Clarke JSM1000 Jampstarter Instruction Manual

Clarke JSM1000 Jampstarter

Product Information:

Specifications

• Item Weight: 365 g
• Size (L x W x H): 146mm x 78mm x 31mm
• Max Output Current (12V): Starting 500A Peak 1000A
• Output Voltage (open circuit): 14.8V
• Input Voltage/Current: 5 V / 2A
• Battery Type: Sealed re-chargeable lithium-polymer
• USB(A) Output Power Supply: 5 V DC – (2.1A & 3.0A)
• Estimated Engine Starting Capacity: Up to 2.5 litres (diesel) or 5 litres (petrol)
• Full Charging Time: Approx 6 -7 hours from flat
• Lifetime Duration Before Recharging: 1000 cycles
• Number of Starts Before Re-charging: 20 max
• Protection Features: Short circuit, over-charge protection, and discharge protection
• USB Cable Plugs: 1 x USB C, 1 x Micro USB
• Work Light: 1 x Lighting LED, 3V, 1W
• Ingress Protection: IP20

Product Usage Instructions

General Safety Guidelines

1. Avoid exposure to elements such as direct sunlight, heat, rain, and moisture.
2. Use the device indoors or in a protected area.
3. Do not operate if cables are damaged; consult a dealer for repair.
4. If the case is damaged, seek inspection and repair from a qualified person.
5. Avoid exceeding recommended duration for jump starting to prevent battery overheating.
6. Do not use the unit as a replacement for a vehicle battery.
7. Avoid complete discharge of the battery.
8. Do not jump start the engine while the unit is being charged.
9. Avoid attempting repairs yourself; contact a CLARKE dealer for assistance.
10. Keep body and clothing dry; work in damp areas only with proper insulation against electric shock.
11. Wear safety glasses when working with lead acid batteries.
12. If splashed by battery acid, flush the area with clean water and seek medical help if needed.

FAQ

• Q: Can I use the jump starter in rainy conditions?
  A: The device must only be used indoors or completely protected from the rain to ensure safety.

• Q: How long does it take to fully charge the jump starter?
  A: It takes approximately 6-7 hours to fully charge the jump starter from flat.

• Q: What should I do if the battery overheats during jump starting?
  A: To prevent battery damage, avoid exceeding the recommended duration for jump starting to prevent overheating.

• Q: How many cycles can the jump starter endure before needing a recharge?
  A: The jump starter can endure up to 1000 cycles before needing a recharge.

JUMPSTARTER
MODEL NO: JSM1000
PART NO: 6239025

OPERATING & MAINTENANCE INSTRUCTIONS

ORIGINAL INSTRUCTIONS

INTRODUCTION

Thank you for purchasing this CLARKE Jump-starter. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. Please keep these instructions in a safe place for future reference.

SPECIFICATIONS

Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice.

GENERAL SAFETY

WARNING: ALL LEAD ACID BATTERIES GENERATE HYDROGEN GAS DURING NORMAL OPERATION. THIS PROCESS INCREASES DURING A PERIOD OF RAPID DISCHARGE.
WARNING: HYDROGEN GAS AND BATTERY ACID (SULPHURIC ACID) CAN BE EXPLOSIVE, CORROSIVE TO SKIN, EYES AND HAIR, DAMAGING TO CLOTHING AND METALS, FLAMMABLE, POISONOUS TO BREATHE.

