BRAND IC-50CS Wireless Car Charger User Manual
- August 15, 2024
- BRAND
Table of Contents
User Manual
Wireless Car Charger
Product Features
-
Built-in magnet and wireless charging transmitter coil, placing the magnetic phone will automatically adsorption and start wireless charging.
-
Built-in smart semiconductor chilling plate and cooling fan, the fan will start working when the wireless charging starts,the chilling plate cools the wireless charging coil and the phone surface simultaneously to improve the wireless charging efficiency.
The semiconductor chilling plate stops working when the phone is removed. -
Standby mode: The ice blue light keeps on.
-
Charging mode: The ice blue breathing light flashing. After removing the phone for 30 seconds, the fan will stop rotating and the colorful lights go out.
-
FOD function: when put metal or magnet objects on the charger, the wireless charging stops working and the phone does not charge.
-
Perfect protective function based on over-voltage, over-current, over-temperature and short-circuit protection.
Specifications
Input:DC 12V/2.5A,9V/2A,5V/2A
Output:15W/10W/5W
Product Standard:Qi
Charging Distance: ≤ 10mm
Charging Efficiency: ≤ 80%
Product Dimension:60*42.3°95mm
Product Material:ABS+Tempered Glass
Product Parts Description
Quick wireless charging requires QC or PD adapters.
Product Operating Guide
- Please make sure the product connect to the power before using.
- The ice blue light keeps on if connected with power.
- The ice blue light will flashes and the product stop charging when the current is too large or there is foreign object. Do not wireless charging the phone if similar situation happened.
- Please purchase the wireless receiver module or case separately (Not included in the product) if your phone do not support wireless charging.
Attention
- Please do not vigorously extrude or collide.
- Please do not dismantle or put it into fire or water when the product is power on,to avoid short circuit or leakage.
- Please do not use it in severely high temperature,high humidity or corrosive environment,to avoid damage to the circuit leakage.
- Please do not put the magnetic strip or chip card (Such as ID card, bankcard etc.)on the charging pad to avoid to cause magneticcard lose efficacy.
- Please do not put the metal (Such as coin etc.) on the charging pad when charging,to avoid damage from heating.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate
radiofrequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>