TRADER SCOYSTER Scorpion Oyster Light Instruction Manual
- August 21, 2024
- TRADER
Table of Contents
TRADER SCOYSTER Scorpion Oyster Light
Product Usage Instructions
- Isolate Power Supply: Turn off the mains power supply before starting installation.
- Select Installation Position: Choose the desired location for installation.
- Mounting Bracket: Attach the central mount bracket to the ceiling, align, and mark screw positions.
- Drill and Insert Fixtures: Drill holes for mounting screws and cable passage.
- Fasten Bracket: Securely attach the bracket to the ceiling and connect cables to terminals.
- Connect Lamp Wires: Terminate Active and Neutral wires correctly.
- Select CCT Color: Set the desired color temperature on the selector switch.
- Attach Lamp Body: Align the lamp body with the bracket, push upwards, and rotate to lock it in place.
- Restore Power: Reconnect the power supply, switch on, and test for proper operation.
FAQs
- Q: Is this product suitable for outdoor use?
- A: No, this product has an IP20 rating which means it is only suitable for indoor use.
- Q: Can the color temperature be changed after installation?
- A: Yes, the color temperature can be changed by adjusting the selector switch on the product.
- Q: Is this product dimmable?
- A: No, this product is not dimmable.
Product Specification
Part Code | SCOYSTER |
---|---|
Colour Temp | 3000K |
4000K
5700K
Lumen Output| 3600lm
IP Rating| IP20
Power| 30W
Beam Angle| 100°
CRI| >80
Voltage Rating| 220-240V~ 50Hz
LED Lamp Life (L70)| 30,000 Hrs
Dimmable| No
Operating Temp| -10°C to 40°C
Electrical Class| Class II
These luminaires comply with AS/NZS 69598.2.1 for surface mounting to ceilings.
Installation Method
Read the instructions and check you have all the tools and accessories to complete the installation correctly.
- Isolate the main power supply before starting the installation.
- Select a position for installation.
- Remove the central mount bracket, align it on the ceiling, and mark the appropriate positions for the mounting screws (See Fig 1).
- Drill and insert ceiling plugs, and a central hole for the cable and pull through ready for termination. (See Fig 2).
- Fasten the mounting bracket to the ceiling as per the diagram, then after removing the terminal cover by loosening the 4 screws to expose the terminals. Terminate the cables for Active to the L terminal and Neutral to the N terminal. Make sure the outer insulation from the cable for both fixed wiring and from the light is captured under the terminal cover and tighten down the 4 screws as shown (See Fig 3).
- Connect wire trace strain relief to help support the lamp to the bracket. (See Fig 4)
- Connect lamp wires to the terminals and ensure secured.
- Make sure the selected CCT color (See Fig 3) is set on the selector switch (See sticker marked on product)
- Align lamp body onto the bracket and push up against ceiling (See Fig 4, 5 and 6) and rotate to lock in place.
- Restore the power supply, switch it on, and test for correct operation.
Important Information
- It is recommended that luminaires be installed and fitted by a qualified electrician, ensuring the installation complies with the current building regulations.
- These products are designed for connection to a 220-240V~50Hz supply.
- The trader will not accept responsibility for any claims arising from incorrect installation or application.
- If cleaning is necessary, ensure the product is switched off and only wipe the accessible lens and housing with a damp cloth and dry off using a dry lint-free cloth.
Warning
- Caution no user serviceable parts contained, risk of electric shock if dismantled.
- Cutting cables or damaging components will void the warranty.
- Check whether the product has been damaged in transport.
- Do not operate or install any product that appears damaged in any way.
- Return the complete product to the place of purchase for inspection or replacement.
Warranty
- This product has been manufactured to the highest quality standards.
- This product is warranted to the original purchaser and is not transferable.
- The product is guaranteed to be free from defects in workmanship and parts for 5 Years from the date of purchase, for full warranty details please refer to www.gsme.com.au.
Installation Instructions
SCOYSTER // Oyster Light, 30W LED 3600lm, 420mm diameter x 28mm depth, CCT3 3000K/4000K/5700K, IP20
Remove terminal cover. Connect neutral to terminal marked ‘N’ and ‘Active’ to ‘L’ terminal. Replace terminal cover. Ensure outer cable insulation is covered.
CONTACT INFORMATION
- GSM Electrical (Australia) Pty Ltd, Level 2 142-144
- Fullarton Road, Rose Park SA 5067
- www.gsme.com.au.
- Phone: 1300 301 838
- Fax: 1300 301 778
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>