TIMEX Diamond Collection Watch User Guide

Diamond Collection Watc

WARNING

• INGESTION HAZARD: This product contains a button cell or coin battery.
• DEATH or serious injury can occur if ingested.
• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
• KEEP new and used batteries OUT OF REACH of CHILDREN
• Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
• Even used batteries may cause severe injury or death.
• Call a local poison control center for treatment information.
• Battery type: silver oxide SR516SW.
• Nominal battery voltage: 1.5 V
• Non-rechargeable batteries are not to be recharged.
• Do not force discharge, recharge, disassemble, heat above 140°F (60°C) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
• Ensure the batteries are installed correctly according to polarity (+ and -).
• Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon zinc, or rechargeable batteries.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

Congratulations on purchasing your TIMEX® watch.
Please read these instructions carefully to understand how to operate your Timex timepiece.
Your watch may not have all of the features described in this booklet.
For more information, and to register your product please visit: www.timex.com

HOW TO START YOUR WATCH

To start your watch remove the plastic guard from under the crown, then press the crown in against the case. The second hand will begin advancing in one- second intervals.

WATER AND SHOCK RESISTANCE

If your watch is water-resistant, meter marking (WR_M) is indicated.

WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY BUTTONS OR PULL OUT THE CROWN UNDER WATER UNLESS YOUR WATCH IS INDICATED AS 200 METER WATER- RESISTANT.

1. Watch is water-resistant only as long as crystal, crown and case remain intact.
2. Watch is not a diver watch and should not be used for diving.
3. Rinse watch with fresh water after exposure to salt water.
4. Shock-resistance will be indicated on the watch face or caseback. Watches are designed to pass ISO test for shock-resistance. However, care should be taken to avoid damaging the crystal.

To Set Time/Day/Date

TO SET TIME:

1. PULL crown all the way out and turn to correct time.
2. Push crown in to restart. For screwin setting crown, push crown in while turning CLOCKWISE to tighten.

TO SET DAY:

1. PULL crown to “middle” position and turn CLOCKWISE until correct day appears. If day does not change, pull crown to “out” position and turn CLOCKWISE or COUNTERCLOCKWISE through necessary number of 24 hour periods until correct day appears.

TO SET QUICK DATE® FEATURE:
3-Position Crown:

1. Pull crown to “Middle” position and turn CLOCKWISE or COUNTERCLOCKWISE
   until correct date appears.
   2-Position Crown:
2. Pull crown to “OUT” position and turn CLOCKWISE until date changes.
   Repeat until correct date appears. Adjust date when month has less than 31 days. Push crown in when finished.

HOW TO ADJUST BRACELET

(Variations of the following bracelet sections apply to all watch models).
SLIDING CLASP BRACELET

1. Open locking plate.
2. Move clasp to desired bracelet length.
3. Exert pressure while holding locking plate and slide clasp back and forth until it engages in grooves on underside of bracelet.
4. Press locking plate down until it snaps closed. Clasp can be damaged if excessive force is used.

FOLDOVER CLASP BRACELET

1. Find spring bar that connects bracelet to clasp.
2. Using a pointed tool, push in spring bar and gently twist bracelet to disengage.
3. Determine wrist size, then insert spring bar in correct bottom hole.
4. Push down on spring bar, align with top hole and release to lock in place.

BRACELET LINK REMOVAL
Removing Links:

1. Place bracelet upright and insert pointed tool in opening of link.
2. Push pin forcefully in direction of arrow until link is detached (pins are designed to be difficult to remove).
3. Repeat until desired number of links are removed.

Re-assembly:

1. Rejoin bracelet parts.
2. Push pin back into link in opposite direc- tion of arrow.
3. Press pin down securely into bracelet until it is flush.

Warranty

BATTERY
The watch button cell or coin battery is not intended to be replaced by a consumer. Only a jeweler or other professional is to replace the battery.
TIMEX INTERNATIONAL WARRANTY
www.timex.com/pages/warranty-repair

© 2024 Timex Corporation. TIMEX and QUICK DATE are registered trademarks of Timex Corporation.

References

• Watches from Timex | Digital, Analog, & Water Resistant Watches | Timex US
• Watches from Timex | Digital, Analog, & Water Resistant Watches | Timex EU

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>