CSC LED CWP05 Wall Packs Installation Guide

CSC LED CWP05 Wall Packs\

Specifications

• Product Name : CWP05 Wall Packs
• Manufacturer: CSC LED
• Power Source: Electric
• Wattage: Variable (Adjustable)
• Color Temperature: Selectable

Product Usage Instructions

Installation Warnings

• Risk of Burn: Disconnect power and allow the fixture to cool before handling or servicing.
• Risk of Personal Injury: The fixture may become damaged and/or unstable if not installed properly.

Disclaimer
CSC LED assumes no liability for damages or losses due to improper installation, handling, or use of this product.

Safety Instructions
This fixture must be wired following the National Electrical Code and local codes. Proper grounding is essential for personal safety.

Important Notes

• Do not relocate the green ground wire.
• Apply silicone to prevent water ingress to avoid voiding the warranty.

Installation Steps

1. Remove screws on the side of the luminaire to open it.
2. Remove the front cover of the fixture.
3. Wire the fixture correctly and ensure installation is complete before turning on the power switch.

WARNINGS

RISK OF FIRE, ELECTRICAL SHOCK, CUTS, OR OTHER CASUALTY HAZARDS
Installation and maintenance of this product must be performed by a qualified electrician. This product must be installed by the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.

RISK OF FIRE AND ELECTRIC SHOCK
Make certain power is OFF before starting installation or attempting any maintenance. Disconnect power at the fuse or circuit breaker.

RISK OF FIRE
Refer to the product label for specific minimum supply conductor requirements.

RISK OF BURN
Disconnect the power and allow the fixture to cool before handling or servicing.
RISK OF PERSONAL INJURY
The fixture may become damaged and/or unstable if not installed properly.

DISCLAIMER OF LIABILITY
CSC LED assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling, or use of this product.

• NOTICE : Green ground wire was provided in the proper location. Do not relocate.
• SAFETY: This fixture must be wired by the National Electrical Code and applicable local codes and ordinances. Proper grounding is required to ensure personal safety. Carefully observe the grounding procedure under the installation section.
• APPLICATIONS : This lighting fixture is designed for outdoor lighting services, and should not be used in areas of limited ventilation or inside high ambient temperature enclosures. It must be stored in a dry location before installation. Do not expose the lighting fixture to rain, dust, or other environmental conditions before installation and insertion of photo control or shorting cap (if so equipped). The best results will be obtained if installed and maintained according to the following recommendations.

ATTENTION RECEIVING DEPARTMENT : Note the actual fixture description of any shortage or noticeable damage on the delivery receipt. File claim for common carrier (LTL) directly with the carrier. Claims for concealed damage must be filed within 15 days of delivery. All damaged material, complete with original packing must be retained.

IMPORTANT: Apply a bead of silicone to the top and side of the fixture where it meets the wall or mounting surface to prevent water ingress from the back of the fixture. FAILURE TO DO SO WILL VOID THE WARRANTY.

WIRING DIAGRAM

JUNCTION BOX INSTALLATION

PLEASE ENSURE THAT THE LUMINAIRE IS CORRECTLY WIRED AND INSTALLATION IS COMPLETE BEFORE TURNING THE POWER SWITCH ON.

1. Remove both screws on the side of the luminaire with a screwdriver. (Fig. 1.1)

2. Open the fixture, and remove the front cover of the fixture. (Fig. 1.2)
   Please make sure that the quick disconnect plug is detached before removing the front cover.

3. Use an electric drill to drill the mounting holes on the mounting plate of the luminaire. (Fig. 1.3)

4. Peel and stick the foam pad to the back of the mounting plate. (Fig. 1.4)

5. Use a screwdriver to remove the plug. (Fig. 1.5)

6. Affix the mounting plate with screws (Fig. 1.6) and connect the wires (L, N, G) to the power supply. (Fig. 1.7)

7. Attach the front cover of the luminaire back to the mounting plate (Fig. 1.8) and tighten both screws on the side of the luminaire (Fig. 1.9). Remember to reconnect the quick disconnect plug before closing the luminaire.

DIRECT WALL MOUNT INSTALLATION

PLEASE ENSURE THAT THE LUMINAIRE IS CORRECTLY WIRED AND INSTALLATION IS COMPLETE BEFORE TURNING THE POWER SWITCH ON.

1. Remove both screws on the side of the luminaire with a screwdriver. (Fig. 2.1)

2. Open the fixture, and remove the front cover of the fixture. (Fig. 2.2)
   Please make sure that the quick disconnect plug is detached before removing the front cover.

3. Drill mounting holes with an electric drill and insert the anchor into the wall. (Fig. 2.3)

4. Peel and stick the foam pad to the back of the mounting plate. (Fig. 2.4)

5. Remove the plug (Fig. 2.5) and affix the mounting plate with screws. (Fig. 2.6)

6. Connect the luminaire’s wires (L, N, G) to the power supply. (Fig. 2.7)

7. Attach the front cover of the luminaire back to the mounting plate (Fig. 2.8) and tighten both screws on the side of the luminaire (Fig. 2.9). Remember to reconnect the quick disconnect plug before closing the luminaire.

WATTAGE AND COLOUR SELECTABLE SWITCH

IMPORTANT : TURN OFF THE POWER BEFORE ADJUSTING THE POWER AND COLOUR TEMPERATURE.

1. The power and color temperature switch is located on the side of the luminaire. Remove the plug to access the switch. (Fig. 3.1 & Fig. 3.2)
2. After adjusting to your desired setting, please put the plug back in place and tighten it.

PHOTOCELL INSTRUCTIONS

The luminaire comes pre-installed with a photocell (Fig. 4.1). If the photocell is not needed, unplug the wires connected to the photocell. (Fig. 4.2)

CSC LED REWARDS

• Earn points when you purchase CSC LED products from your preferred electrical wholesaler.
• Redeem your points for gift cards and other reward items!

www.csc-led.com/rewards

MORE INFORMATION

• www.csc-led.com
• info@csc-led.com

FAQ

• Q: What should I do if I notice damage on delivery?
  • A: Note the damage on the delivery receipt and file a claim with the carrier within 15 days. Retain all damaged material and original packing.
• Q: Where is the power and color temperature switch located?
  • A: The switch is located on the side of the luminaire. Remove the plug to access it.

References

• LED Commercial Lighting and Lighting Controls | Current - GLI Brands

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>