1. DO NOT leave the device exposed to the elements. Avoid direct sunlight, direct heat, rain/moisture etc.
2. The device must only be used indoors or completely protected from the rain. This also applies to any device being powered by the device.
3. DO NOT operate the device if any of the cables are damaged. Consult your CLARKE dealer for repair or replacement of the parts.
4. DO NOT operate the device if the case is damaged. Consult your CLARKE dealer or a qualified person for inspection and repair.
5. To prevent the battery from overheating and consequent damage, DO NOT exceed our recommendations for the duration of jump starting.
6. The unit is NOT designed to be used as a replacement for a vehicle battery.
7. NEVER allow the battery to become completely discharged.
8. NEVER jump start the engine whilst the unit is being charged.
9. NEVER attempt any repairs yourself. If you have a problem with the unit contact your local CLARKE dealer.
10. ALWAYS keep your body and clothing dry. NEVER work in a damp area without adequate insulation against electric shock.
11. ALWAYS wear safety glasses when working with lead acid batteries.
12. If splashed by battery acid, immediately flush the area of the splash with clean water. If a burning sensation is felt or any blistering occurs, seek medical help.
13. If battery acid comes into contact with the eyes, flush the eyes with clean water continuously and seek medical help.
14. ALWAYS ensure that there is air circulating around the unit when in use.
15. When not in use, store in a safe dry place out of reach of children.
16. NEVER allow the jumpstart leads, to touch each other or to touch the same metal object.
17. Ensure the vehicle battery posts and battery clamps are perfectly clean before use.
18. Connect the red clamp to the unearthed battery terminal first, (this is usually the positive (+ve) terminal and coloured RED); then connect the black clamp to the earthed battery terminal, (this is usually the negative (-ve) terminal and coloured BLACK).
19. ALWAYS wear suitable protective clothing and eye protection when working with lead acid batteries.
20. Only use this charger on lead acid batteries.

THE FOLLOWING SAFETY SYSMBOLS ARE SHOWN ON THE PRODUCT

ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general household waste but in accordance with the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal facility.

OVERVIEW

CHARGING THE DEVICE

CHARGING
You can charge the power pack using:

• The 12V DC car adapter.
• A device with a USB output socket.
• You can also use a USB-C to USB-C for fast charging (sold separately)

1. Switch the power pack off.
2. Plug the USB charging cable into the charger input socket and the other end to the car adapter socket using the supplied adaptor, or else to a suitable appliance.
   • If you are using the car adapter socket you will need to start the engine.
3. Disconnect the charger when fully charged.

THE LED CHARGE INDICATOR
Press the switch button to display the battery status of the device. The screen shows the % of power available and displays the output ports activated and in use. (100% is fully charged).

• When jumpstarting, the power indicator should show at least 80%. Recharge the device if required.
• The unit should hold a charge for 3-6 months but we recommend recharging every 3 months.

TO GET THE MAXIMUM LIFE FROM THE BATTERY

• Charge the jumpstarter before first use.
• DO NOT leave in a state of discharge.

OPERATION

WORK LIGHT

1. Push and hold the ON/OFF button for 3 seconds to turn the work light on.
2. Push the ON/OFF button again.
   • The worklight flashes on and off.
3. Push the ON/OFF button again.
   • The work light flashes with the morse code S-O-S pattern.
4. Push the ON/OFF button again to turn the work light off.

USB OUTPUT POWER SUPPLY
The USB sockets supply a maximum of 3A at 5V.

1. Plug the 3 in 1 USB cable into either of the USB sockets.
2. Connect the other end of the appropriate cable to your device(s).
3. Push the ON/OFF button to start supplying power.

SMART CABLE STATUS DISPLAY
The status of the device is shown by the LED display on the smart jumper cable as follows;

• Low voltage – Red LED solid
• Ready to start – Green LED solid
• Short circuit – Red LED solidand bleeping
• Reverse polarity – Red LED solidand bleeping
• Reverse charge – Red LED solidand bleeping
• Overheating – Red LED solidand bleeping
• Overcurrent – Green and red LED both solid

JUMP STARTING VEHICLES

WARNING: IT IS POSSIBLE THAT SOME ELECTRONIC EQUIPMENT COULD BE DAMAGED BY JUMP STARTING. ALWAYS CHECK WITH THE CAR MANUFACTURER’S HANDBOOK TO DETERMINE WHAT PRECAUTIONS IF ANY SHOULD BE TAKEN.
WARNING: FAILURE TO FOLLOW THE INSTRUCTIONS BELOW AND THE SAFETY INSTRUCTIONS ON PAGES 3/4 MAY RESULT IN PERSONAL INJURY, DAMAGE TO THE VEHICLE, OR BATTERY. NEVER ATTEMPT JUMP STARTING WITH DAMAGED CABLES.
CAUTION: TO AVOID DAMAGE TO THE VEHICLE’S ELECTRICAL SYSTEM, DO NOT USE THE JUMP STARTER ON A VEHICLE THAT HAS NO BATTERY INSTALLED.
CAUTION: DO NOT TOUCH POSTIVE AND NEGATIVE BATTERY CLAMPS TOGETHER.
NOTE: This device will not jumpstart a vehicle if the battery is very low. Check the indicators around the on/off button to determine the charge status.
NOTE: Make sure that the jumpstarter power pack is at least 80% charged (3 power indicator lights are lit) before you attempt to jumpstart.

