TIMEX 04K-096000 LCD Analog Digital Watch User Guide

TIMEX 04K-096000 LCD Analog Digital Watch

Safety Instructions

• INGESTION HAZARD: This product contains a button cell or coin battery.
• DEATH or serious injury can occur if ingested.
• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
• KEEP new and used batteries OUT OF REACH of CHILDREN
• Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
• Even used batteries may cause severe injury or death.
• Call a local poison control center for treatment information.
• Battery type: lithium metal, CR2025.
• Nominal battery voltage: 3.0 V
• Non-rechargeable batteries are not to be recharged.
• Do not force discharge, recharge, disassemble, heat above 158°F (70ºC) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
• Ensure the batteries are installed correctly according to polarity (+ and -).
• Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon zinc, or rechargeable batteries.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

Register your product at https://www.timex.com/product-registration.html

TIMEX INTERNATIONAL WARRANTY
http://www.timex.com/productWarranty.html

FEATURES AND BASIC OPERATIONS

1. LCD Analog (Hands) and Digital Timekeeping with Hours, Minutes, Seconds – AM/PM/24-Hour Format
2. Daily Alarm and Hourly Chime
3. 24-Hour Stopwatch with Split time
4. 60-Minute Countdown Timer
5. Dual Time (2nd Time Zone)

TIME

To set Time and Date

1. Press MODE repeatedly until the Time is shown with the Seconds flashing.

2. Press LAP/RESET to set Seconds to zero.
   NOTE : If Seconds are greater than 30, the Minutes will increase by one.

3. Press START/STOP to set Minutes, as indicated by its flashing. Press LAP/RESET to advance the Minutes setting. Press and hold to increment quickly.

4. Press START/STOP to set Hours, as indicated by its flashing. Press LAP/RESET to advance the Hours setting to AM or PM. Press and hold to increment quickly.
   NOTE : There is ONLY an indicator for PM hours.

5. Press START/STOP to set the Date (01-31), as indicated by its flashing. Press LAP/RESET to advance the Date setting. Press and hold to increment quickly.

6. Press START/STOP to set the Month number (01-12), as indicated by its flashing. Press LAP/RESET to advance the Month setting. Press and hold to increment quickly.

7. Press START/STOP to set the Day setting (SUN-SAT), as indicated by its flashing. Press LAP/RESET to advance the Day setting. Press and hold to increment quickly.

8. Press MODE to exit Time Set.

9. To switch from AM/PM to 24-Hour time format, press and hold START/ STOP for 4 seconds. Press and hold START/STOP for 4 seconds to reverse the format change.
   NOTE : A “24HR” indicator in the bottom right corner of the display confirms the change. There is ONLY an indicator for PM hours.

DUAL TIME
To set the time for a Second Time Zone – shown on the LCD Analog watch face.

1. Press MODE until the indicator is next to the “DUAL T” on the display.

2. Press START/STOP. The Hour Hand on the watch face can be seen flashing.

3. Press LAP/RESET to advance the Hour Hand around the watch face setting to AM or PM. Press and hold to increment quickly.
   NOTE : There is ONLY an indicator for PM hours.

4. Press START/STOP. The Minute Hand on the watch face can be seen flashing.

5. Press LAP/RESET to advance the Minute Hand around the watch face. Press and hold to increment quickly.

6. Press START/STOP to exit Dual Time Set, and the Second Hand will appear on the watch face.
   NOTE : In Dual Time mode, the AM/PM indication is tied to the Analog time.

ALARM
To turn on/off the Daily Alarm, or to turn on/off the Hourly Chime

1. Press MODE until the indicator is next to the “ALARM” on the display.
   NOTE : The alarm setting is tied to the primary time zone.

2. Press START/STOP and LAP/RESET simultaneously and repeatedly to enable the Alarm , enable the Chime , disable the Alarm, and disable the Chime.
   NOTE : You can turn the Alarm on/off without changing the Chime setting by pressing LAP/RESET.

