Rebel RBA-4507 Rowing Machine User Manual

Rebel RBA-4507 Rowing Machine

Product Information

The Active SUP Board is a versatile stand-up paddleboard suitable for both beginners and experienced users. It can be inflated for use on the water and deflated for easy storage and transportation. The board features a valve for inflation and deflation, as well as a fin that can be installed both when the board is inflated or deflated.

Specifications:

• Model: RBA-4507
• Product: Active SUP Board

Product Usage Instructions

Safety Information:
Before using the Active SUP Board, ensure you read and understand all safety instructions provided in the user manual.

Unfolding the Board:
To access the valve, unscrew the security screw counterclockwise. To open or close the valve, move the spring-loaded needle. To close the valve, set the needle in an upward position, press the needle, and rotate it clockwise until it locks in place.

Inflating:

1. Connect the pump nozzle to the board valve and rotate it clockwise.
2. Start pumping air into the board until it reaches the desired inflation level.
3. After inflating, disconnect the pump nozzle and close the valve securely.

Storage:

1. Deflate the board by releasing the air and remove the fin.
2. Clean and inspect every segment and accessory of the board.
3. Store the board in a dry, cool place to prevent damage.

FAQ:

• Q: Can I use the fin when the board is deflated?
  A: Yes, the fin can be installed on the Active SUP Board whether it is inflated or deflated.

• Q: How should I store the board when not in use?
  A: When not in use, deflate the board, remove the fin, clean all components, and store it in a dry place away from direct sunlight.

SAFETY INFORMATION

• Read this instruction manual carefully before inflating the board.
• This manual is not a board swimming course. If it is your first board, or you changed the board to different kind, make sure to familiarize yourself with the board. Make sure that the wind and conditions on the water are suitable for the board and that the board can be steered.
• The board should be used in the intended way. Pay attention for any damage caused by wear or inappropriate use.
• Every board, no matter the endurance, can become damaged if it is used inappropriately. Always adjust speed and direction of the board accordingly to the conditions on the water. Everyone using the board must be wearing appropriate equipment (life jacket or other equipment that floats).
• The board has a bulge near the valve. This is normal and every board has this.
• Do not exceed the weight limitations of the board.
• Do not inflate the board with an air compressor.
• Before using the board, make sure to inflate all of the sections.
• Do not use the board during bad weather and when the conditions on the water can affect the ability to come back to shore safely.
• Always have contact with the board, always wear safety harness that is connected with the board. Wind and water current can carry the board faster.
• Do not dive directly from the board.
• The board is not designed to be towed by a boat.
• Do not allow children to use the board without adult supervision.
• Do not drink alcohol while using the board.
• Do not use the board after dark or with bad lighting.
• Do not expose the board to direct sunlight after taking it out of water.
• Keep the board away from sharp objects.
• The product is intended for people who can swim.

USAGE

UNFOLDING THE BOARD
Unfold the board on flat and clean surface. First inflating should be conducted inside, in room temperature. This way the PCV material will be more flexible, and the process easier. If the product has been stored in a temperature below 0°C, leave it in 20°C for 12 hours before unfolding.

VALVE
To access the valve, unscrew the security screw counterclockwise. To open or close the valve, move the spring-loaded needle. To close the valve, set the needle in upward position- press the needle and rotate it clockwise, until the needle locks in the upward position.

INFLATING

1. Connect the pump nozzle to the board valve, rotate it clockwise and start pumping.
2. After inflating the board disconnect the nozzle and close the security screw.

Caution: after leaving the board on sunlight, check the board air pressure.

DEFLATING
Clean the board from water and the valve from debris. Unscrew the security screw. Press the valve needle and slowly deflate the board. After 10 seconds push the valve needle all the way down until it locks down in open position. During deflating prevent the sand and other debris from getting into the valve.
Caution: the board valve is not tightened all the way down in the production process. To avoid the air loss, tighten the valve using the valve key. Unscrew the security screw, insert the key and rotate it to “CLOSE” position. During this process hold the valve and make sure not to over tighten it.

FIN INSTALLATION

The fin can be installed when the board is inflated, as well as deflated.

STORAGE

1. Deflate the board and take out the fin.
2. Clean and check every segment and accessory (including the paddle) after each use. If the product was used in a saltwater, make sure to remove all the water from the board. To clean the board use mild soap, do not use any detergents or silicone-based products. Make sure to dry the board before storage.
3. Keep the valve open when folding the board. Close it while using the board.
4. Store the board in dry and clean place, where the temperature is constant. Store the board deflated and folded in the bag, or folded and slightly inflated. Do not expose the product to deformation.
5. Store the paddle disassembled.

FIXING LEAKS

Included in set are PVC patches for fixing small leaks.

1. Make sure that there are no sand or debris in the valve.
2. Make sure that the valve gasket is in place.
3. Clean the board with soap and water, including the valve.
4. Clean thoroughly the leak spot.
5. Cut the piece of patch in a way, that it covers 1,5 cm from the leak spot.
6. Put a thin layer of glue onto patch and leak spot. Wait 2-4 minutes until the glue sets.
7. Put the patch on the leak spot and apply pressure. Do not use the board for the next 24 hours until the glue dries.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>