CONNECTING THE JUMPER CABLE TO THE JUMPSTARTER

1. When jumpstarting, the power indicator lights must be lit. Recharge the device if required.
2. Lift the rubber plug and insert the duel pin connector of the jumper cable into the power pack.
   • The LEDs on the smart cable will flash to indicate the status.

CONNECTING THE JUMP START LEADS TO THE VEHICLE BATTERY
ALWAYS carry out the following preliminary checks before connecting the jump- start to the car battery:

• Switch off the vehicle ignition and ALL ancillary equipment (lighting,  radio etc.)
• Ensure the vehicle battery is rated at 12V and not damaged in any way.
• Ensure the area is well ventilated.
• Make sure that the battery terminals are clean and the clamps are firm and secure.
• If fitted, remove any vehicle battery filler plugs and check the electrolyte level. If necessary, top up with distilled water.
• Verify the jump starter is fully charged and recharge if needed.
• Make sure that the jumpstart is OFF.
• Turn off the vehicle ignition switch and all accessories (lights, radio, climate control, etc.)

1. Connect the red positive (+) clamp to the positive (+) battery terminal first. Take care the clamp does not touch any moving parts or fuel lines.
2. Connect the black clamp to the earthed battery terminal, (this is usually the negative (-ve) terminal and coloured BLACK) or to a suitable earthing point on the vehicle chassis ensuring the connections are firm and secure.

STARTING THE ENGINE

1. Push the ON/OFF button on the jumpstarter to start supplying power.
2. Crank the engine. The engine should start.
3. Switch or press the ignition to ‘start’. If the engine does not start SWITCH OFF the ignition and wait for at least 30 seconds before trying again.
4. If the vehicle does not start after 3 attempts, investigate any problems with the vehicle systems.
5. Once the engine is running, disconnect the earthed clamp FIRST i.e. that connected to the chassis or Negative terminal etc, then disconnect the Positive clamp from the battery terminal. You should remove the connections within 30 seconds of starting.
6. Leave the vehicle engine running for a while to let the alternator recharge the battery.
   • Take great care not to touch the red positive (+) clamp against the black negative (-) clamp.
7. Leave the jumpstarter for 30 minutes before re-charging following jumpstarting a vehicle.
   • If the battery is allowed to remain in a discharged state its life may be reduced.
   • The jumpstarter will power off automatically when no load is found.

TROUBLESHOOTING

If these remedies are unsuccessful, consult your CLARKE dealer.

DAILY CARE
Always ensure the cables & clamps are in good condition and the clamps are clean and corrosion free. If damaged they should be replaced. Keep the unit clean by wiping with a dry cloth. DO NOT use solvents as a cleaning agent.
Keep the unit fully charged at all times and always store away from direct sunlight, moisture or sources of extreme heat or cold.
NEVER attempt any repair unless your are a qualified technician. Your jump- start has been designed to give long and trouble free service. If, however, having followed the instructions in this booklet carefully, you encounter problems, take the unit to your local Clarke dealer.

GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.
This guarantee does not effect your statutory rights.

DECLARATIONS OF CONFORMITY

A SELECTION FROM THE VAST RANGE OF

PARTS & SERVICE: 0208 988 7400
Parts Enquiries Parts@clarkeinternational.com
Servicing & Technical Enquiries Service@clarkeinternational.com
SALES: UK 01992 565333 or Export 00 44 (0)1992 565335 Car Ke INTERNATIONAL Hemnall Street, Epping, Essex CM16 4LG www.clarkeinternational.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>