To set a Daily Alarm – shown on the LCD Analog watch face

1. Press MODE until the indicator is next to the “ALARM” on the display.
   NOTE : The alarm setting is tied to the primary time zone

2. Press START/STOP. The Hour Hand on the watch face can be seen flashing.

3. Press LAP/RESET to advance the Hour Hand around the watch face setting to AM or PM. Press and hold to increment quickly.
   NOTE : There is ONLY an indicator for PM hours.

4. Press START/STOP. The Minute Hand on the watch face can be seen flashing.

5. Press LAP/RESET to advance the Minute Hand around the watch face. Press and hold to increment quickly.

6. Press START/STOP to exit Alarm Set mode.

7. When the alarm sounds, press ANY button to silence the alert, or it will stop after 20 seconds.
   NOTE : The alarm will sound the next day at the same time unless you go into Alarm Mode and press LAP/RESET to turn it off.

TIMER
To set a countdown for up to 60 minutes – shown on the LCD Analog watch face

1. Press MODE until the indicator is next to the “TIMER” on the display. If the Timer shows any previous setting, the indicator will flash.
2. Press LAP/RESET repeatedly to increase the number of Minutes for the countdown.
   NOTE : If you go past the desired number of minutes, you will have to continue to press LAP/RESET to wrap around the setting display.

To use the countdown timer – shown on the LCD Analog watch face

1. Press MODE until the indicator is next to the “TIMER” on the display. If the Timer shows any previous setting, the indicator will flash.
   NOTE : If no setting is shown, press LAP/RESET to restore the previously set countdown (or refer to the Timer Set instructions).

2. Press START/STOP to begin the countdown. The watch face will show Seconds counting down along its outer edge.

3. Press START/STOP to pause the timer.

4. Press START/STOP to resume the countdown, or press LAP/RESET to reset the timer to its previous setting.

5. When the countdown ends, the alert will sound for 5 seconds, or press ANY button to silence it.
   NOTE : The alert will sound even if you are not in TIMER mode.

STOPWATCH
Use this function for recording elapsed time up to 24 hours.

1. Press MODE until the indicator is next to the “STOP” on the display.
   NOTE : The current time of day is shown on the LCD Analog watch face.

2. Press START/STOP to start the stopwatch. It will be shown in the lower digital display.

3. With the stopwatch running, press LAP/RESET to record and show the Split time. The stopwatch will continue timing in the background.
   NOTE : A “split” is the elapsed time (from the beginning) to the point it was recorded.

4. Press LAP/RESET to release the display and show the current running stopwatch time.

5. Press LAP/RESET to record another Split time.

6. Press START/STOP to pause the stopwatch.
   NOTE : If the stopwatch is paused when the display is showing a Split time, the displayed elapsed time is updated.

7. Either press START/STOP to resume timing, or press LAP/RESET to reset the stopwatch to zero.

DISPLAY LIGHT FEATURE
Press the LIGHT button to activate the display light.

HOW TO ADJUST BRACELET SLIDING CLASP BRACELET

1. Open locking plate.
2. Move clasp to desired bracelet length.
3. Exert pressure while holding locking plate and slide clasp back and forth until it engages in grooves on underside of bracelet.
4. Press locking plate down until it snaps closed. Clasp can be damaged if excessive force is used.

WATER AND SHOCK RESISTANCE
This watch is water-resistant to a 30-meter rating.

pounds per square inch absolute

WARNING : TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY BUTTONS UNDER WATER.

1. Watch is water-resistant only as long as lens, push buttons and case remain intact.
2. Watch is not a diver watch and should not be used for diving.
3. Rinse watch with fresh water after exposure to salt water.
4. Shock-resistance will be indicated on watch face or case back. Watches are designed to pass ISO test for shock-resistance. However, care should be taken to avoid damaging crystal/lens.

BATTERY

The watch button cell or coin battery is not intended to be replaced by a consumer. Only a jeweler or other professional is to replace the battery.

TIMEX INTERNATIONAL WARRANTY
http://www.timex.com/productWarranty.html

©2024 Timex Group USA, Inc. TIMEX and INDIGLO are registered trademarks of Timex Group B.V. and its subsidiaries.

References

• Watches from Timex | Digital, Analog, & Water Resistant Watches | Timex EU

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>