TRADER MEPBE Push Button Electronic On/Off Switch Instruction Manual

August 20, 2024
TRADER

Installer’s Manual
3-WIRE

SUITABLE FOR
FANS, MOTORS
OR IRON CORE
BALLASTS

MEPBE Push Button Electronic On/Off Switch

MEPBE Push Button,Electronic On/Off Switch, 3-wire
Scan QR code with your phone to see technical information on our website

http://gsme.com.au/spec/MEPBE

FEATURES

  •  Soft touch push button ON/ OFF switch.
  • Blue LED indicates device status.
  • Returns to OFF after loss of power.
  • Compatible with a wide range of load types including wire wound transformers & fan motors.
  • Compatible with Trader and Clipsal* Style wall plates.
  • Multi-Way Switching compatible with the MEPBMW Push Button, Multi-Way Remote and On/Off.

OPERATING CONDITIONS

  • Operating Voltage: 230V a.c. 50Hz
  • Operating Temperature: 0 to +50 °C
  • Compliance Standard: CISPR15, AS/NZS 60669.2.1
  • Maximum Load: 1200W / 500VA
  • Maximum Current Capacity: 5A
  • Terminals: Screw Terminals suit 0.5mm 2 to 1.5mm2 stranded cable (bootlace terminal recommended)

Note: Operation at temperature, voltage or load outside of the specifications may cause permanent damage to the unit.

LOAD COMPATIBILITY

LOAD TYPE COMPATIBILITY
Incandescent / 240V Halogen 1200W
Fluorescent Tube with Electronic Ballast 500VA
Fluorescent Tube with Iron Core Ballast 500VA
Compact Fluorescent 500VA
Electronic Transformer 500VA
LED 500VA
Wirewound Transformer 500VA
Fan Motors 500VA
Heating Elements 1200W

WIRING INSTRUCTIONS

WARNING: The MEBPE is to be installed as part of a fixed wire electrical installation. By law such installations must be made by an electrical contractor or similarly qualified person.
NOTE: A readily available disconnect device, such as a type C 16A circuit breaker shall be incorporated – external to the product. 4.1 REMOTE SWITCH

  • The MEPBE is Multi-Way switching compatible with the MEPBMW Push Button. Alternatively, a mains rated momentary action switch can be used to wire across the Active and Remote connections.
  • Total length of remote wiring should not exceed 50 metres.
  • Holding a remote button longer than 2 seconds will turn the power OFF.

IMPORTANT SAFETY WARNINGS

5.1 LOAD REPLACEMENT

  • It should be assumed that even when OFF, mains voltage will still be present at the load fitting. Mains power should therefore be disconnected at the circuit breaker before replacing faulty loads.

5.2 INSTALLATION

  • The MEPBE is to be installed as part of a fixed wire electrical installation. By law, such installations must be made by an electrical contractor or similarly qualified person. Avoid excessive force on remote input wire or terminal block during installation.

5.3 LOW READING DURING INSULATION BREAKDOWN TEST

  • The MEPBE is a solid-state device and therefore a low reading may be observed when conducting insulation breakdown testing on the circuit.

5.4 CLEANING

  • Clean only with a damp cloth. Do not use abrasives or chemicals.

TROUBLESHOOTING

6.1 LOAD FAILS TO TURN ON WHEN THE BUTTON IS PRESSED

  • Ensure that the circuit has power by checking the circuit breaker.
  • Ensure the load is not damaged or broken.

6.2 LOAD FAILS TO TURN OFF WHEN THE BUTTON IS PRESSED

  • If the LED is OFF and if applicable, check that the remote push button is not stuck ON. If not, the MEPBE may be damaged and should be replaced.

WARRANTY AND DISCLAIMER

Trader, GSM Electrical (Australia) Pty Ltd warrants the product against manufacturing and material defect from the date of invoice to the initial purchaser for a period of 12 months. During the warranty period Trader, GSM Electrical (Australia) Pty Ltd will replace products that prove to be defective where the product has been correctly installed and  maintained and operated within the specifications defined in the product data sheet and where the product is not subject to mechanical damage or chemical attack. The warranty is also conditional on the unit being installed by a licensed electrical contractor. No other warranty is expressed or implied. Trader, GSM Electrical (Australia) Pty Ltd shall not be liable for any direct, indirect, incidental or consequential damages.
*The Clipsal brand and associated products are Trademarks of Schneider Electric (Australia) Pty Ltd. and used for reference only .

GSM Electrical (Australia) Pty Ltd //
Level 2, 142-144 Fullarton Road, Rose Park SA 5067 //
P: 1300 301 838 F: 1300 301 778
E:service@gsme.com.au
3302-200-10890 R3 //
MEPBE Push Button, Electronic On/Off
Switch, 3-wire – Installer’s Manual 200501 1

Documents / Resources

| TRADER MEPBE Push Button Electronic On/Off Switch [pdf] Instruction Manual
MEPBE, MEPBMW, MEPBE Push Button Electronic On Off Switch, MEPBE, Push Button Electronic On Off Switch, Electronic On Off Switch, On Off Switch, Off Switch, Switch
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals