SPEKTRUM 2 in 1 Brushed 25 Amp ESC plus SLT Rx Combo Instruction Manual
- June 3, 2024
- SPEKTRUM
Table of Contents
SPEKTRUM 2 in 1 Brushed 25 Amp ESC plus SLT Rx Combo
NOTICE
All instructions, warranties, and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate
various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the
probability of property damage, collateral damage, and serious injury OR
create a high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the
probability of physical property damage AND a possibility of serious injury.
NOTICE : Procedures, which if not properly followed, create a possibility
of physical property damage AND a little or no possibility of injury.
WARNING : Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product
correctly can result in damage to the product, and personal property and cause
serious injury.
This is a sophisticated hobby product. It must be operated with caution and
common sense and requires some basic mechanical ability.
Failure to operate this Product in a safe and responsible manner could result
in injury or damage to the product or other property. This product is not
intended for use by children without direct adult supervision. Do not attempt
disassembly, use incompatible components, or augment the product in any way
without the approval of Horizon Hobby, LLC. This manual contains instructions
for safety, operation, and maintenance. It is essential to read and follow all
the instructions and warnings in the manual, prior to assembly, setup, or use,
in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
NOTICE: This product is only intended for use with unmanned, hobby-grade, remote-controlled vehicles and aircraft. Horizon Hobby disclaims all liability outside of the intended purpose and will not provide warranty service related thereto.
Specifications
Continuous current | 25A |
---|---|
Receiver Frequency | 2.4G (SLT) |
LiPo/NiMH Cells | 2S Lipo, 6 Cells NiMH |
BEC output | 3A /6V (Switch Mode) |
Battery Connector | EC2 |
Motor Connectors | 3.5mm Female Bullet Connectors |
Weight | 40g |
Dimensions | 36 x 25 x 15mm |
Compatible Motors | 380/390 |
Running Mode | Fwd/Rev/Br or Fwd/Rev |
Features
- Steering
- CH3 (available if using SLT3 ™ Transmitter)
- Selector for battery (LiPo or NiMH)
Components
A) ON/OFF Switch
B) +/- Battery connector, range 5-8.4V.
C) M+/M- Motor connector. Max current 25A
D) Bind Port
E) LiPo | NiMH Battery type selection
F) Running mode selection
G) LED
Factory Settings
Battery Type: LiPo
Running Mode: Fwd/Rev/Br
Binding
- Make sure the vehicle is secure with vehicle wheels off the ground.
- Insert the bind plug into the binding slot on the ESC/RX.
- Power on the vehicle. The LED light will flash rapidly.
- Power on SLT transmitter to bind to the vehicle. The LED light will stay ON when bound. If binding fails LED will turn OFF.
- Once bound, remove the bind plug before operation.
Note: If using the external receiver, follow bind instructions for that product.
Drag Brake Settings
When the ESC is powered ON the drag brake setting can be set using the jumper cap. The factory drag brake setting is 0%. The ESC has 5 levels of drag brake settings 0%(default)/25%/50%/75%/100.
Change the drag brake setting by following these steps:
- Power on ESC and ensure the ESC is ON and in “Fwd/Rev” mode.
- Remove “F/R” jumper cap and plug it back into the same location, this will add drag break strength level by one level.
- The ESC LED blinks to indicate strength level (1 blink=level 1, 2 blinks =level 2, and so on)
- When desired drag brake setting is achieved leave jumper cap in position to save setting.
Alarms
Battery Mode
When powered ON:
- 1 beep indicates NiMH mode. (Remove the jumper to place in NiMH mode)
- 2 beeps indicate LiPo mode. (Lipo Mode is the default mode)
Low Voltage Warning
The Low Voltage Warning feature is built into the receiver.
LiPo
When voltage goes below 6.6V protection mode is activated and motor power is
cut to 50%. Once the battery voltage drops below 6V the car will stop.
NiMH
When voltage goes below 5.2V protection mode is activated and motor power is
cut to 50%. Once the battery voltage drops below 5V the car will stop.
