TECHPUNT 70Mai Dash Cam Omni User Manual
- August 13, 2024
- TECHPUNT
Table of Contents
70mai Dash Cam Omni
User Manual
Product overview
Please read this manual carefully before using the product and keep it in a safe place.
- Power button
- Upper button
- Lower button
- Adhesive sticker
- Mount
- Microphone
- Display screen
- Camera
- Speaker
- Power port
- Round-shape indicator
- Tripod head
Specifications
Product: Dash Cam
Model: X200
Resolution: 1920 × 1080
Lens: FOV 140°/ F1.5
Battery capacity: 300 mAh
Input: 5 V 2 A
Power supply: Car cigarette lighter
Battery type: Lithium polymer battery
Packing list
- Dash Cam × 1
- Power cord × 1
- Car charger × 1
- Mount(Pre-installed on the dash cam) × 1
- Electrostatic sticker × 2
- Wiring crowbar × 1
- Adhesive sticker × 2 (With 1 piece pre-applied to the mount)
- User manual × 1
Note: Illustrations of the product, accessories, and user interface in the user manual are for reference purposes only. The actual product and functions may vary due to product enhancements.
Installation
-
Selecting mounting position Mount the dash cam on either of the recommended positions of front windshield as appropriate:
1. Near the center of rearview mirror;
2. On the front of the passenger seat.
Notes: Make sure the camera is below the level line of the rearview mirror.
Attach the electrostatic sticker on the selected position, with the gap image facing upwards. Press the sticker to remove air bubbles out.
Keep windshield clean and dry without liquid residue to prevent the sticker from losing adhesion and dash cam from dropping. -
Installing the dash cam Paste the dash cam on the electrostatic sticker.
Make sure the gap on the adhesive sticker aligns with that on the electrostatic sticker and the display screen faces the car interio -
Routing cable
Route the power cord to the cigarette lighter and connect to power. Notes:
Use the included crowbar to hide the power cord underneath the vehicle’s headliner and rubber seal along the A-pillar.
Depending on the vehicle, the cigarette lighter socket may be located in a different position. The figure provided is for reference only. -
Adjusting the dash cam angle
Hold the dash cam and turn the dash cam up and down to adjust the dash cam angle based on the preview screen.
Installing/uninstalling the mount
The mount is pre-installed on the dash cam. If you need to uninstall it,
follow the steps below:
Uninstalling the mount: Hold the dash cam and screw it clockwise and then
the dash cam will separate with the mount.
Installing the mount:
- Align the microphone with the big locating point on the right of the mount, and then the dash cam is inserted to the mount.
- Hold the dash cam and screw counterclockwise until the microphone is aligned with the big locating point on the left of the mount, and then the dash cam is tightened up with the mount.
Downloading 70mai app
This product needs to be used in conjunction with the 70mai app. You can
download and install the app by scanning the QR code or finding “70mai” in the
app store.
Note: Android 5.0 & iOS 11.0 or above is required to connect to the dash
cam’s Wi-Fi hotspot with a mobile phone.
https://www.70mai.com/download/
User guide
For more on product functions and FAQs, please see the user guide by scanning
the QR code.
https://help.70mai.asia/1947.html
Accessories (optional)
This product can also be used with the 70mai 4G Hardwire Kit. Scan the QR code
to obtain the user guide for the 70mai 4G Hardwire Kit.
https://help.70mai.asia/1472.html
Precautions
Before using the dash cam, please read all the precautions and the user guide
to ensure correct and safe use.
The dash cam is intended to assist drivers with the purpose of recording the
environment outside the vehicle. The dash cam does not guarantee the user s
driving safety. We shall not be held liable for any accident, damage, or loss
of information caused by operating the dash cam while driving. Due to
differences in vehicle conditions, driving style, driving environment, etc.,
some functions may not work properly. A power failure, usage in environments
outside the normal operating temperature or humidity range, or a collision may
cause the dash cam to function abnormally. There is no guarantee that this
dash cam will function normally under all circumstances. Videos recorded by
this dash cam are for reference only. The eMMC (Embedded Multi Media Card) is
built in the dash cam for storage. You can find the memory capacity
information on the label of the dash cam and product box. Install this dash
cam correctly, and do not block the driver’s line of sight, nor block the
vehicle’s airbag, in order to avoid product failure or personal injury. Use
the included car charger, power cord, and other accessories in order to avoid
product failure due to nonconformance. We shall not be held liable for any
loss or damage caused by the use of a non-genuine car charger or power cord.
The dash cam is equipped with a built-in battery that cannot be removed. Do
not disassemble the dash cam. Do not expose batteries or battery packs to
sunlight, fire, or environments where the ambient temperature is extreme heat.
There is a risk of explosion if the battery is incorrectly installed,
therefore only use and replace with the same or an equivalent type of battery.
Keep the dash cam away from water drops or splashes. Keep the device dry to
avoid battery failure. If the battery becomes deformed, swollen, or starts
leaking during use or storage, stop using the dash cam immediately in order to
avoid safety issues, and contact after-sales service. Never wash the dash cam
with chemical solvent or cleaner.
Keep the dash cam away from any strong magnetic fields, as they may cause
damage to the dash cam. Do not use the dash cam in environments with
temperatures over 60°C or below -10°C. After working for a period of time, the
case temperature of the dash cam will rise, please be careful when touching
it. Only use this dash cam within the scope permitted by law.
Regulatory compliance information
WEEE information
All products bearing this symbol are waste electrical and electronic
equipment (WEEE as in directive 2012/19/EU) which should not be mixed with
unsorted household waste. Instead, you should protect human health and the
environment by handing over your waste equipment to a designated collection
point for the recycling of waste electrical and electronic equipment,
appointed by the government or local authorities. Correct disposal and
recycling will help prevent potential negative consequences to the environment
and human health. Please contact the installer or local authorities for more
information about the location as well as terms and conditions of such
collection points.
EU declaration of conformity
**** The manufacturer hereby, declares that this equipment is in compliance
with the applicable Directives and European Norms, and amendments. The full
text of the EU declaration of conformity is available at the following
internet address: https://help.70mai.asia/1193.html
Cautions
Disposal of a battery into fire or a hot oven, or mechanically crushing or
cutting of a battery, that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment
that can result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas. This device is equipped
with a built-in battery that cannot be removed or replaced. Do not disassemble
or modify the battery by yourself. Replacement of a battery with an incorrect
type can defeat a safeguard (for example, in the case of some lithium battery
types).
FCC caution
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator & your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter. FCC ID: 2AOK9-X200
ISED compliance statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
ISED Radiation Exposure statement
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm between the radiator and your body.
IC: 28033-X200
Hereby, 70mai Co.,Ltd. declares that the radio equipment type X200 is in
compliance with Radio Equipment Regulations 2017. The full text of the UKCA
declaration of conformity is available at the following internet address:
****https://help.70mai.asia/2145.html
Scan the QR code and email us at help@70mai.com
View the User guide for product functions and FAQs.
https://help.70mai.asia/1947.html
Service: help@70mai.com
For further information, please go to www.70mai.com
Manufacturer: 70mai Co., Ltd.
Address: Room 2220, Building 2, No. 588 Zixing Road, Minhang District,
Shanghai, China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>