FVCO SP0208B Low Roof Sprinter Van Side Ladder Installation Guide

May 15, 2024
FVCO

**FVCO SP0208B Low Roof Sprinter Van Side Ladder Installation Guide

**

DIMENSION INSTRUCTION

All Flatline Van Co products must be properly assembled and secured before attaching to your
vehicle. Improper attachment could result in an automobile accident, and could cause serious bodily
injury or death to you or to others involved. You are responsible for assembling and securing flatline
van co products to your vehicle, checking the mounting points and attachments prior to use,  andregularly inspecting the products for wear and or damage. We always recommend you use a professional to install any aftermarket accessories to your vehicle. If you have no mechanical experience and are not thoroughly familiar with the installation procedures, you must have the product installed by a professional installer or other qualified persons. The responsibility is yours and must be taken seriously for everyone’s safety.

THANK YOU!

  • RE YOU EXCITED ABOUT YOUR NEW WHEEL WRAP SIDE LADDER? HERE ARE A FEW
    THINGS TO DO BEFORE BEGINNING THE INSTALLATION PROCESS–

  • PLEASE INSPECT THE PRODUCT TO ENSURE THERE WAS NO
    DAMAGE INCURRED DURING SHIPPING.

  • IF THERE IS DAMAGE TO REPORT, PLEASE CONTACT OUR
    CUSTOMER SERVICE DEPARTMENT AS SOON AS POSSIBLE.

  • NEXT, USING THE “PACKAGE CONTENTS” PAGE, CHECK INVENTORY AND FAMILIARIZE YOURSELF WITH THE PARTS AND HARDWARE.

  • GATHER ALL TOOLS REQUIRED FOR INSTALL.
    -9/16 BOX WRENCH OR SOCKET
    -7/32 HEX KEY ALLEN WRENCH
    -POWER DRILL
    -1/2“ DRILL BIT
    -1/8” DRILL BIT

  • HAVING A SECOND PERSON TO HELP OUT IS RECOMMENDED.

  • ESTIMATED INSTALL TIME – 30 MIN

TOOLS

9/16 WRENCH

7/32 ALLEN KEY

5/32 ALLEN KEY

PACKAGE CONTENTS

LADDER BOTTOM QTY – 1

LADDER TOP QTY –

MOUNT PLATE QTY – 1

SIDE LADDER COUPLER QTY – 2

LOWER SUPPORT BRACKET QTY – 1

HARDWARE PACK

3/8 SCREW BELLEVILLE
SPRING LOCK WASHER QTY – 2| 3/8-16 NYLON INSERT LOCKNUT QTY – 3| 3/8 SCREW FLAT WASHER QTY – 4
---|---|---
1/4 X 1 HEX HEAD WITH SEALING WASHER DRILLING SCREW QTY – 4| 3/8-16 X 0.75 BUTTON HEAD
HEX DRIVE SCREW QTY – 2| 3/8-16 X 1 BUTTON HEAD HEX DRIVE SCREW QTY – 3
1/4-20 X 0.75 BUTTON HEAD HEX DRIVE SCREW
QTY – 8| PRINTER RAIL NUT
QTY – 2|

LET’S GET STARTED!

  1. PLACE THE LADDER HALVES FRONT SIDE DOWN, INSERT THE COUPLERS
    INTO ONE HALF (SEE FIGURE 1), AND TIGHTEN DOWN USING THE 1/4-20 SCREWS.

  2. SLIDE THE OTHER LADDER HALF ONTO THE COUPLERS AND TIGHTEN DOWN.
    NOTE – IF DESIRED YOU CAN USE BLUE LOCTITE ON THE SCREWS.

  3. NEXT, SLIDE THE TWO (2) RAIL NUTS INTO THE ROOF RAIL ON YOUR VAN.
    NOTE- IF YOU’VE ALREADY INSTALLED A ROOF RACK, THIS MAY BE
    TIME CONSUMING.

RAIL NUT

  1.  NOW POSITION THE LADDER ON THE VAN, HANGING IT ON THE ROOF RAIL. LOOSELY SCREW THE TOP OF THE LADDER DOWN TO THE ROOF RAIL USING THE 3/8-16 X .75” SCREWS AND THE 3/8 BELLEVILLE LOCK WASHERS JUST ENOUGH THAT IT IS SNUG (SEE FIGURE 3)
    NOTE – WE LIKE TO PLACE THE LADDER AS CLOSE TO THE REAR WHEEL WELL AS WE CAN. SEE IMAGE BELOW
    MOUNT PLATE

SUPPORT BRACKET

  1. TAKE THE MOUNT PLATE AND THE SUPPORT BRACKET (SEE RIGHT) AND LOOSELY ATTACH THEM TO THE BOTTOM OF THE LADDER USING THE 3/8-16 X 1” SCREWS, 3/8 FLAT WASHERS, AND 3/8-16 NYLOCK NUTS.
    SEE REF PHOTO 1 & 2
    NOTE – MAKE SURE THAT THE LADDER IS STRAIGHT UP AND DOWN.

  2. LOCATE THE SUPPORT BRACKET ON THE CHASSIS BEAM SHOWN IN
    REF PHOTO 2 & 3 AND USE IT TO MARK THE THRU HOLE TO BE DRILLED. ONCE MARKED, SWING THE BRACKET OUT OF THE WAY SO YOU CAN ACCESS WITH
    POWER DRILL. AFTER DRILLING, SWING THE BRACKET BACK IN PLACE AND LOOSELY ATTACH USING THE REMAINING 3/8-16 X 1” SCREW, 3/8 FLAT WASHERS, AND 3/8-16 NYLOCK NUT.
    NOTE – LEAVE THIS SUPPORT BRACKET LOOSE AS YOU FIT EVERY THING IN PLACE, OR YOU’LL LIKELY NEED TO LOOSEN IT AGAIN.

  3. YOU’LL WANT TO SLIDE THE MOUNT PLATE UP AS TIGHT TO THE PINCH SEAM
    ON THE BOTTOM OF THE VAN AS YOU CAN, AND THEN TIGHTEN THE BOLTS.
    USING THE MOUNT PLATE AS A GUIDE, DRILL THE THREE CENTER HOLES
    THROUGH THE PINCH SEAM, THEN SCREW THE 1/4 SELF DRILLING SCREWS
    THROUGH THEM. YOU’LL HAVE TO REMOVE THE LADDER TO GET TO THE REMAINING TWO (2) AS THEY SIT BEHIND THE LADDER UPRIGHTS AND ARE
    NOT EASILY ACCESSIBLE WITHOUT A 90* DRILL HEAD. (SEE FIGURE 5)
    NOTE- IF DESIRED, YOU CAN REPLACE THE SELF DRILLING SCREWS WITH 1/4-20 BOLTS & NUTS.

**VIEW OF SUPPORT FROM INSIDE WHEEL WELL

**

  1. AFTER INSTALLING THE REMAINING TWO (2) 1/4 SELF DRILLING SCREWS, TIGHTEN DO

GET OUT AND EXPLORE!

LEAVE US A REVIEW

Happy with your new FVC product? We would love to hear (and see) from you! Head to the product page and click “Leave\ Review.” Add a short review and upload a few photos to be showcased on the product page.

SHARE YOUR PHOTOS WITH US

We love seeing how our customers use their FVC products and following along with your adventures. Tag us in your photos with @flatlinevanco or send them to us via email. We love posting customer pictures in our feed!

CUSTOMER SUPPORT

If you are having any issues with your product, please reach out, and we will make it right. FVC is a company of van and outdoor enthusiasts that design and use our own products, so we want you to be as stoked on your new parts as we are!

@flatlinevanco

facebook.com/flatlinevanco

youtube.com/c/flatlinevanco

support a flatlinevanco.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals