Firecell FC-200-002 Wireless Call Point Installation Guide
- June 4, 2024
- firecell
Table of Contents
Wireless Call Point (KAC Front)
Installation Guide
| Part no | Product Description |
|---|---|
| FC-200-002 | Wireless Call Point (KAC Front) |
| 5-5201/EN54 | Replacement Element |
Pre-installation
Installation must conform to applicable local installation codes and should only be installed by a fully trained competent person.
- Ensure that the device is installed as per the site survey.
- The use of a non-metallic spacer should be considered if mounting the device onto a metal surface.
- Do NOT Press the Log On button on a pre-programmed device, as this will cause communication with the Control Panel to be lost. Should this happen, delete the device from the system and add it back on.
- This device contains electronics that may be susceptible to damage from Electrostatic Discharge (ESD). Take appropriate precautions when handling electronic boards.
Components
- Protective cover
- Fixing screw
- Wireless call point
- Mounting plate
Fix mounting plate
- Remove the mounting plate from the wireless call point. See Step 5 for more information on unlocking the device.
- Ensure the mounting plate is fitted in the orientation shown.
- Use both mounting holes.
- Use suitable fasteners and fixings.
Power device
- When fitting / replacing batteries; observe correct polarity, using only specified batteries.
- Connect the power jumper across the PIN header.
- Once powered, reassemble the device.
Device locking
To open the call point, loosen the fixing screw, then slide the call point up,
away from the mounting plate.
When reassembling, observe the hinged connection located on the device’s top
edge first, prior to closing the unit.
Finally, lock the call point into the mounting plate by tightening the fixing
screw.
Configuration
The device’s loop address is configured within the user interface’s menu structure.
- Refer to the programming manual for full programming details.
FireCell = MK98
Fusion = TSD062
WSM = TSD143
Free to download from www.emsgroup.co.uk
Testing and resetting
Replacing elements
Specification
| Operating temperature | -10 to +55 °C |
|---|---|
| Storage temperature | 5 to 30 °C |
| Humidity | 0 to 95% non-condensing |
| Supply | 6x AA alkaline (Panasonic LR6AD Powerline /Varta 4006 Industrial) |
CAUTION!
The fitting of an incorrect battery type invalidates the product certification
and may result in poor performance.
| IP rating | IP24 |
|---|---|
| Operating frequency | 868 MHz |
| Output transmitter power | Auto-adjusting 0 to 14 dBm (0 to 25 mW) |
| Dimensions (W x H x D) | 89 x 92 x 70 mm |
| Weight | 0.40 kg |
| Location | Type A: For indoor use |
Regulatory information
Manufacturer| Carrier Manufacturing Polska Sp. Z o.o. Ul. Kolejowa 24. 39-100
Ropczyce, Poland
---|---
Year of manufacture| See device serial number label
Certification| 10
Certification
body| 905
CPR DoP| 0359-CPR-0038
Approved to| EN54-11:2001. Incorporating Amendment No. 1 and Corrigendum No.
- Fire detection and fire alarm
systems. Part 11: Manual call points.
EN54-25:2008. Incorporating corrigenda September 2010 and March 2012. Fire detection and fire alarm
systems. Part 25: Components using radio links.
European Union
directives| EMS declares that this device is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address: www.emsgroup.co.uk
| 2012/19/EU (WEEE directive):
Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see www.recyclethis.info
Dispose of your batteries in an environmentally friendly manner according to your local regulations.
©2021 EMS Ltd. All rights reserved
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>