strands NUUK E-Line Duo License Plate LED Bar Instruction Manual

strands NUUK E-Line Duo License Plate LED Bar

Product Specifications

• Product Name: NUUK E-LINE DUO LICENSE PLATE LED BAR
• Power Source: Battery
• Operating Voltage: 12V
• Fuse: 20A
• Connector Type: 3PIN-DT Connector
• Number of LEDs: Not specified
• Part Number: 809138
• Manufacturer Websites: www.strands.se, www.strandseurope.com

Product Usage Instructions

Installation:

1. Identify the installation surface on your car for mounting the license plate LED bar.
2. Use the provided wiring harness to connect the LED bar to the battery.
3. Secure the LED bar using the adjustable screws with springs and mounting screws.
4. Attach the number plate buckle and spacers to ensure proper alignment.

Wiring:

The wiring configuration is as follows:

• BLACK wire to negative (-) terminal
• RED wire to positive (+) terminal
• WHITE wire for switching signal line

Maintenance:

Regularly check the connections and ensure all screws are tight to prevent any loose fittings.

Usage:

The license plate LED bar is designed to provide illumination for your license plate, enhancing visibility and style.

Frequently Asked Questions

• Q: How do I know if the LED bar is properly connected?
  • A : Check that the black wire is connected to the negative (-) \terminal of the battery and the red wire is connected to the positive (+) terminal. Ensure the white wire is correctly connected for the switching signal.
• Q: Can I use this LED bar on any car model?
  • A: The LED bar can be installed on most car models, but it is recommended to verify compatibility with your vehicle before installation.

WIRING INSTRUCTIONS

• (PIN A) RED = +VDC
• (PIN B) BLACK = – TO CHASSIS GROUND
• (PIN C) WHITE = SIGNAL WIRE TO SWITCH

Note:This wiring harness does not require additional relays. To turn on the light, connect the signal wire of the switch (WHITE WIRE) to the positive ‘+'(HIGHBEAM)

Installation

Steps for license plate holder installation:

1. Take off the cardboard from the license plate.
2. Lock the adjustable screw with spring (x 4pcs) into the screw hole positions on the back of the license plate holder, and adjust the screw depth according to the installation position. Please ensure that the mounting bracket is securely attached in a manner that ensures it is parallel to the road surface and check LED light fixture is perfectly straight with the direction of the vehicle. This alignment will enhance optimal illumination.Make sure the positioning before moving to step 3.
3. Position the license plate securely, Place silicone spacers with the appropriate height between the installation surface and the license plate holder, and then lock it in place using the mounting screws.
4. Insert the license plate into the license plate holder, and then firmly press the number plate buckle into place within the holder
5. When working with electrical wiring and cabling, it is important to take all necessary safety precautions. Make sure that all electrical connections and cable handling are done in a secure way to avoid the risk of fire or electric shock.

Contact us if you need support: support@strands.se or +46(0)320-450450

• www.strands.se
• www.strandseurope.com

READ THIS BEFORE INSTALLATION OR PAINTING

READ ALL INSTRUCTIONS AND STUDY DIAGRAMS BEFORE PAINTING OR INSTALLING YOUR NEW LIGHTS!

LEGAL MOUNTING

Check with state or local authorities for laws governing usage and proper mounting of your new lights.

TAKE CARE OF YOUR PRODUCT

Keep the product clean. Dirt on the lens and heat sink may shorten the product’s lifetime. We recommend using lukewarm water and alkaline degreasing. Follow the degreasing instructions carefully and rinse off gently with cold or lukewarm water on low pressure.

WARNING!

Strong chemicals should not be used on the product. If you accidently get strong chemicals on the product, rinse off immediately, use plenty of water so that no chemicals remain in any joint. Some chemicals have a small amount of solvent in them, this can dissolve sealing adhesives and compromise the product’s waterproofness. Some chemicals pull out liquid from plastic and rubber-based components, which makes the plastic or rubber brittle and bursts more easily. Be careful not to use high water pressure close up on the product. If you use high water pressure at short distances, most products find it difficult to close out the water.

INSTALLATION

If there is a contact/connector on the product, it should not be cut. If the connector is cut, the warranty is not valid. If the product has loose cable and no connector. If the cable is shorter than 50 cm, the cable must not be cutted. If the cable is cut, the warranty is not valid. If the cable is longer than 50 cm, it is ok to shorten the cable, but not shorter than 50 cm. If the cable is cut shorter than 50 cm, the warranty is not valid. Tighten screws and bolts so that they do not loosen or chafe. Do not tighten screws so hard that the protective bearings on the product break.

WARNING!

Do not use higher volts than the product description states. This light becomes hot under continuous use. Don’t remove or touch the casing for at least 30 minutes after turning the lamp off.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>