiling, the Hot Water Dispenser will switch to keep-warm
mode. The Default (or customer-selected) Temp indicator of 185°F lights up. + The Hot Water Dispenser will re-boil again if the water temperature drops below the set temperature level
« If the Hot Water Dispenser does not boil automatically, press the “RE-BOIL” button to boil water.
4. Each time the “TEMP SET” button is pressed, the keep-warm temperature indicator will switch in the following sequence: 185°F -> 208°F -> 149°F -> 185°F -> -
TWO WAYS TO DISPENSE HOT WATER
1. Press the “UNLOCK” button; the unlock light is on.
(Hot Water Dispenser will auto-lock if idle for 10 seconds.) 2. Push Button Dispensing: Press the “‘DISPENSE” button to dispense hot water into the cup.
Cup Touch Dispensing: Hold the cup up to touch the cup switch behind the spout to dispense hot water into the cup. NOTE:
After water has boiled without dispensing for a period, some air might become trapped in the water pump, preventing water pumping. Simply open, then close the lid to solve this issue. -
STAND-BY FUNCTION
1. During water boiling, press the “RE-BOIL” button once; the kettle will turn into STANDBY mode and stop boiling. To resume boiling, press “RE-BOIL” again 2. If the Dispenser is in keep-warm mode, press the “RE-BOIL” button twice to set the Hot Water Dispenser into STANDBY mode. Resume boiling by pressing ‘RE-BOIL” again
Maintenance
BODY
Wipe the Hot Water Dispenser body with soft dry cloth.
-
Wipe the Hot Water Dispenser body with a soft, dry cloth.
-
Wipe with a damp cloth if the stain is hard to remove.
(Never use a soaked cloth!) -
Don’t use thinner to clean; it might crack the plastic casing.
-
Any cloth containing chemicals might cause color changing of the body.
WARNING : This Hot Water Dispenser is not Dishwasher safe!
REMOVE SCALE DEPOSIT
If using tap water, the minerals in the water will deposit on the surface of
the stainless steel lining over time. This deposited scale will shorten the
life of this Hot Water Dispenser. Please clean this Hot Water Dispenser with
citric acid at least once a month. Follow the instructions on the citric
acid’s package to clean and remove mineral deposits.
LINING
Wipe the lining with a damp sponge.
Don’t use detergent or any kind of abrasive brush.
REPLACE SILICON SEAL
The silicon seal may become damaged after a long period of use.
It should be replaced. Call our service line or order on our web store for a
replacement silicon ring
It is easy to replace the silicon ring by following these steps: Remove the
four screws inside the bottom of the upper lid. Remove the stainless steel
plate.
Take out the existing silicon ring and replace it with the new ring. Put back
the stainless steel plate. Tighten the four stainless steel screws.
STORAGE
- Pull the plug out of outlet.
- Pull the cord out of kettle.
- Remove upper lid
- Pour all water out of kettle
Troubleshooting
| TROUBLES | POSSIBLE CAUSE | SOLUTION |
|---|
White mineral or shiny specks floating in the water or deposited on the
surface of the inner lining of the Hot water Dispenser| Mineral Crystalized in
water| Clean with citric acid.
How to clean?
See REMOVE SCALE DEPOSIT
section in this menu or the instruction on the package of citric acid
Tap water contain too much minerals causing deposits on the surface of the
inner lining
Odors in the hot water| Chlorine in the tap water may cause odor| Press “RE-
BOILER” to De-Chlorine
For the first few uses, it may have a plastic smell in the water because of
new plastic
components.| Boil a new pot of water for few times before normal use
Water does not pump out smoothly| Filter might be plugged| Clean the filter
with citric acid
Air might be trapped in the water pump| Open the upper lid and closed
it few times, then try again.
Does not pump water out at all| Check that the unlock indicator is off| Press
“UNLOCK” button once then press “DISPENSE” to see whether it works or not
Hot water leaking out from the nozzle| Too much water in the pot| Make sure
the water is not filled above the MAX water level line.