Fail-Safe
Built-in Fail Safe feature: When the receiver stops communication with the
transmitter, the ESC will stop throttle output. Steering output will maintain
the latest position.
ESC Troubleshooting
Problem | Possible Cause | Solution |
---|---|---|
No LED lights up after ESC is Powered ON | No power is drawn to the ESC; The | |
switch is broken | Check the connections between battery and ESC; Re-solder the |
connector if needed; Replace the ESC switch
LED OFF| The transmitter is OFF; The transmitter is not bound to ESC| Turn ON
the transmitter; Re-Bind the transmitter to the ESC.
LED blinks once a second| Battery voltage is low.| Change battery
The vehicle runs backwards when accelerating forward on the transmitter| The
direction setting of the throttle channel is incorrect in the transmitter or
the motor wires are connected incorrectly|
Reverse the direction of the throttle channel; Swap the wires between the ESC and motor.
The vehicle doesn’t reach full speed.| Incorrect TH D/R setting| Increase TH
D/R
Low voltage battery protection preventing full speed| Install a fully charged
battery
The vehicle doesn’t move but the LED indicators work normally
| Low voltage battery protection preventing vehicle movement| Install a fully
charged battery
The connection between ESC and motor is interrupted| Check the connection
between the motor and ESC
The motor is damaged| Install a new motor
The motor accelerates rapidly at the startup, but has lockout or cogging problem.
| The discharge capacity of the battery is not strong enough| Replace battery
with a battery with a larger discharge capability
The motor rotates too fast, and the gear ratio is too large| Use a motor with
lower RPM, or smaller pinion to lower the gear ratio
Something is wrong with the driveline of the vehicle.| Check the driveline of
the vehicle
1-Year Limited Warranty
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the
product purchased (the “Product”) will be free from defects in materials and
workmanship for a period of 1 year from the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage,(ii)
damage due to acts of God, accident, misuse, abuse, negligence, commercial
use, or due to improper use, installation, operation, or maintenance, (iii)
modification of or to any part of the Product, (iv) attempted service by
anyone other than a Horizon Hobby authorized service center, (v) Product not
purchased from an authorized Horizon dealer, (vi) Product not compliant with
applicable technical regulations, or (vii) use that violates any applicable
laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR
REPRESENTATION, AND HEREBY DISCLAIMS ANY
AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR
PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE
PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be
that Horizon will, at its option, either (i) service, or (ii) replace, any
Product determined by Horizon to be defective. Horizon reserves the right to
inspect any and all Product(s) involved in a warranty claim. Service or
replacement decisions are at the sole discretion of Horizon. Proof of purchase
is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFITS OR PRODUCTION
OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICTLIABILITY OR ANY OTHER THEORY OF
LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. Further, in no event shall the liability of Horizon exceed the
individual price of the Product on which liability is asserted. As Horizon has
no control over use, setup, final assembly, modification or misuse, no
liability shall be assumed nor accepted for any resulting damage or injury. By
the act of use, setup or assembly, the user accepts all resulting liability.
If you as the purchaser or user are not prepared to accept the liability
associated with the use of the Product, the purchaser is advised to return the
Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law
principles). This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. Horizon reserves the right
to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty
support or service. Once assembly, setup, or use of the Product has been
started, you must contact your local distributor or Horizon directly. This
will enable Horizon to better answer your questions and service you in the
event that you may need any assistance. For questions or assistance, please
visit our website at www.horizonhobby.com,
submit a Product Support Inquiry, or call the toll-free telephone number
referenced in the Warranty and Service Contact the Information section to
speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant with the
country you live and use the Product in, please use the Horizon Online The
service Request submission process is found on our website or call Horizon to
obtain a Return Merchandise Authorization (RMA) number. Pack the Product
securely using a shipping carton. Please note that original boxes may be
included, but are not designed to withstand the rigors of shipping without
additional protection. Ship via a carrier that provides tracking
and insurance for lost or damaged parcels, as Horizon is not responsible for
merchandise until it arrives and is accepted at our facility. An Online
Service Request is available at http://www.horizonhobby.com/content/
service-center_render-service-center.
