FVCO SP0207B Sprinter Side Ladder for Low Roof Installation Guide
- August 9, 2024
- FVCO
Table of Contents
FVCO SP0207B Sprinter Side Ladder for Low Roof
Specifications
- Product: Sprinter Van Side Ladder – Low Roof
- Model: SP0207B
Product Usage Instructions
Before Installation
Inspect the product and packaging upon delivery. Ensure all parts and hardware
are accounted for. Contact support if anything is missing.
Package Contents
- Ladder Upper Half: Qty 1
- Ladder Lower Half: Qty 1
- Mounting Plate: Qty 1
- Support Bracket: Qty 1
- Bayonet Coupler: Qty 2
Hardware
Installation Steps
- Step 01: Layout and Install Prep
- Step 02: Side Ladder Assembly
- Step 03: Side Ladder Fitting
- Step 04: Side Ladder Alignment
FAQ:
Q: How long does it take to install the Sprinter Van Side Ladder?
A: The estimated time for installation is 1 hour, but additional help is
recommended for some steps.
INSTALLATION GUIDE
SPRINTER VAN SIDE L ADDER – LOW ROOF
SP0207B
TOOLS REQUIRED
- + 9/16” WRENCH OR SOCKET
- + 7/16” WRENCH OR SOCKET
- + 7/32” ALLEN WRENCH
- + 5/32” ALLEN WRENCH
- + POWER DRILL
- + 1/2” DRILL BIT
- + 1/8” DRILL BIT
INSTALL INFO
TIME TO INSTALL THIS PRODUCT: 1 HOUR Additional help is suggested for a few of
the install steps.
BEFORE YOU START
Please inspect the product and packaging upon delivery to ensure there are no
issues and that all parts and hardware are accounted for.
Contact us ASAP if anything is missing at:
support@flatlinevanco.com
BEFORE YOU START
All Flatline Van Co products must be properly assembled and secured before attaching to your vehicle. Improper attachment could result in an automobile accident, and could cause serious bodily injury or death to you or to others involved. You are responsible for assembling and securing Flatline Van Co products to your vehicle, checking the mounting points and attachments prior to use, and regularly inspecting the products for wear and or damage. We always recommend you use a professional to install any aftermarket accessories to your vehicle. If you have no mechanical experience and are not thoroughly familiar with the installation procedures, you must have the product installed by a professional installer or other qualified persons. The responsibility is yours and must be taken seriously for everyone’s safety.
PACKAGE CONTENTS
HARDWARE
INSTALL
STEP | 01 LAYOUT AND INSTALL PREP
- Identify Van Configuration: There could be any number of accessories mounted to your van that may inform the way you approach the install of your Side Ladder (Roof Racks, Side Steps, Water Tanks, etc.) See FIG 1 for key areas that will need accessed.
NOTE – The van pictured is a 144” High Roof Sprinter, but the same principles apply to the 170” and 144” Low Roof as well.
NOTE – You may need to loosen or temporarily remove mounted accessories to gain sufficient access to the Roof Rail and Pinch Seam of your van.
STEP | 02 SIDE LADDER ASSEMBLY
- Install Bayonets to Top Ladder Half: Find the Top Half of the Side Ladder and insert Bayonets as shown in FIG 4. Secure using (2ea) 1/4-20 x 0.75 Flanged Button Head Hex Drive Screws and Loctite.
- Attach Bottom Ladder Half: Find the Bottom Half of the Side Ladder and attach to protruding Bayonets using (2ea) 1/4-20 x 0.75 Flanged Button Head Hex Drive Screws and Loctite as shown in FIG 5-7.
STEP | 03 SIDE LADDER FITTING
-
Roof Rail Nuts: Slide in Rail Nuts to location of install along the Roof Rail (FIG 8+9). In this case, directly above the Rear Wheel Well.
NOTE – If you already have a Roof Rack installed, this can be a somewhat lengthy process. -
Attach Side Ladder: Loosely secure Side Ladder to Rail Nuts using (2) 3/8-16 x 0.5” Button Head Hex Screws and Lock Washers (FIG 10+11).
STEP | 04 SIDE LADDER ALIGNMENT
-
Position Side Ladder: Position Side Ladder in desired location (FIG 12).
NOTE- We like the ladder as close to the rear wheel well as we can in order to utilize the Support Bracket. -
Attach Mounting Brackets: Take the Mount Plate and the Support Bracket (if applicable) and loosely attach them to the bottom of the ladder using the 3/8-16 X 1” Screws, 3/8 Flat Washers, and 3/8-16 Nylock Nuts (FIG 13).
-
Drill for Support Bracket (if applicable): Locate where the support bracket lands on the chassis beam shown in FIG 14 and use it to mark the thru hole to be drilled. Once marked, swing the bracket out of the way so you can access with power drill. Drill through using a 1/2” Drill Bit.
NOTE – Leave this support bracket loose as you fit everything in place, or you’ll likely need to loosen it again.
NOTE – Make sure that the ladder is straight up and down.
TOOLS REQUIRED FOR THIS STEP
- + 7/32” ALLEN WRENCH
- + 9/16” WRENCH OR SOCKET
- + POWER DRILL
- + 1/2” DRILL BIT
STEP | 05 SIDE LADDER INSTALL
- Fastening Support Bracket to Van (if applicable): After drilling, swing the bracket back in place and loosely attach using (1) 3/8-16 x 1” Screw, 3/8 Flat Washer, and 3/8-16 Nylock Nut (FIG 15).
- Fastening Mount Plate to Van: Slide the Mount Plate up as tight to the pinch seam as you can (FIG 16) and temporarily tighten the two bolts holding it to the Ladder. Using the Mount Plate as a guide, drill pilot holes for the two center holes along the pinch seam, then drive 1/4” Self Drilling Screws through them to hold it in place. You’ll have to remove the ladder to get to the remaining two (2) as they sit behind the ladder uprights and are not easily accessible without a 90-degree drill head.
- Tighten Down All Fasteners: Go back and tighten down your fasteners along the Roof Rail and Mounting Brackets.
NOTE – If desired, you can replace the self drilling screw with 1/4-20 bolts & nuts.
TOOLS REQUIRED FOR THIS STEP
- + POWER DRILL
- + 1/8” DRILL BIT
- + 9/16” WRENCH OR SOCKET
- + 7/32” ALLEN WRENCH
- + 7/16” WRENCH OR SOCKET
- + 5/32” ALLEN WRENCH
GET OUT AND EXPLORE!
+ LEAVE US A REVIEW
Happy with your new FVC product? We would love to hear (and see) from you!
Head to the product page and click “Leave Review.” Add a short review and
upload a few photos to be showcased on the product page.
+ SHARE YOUR PICS
We love seeing how our customers use their FVC products and following along
with your adventures. Tag us in your photos with : @flatlinevanco or send them
to us via email. We love posting customer pictures in our feed!
+ NEED ANY HELP?
If you are having any issues with your product, please reach out, and we will
make it right. FVC is a company of van and outdoor enthusiasts that design and
use our own products, so we want you to be as stoked on your new parts as we
are!
FL ATLINE VAN CO • SUPPORT@FLATLINEVANCO.COM • 888-667-5576
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>