No Power| Check the power cord| Attach power cord firmly to both outlet and
Hot Water Dispenser
Hot Water Dispenser body case feels hot| To keep water hot when at higher room
temperature the body case might reach 149°F
OVERHEAT PROTECTION
When the Hot Water Dispenser is empty of water, an overheat safety protection
sensor will automatically activate, swiftly turning off the power to prevent
overheating. Simultaneously, the temperature keep warm lights will blink when
the overheat protection is triggered.
This Hot Water Dispenser comes with overheat protection sensors.
However, operating the dispenser without water while it’s powered on is
extremely dangerous and can lead to fire and property damage.
Always maintain water above the REFILL line on the water gauge to prevent
accidents.
Note:
If issues persist after following troubleshooting steps, contact our service
center or an authorized repair center for assistance.
Do not attempt to disassemble the Hot Water Dispenser yourself, as it will
void the manufacturer’s warranty.
The following cases are exempted from free maintenance or warranty:
- Failure to present the invoice, pre-pay postage, or submit the warranty registration form to our company.
- Damage to the Hot Water Dispenser due to inappropriate use.
- Use for commercial purposes.
- Damage to the Hot Water Dispenser resulting from unexpected accidents after purchase.
- Damage to the Hot Water Dispenser due to self-modification or repair.
- Damage to the Hot Water Dispenser resulting from natural and/or manmade disasters.
Hot Water Dispenser Features:
- 360° Rotating Base
- Instantly Heat & Dispense Hot Water!
- Simple Electric Plug-in Design
- Built-in LED Light Illuminates When Dispensing
- Adjustable Water Temperature & Dispensing Amounts
- Convenient Easy Access Refillable Water Tank
- Transparent Water Container with Clear Level Mark
- Safe for Placement on Any Table or Countertop
- Used for All Drinks Including Instant Coffee, Tea & Soups!
- 2 Way Easy Dispensing Methods: Electric Auto Dispense & Cup Touching
- Automatically Keep Warm and Reboil
- Dry-boiled Protection and Safety Auto Shut-off
What’s in the Box:
- Heating Unit
- Cable
NCHUB13
3L Digital Hot Water Dispenser
Technical Specs:
- Heating Element: 750Watt
- Capacity: 3L
- Electric Auto Dispense Amounts: 100z – 160z per 10 seconds
- Temp. Adjustment: 149 / 185 / 208° Fahrenheit
- Construction Material: 304 Stainless Steel Inner Pot and #430 Stainless Steel Outer Housing
- Power Cord Length: 4.593′ ft.
- Power Supply: 120V, 60Hz
- Product Dimensions (L x W H): 11.81″ x 7.87″ x 9.84″ ~inches
NCHUB24
4L Digital Hot Water Dispenser
Technical Specs:
- Heating Element: 750Watt
- Capacity: 4L
- Electric Auto Dispense Amounts: 100z – 160z per 10 seconds
- Temp. Adjustment: 149 / 185 / 208° Fahrenheit
- Construction Material: 304 Stainless Steel Inner Pot and #430 Stainless Steel Outer Housing
- Power Cord Length: 4.593′ ft.-
- Power Supply: 120V, 60Hz
- Product Dimensions (L x W H): 11.81″ x 7.87″ x 11.81″ —inches
NCHUB35
5L Digital Hot Water Dispenser
Technical Specs:
- Heating Element: 750Watt
- Capacity: 5L
- Electric Auto Dispense Amounts: 100z – 160z per 10 seconds
- Temp. Adjustment: 149 / 185/ 208° Fahrenheit
- Construction Material: 304 Stainless Steel Inner Pot and #430 Stainless Steel Outer Housing
- Power Cord Length: 4.593′ ft.
- Power Supply: 120V, 60Hz
- Product Dimensions (L x W H): 11.81” x 7.87″ x 13.78″ —inches
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>