If you do not have internet access, please contact Horizon Product Support to
obtain a RMA number along with instructions for submitting your product for
service. When calling Horizon, you will be asked to provide your complete
name, street address, email address and phone number where you can be reached
during business hours. When sending product into Horizon, please include your
RMA number, a list of the included items, and a brief summary of the problem.
A copy of your original sales receipt must be included for warranty
consideration. Be sure your name, address, and RMA number are clearly written
on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt
verifying the proof-of-purchase date. Provided warranty conditions have been
met, your Product will be serviced or replaced free of charge.
Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and
payment will be required without notification or estimate of the expense
unless the expense exceeds 50% of the retail purchase cost. By submitting the
item for service you are agreeing to payment of the service without
notification. Service estimates are available upon request. You must include
this request with your item submitted for service. Non-warranty service
estimates will be billed a minimum of ½ hour of labor. In addition, you will
be billed for return freight. Horizon accepts money orders and cashier’s
checks, as well as Visa, MasterCard, American Express, and Discover cards. By
submitting any item to Horizon for service, you are agreeing to Horizon’s
Terms and Conditions found on our website http://www.horizonhobby.com/content
/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging the return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Products for a period of 60 days from notification, after which they will be discarded.
Warranty and Service Contact Information
Country of Purchase| Horizon Hobby| Contact Information|
Address
---|---|---|---
United States
of America| Horizon Service Center
(Repairs and Repair Requests)|
servicecenter.horizonhobby.com/RequestForm/|
2904 Research Rd.
Champaign, Illinois
61822
USA
Horizon Product Support
(Product Technical Assistance)|
productsupport@horizonhobby.com.
877-504-0233
Sales| websales@horizonhobby.com
800-338-4639
European Union| Horizon Technischer Service|
service@horizonhobby.de| Hanskampring 9
D 22885 Barsbuttel, Germany
Sales: Horizon Hobby GmbH| +49 (0) 4121 2655 100
**FCC Information
**
Supplier’s Declaration of Conformity
2-in-1 ESC + SLT Rx Combo
(SPMXSE2025RX)
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION : Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may causeharmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Horizon Hobby, LLC
2904 Research Rd.,
Champaign, IL 61822
Email: compliance@horizonhobby.com
Web: HorizonHobby.com
IC Information
CAN ICES-3 (B)/NMB-3(B)
2-in-1 ESC + SLT Rx Combo
(SPMXSE2025RX)
This device contains license-exempt transmitter(s)/receivers(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following 2 conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Compliance Information for the European Union
EU Compliance Statement:
2-in-1 ESC + SLT Rx Combo
(SPMXSE2025RX) ; Hereby, Horizon Hobby, LLC declares that the device is
in compliance with the following: 2014/30/EU EMC Directive; RoHS 2 Directive
2011/65/EU;
RoHS 3 Directive – Amending 2011/65/EU Annex II 2015/863.
The full text of the EU declaration of conformity is available at the
following internet address: https://www.horizonhobby.com/content/support-
render-compliance.
EU Manufacturer of Record:
Horizon Hobby, LLC
2904 Research Road
Champaign, IL 61822 USA
EU Importer of Record:
Horizon Hobby, GmbH
Hanskampring 9
22885 Barsbüttel Germany
WEEE NOTICE:
****This appliance is labeled in accordance with European Directive
2012/19/EU concerning waste of electrical and electronic equipment (WEEE).
This label indicates that this the product should not be disposed of with
household waste. It should be deposited at an appropriate facility to enable
recovery and recycling. ©
2022 Horizon Hobby, LLC. SLT3, EC3, IC3, and the Horizon Hobby logo are
trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum
trademark is used with permission of Bachmann Industries, Inc.
References
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
- Ferngesteuerte Flugmodelle, Autos, Trucks, Hubschrauber, Boote und Fernsteuerungen | Horizon Hobby
- Horizon Hobby Service Center
- RC Cars, RC Trucks, RC Airplanes, Model Trains, and Slot Cars at Tower Hobbies
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
- RC Cars, RC Trucks, RC Airplanes, Model Trains, and Slot Cars at Tower Hobbies
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>