VOLLRATH T38727 Cafeteria Breath Guard Installation Guide
- August 8, 2024
- VOLLRATH
Table of Contents
VOLLRATH T38727 Cafeteria Breath Guard
Product Information
Specifications:
- Model: One Piece and Three Piece Cafeteria Breath Guard
- Item No.: 2350030-01 Rev 04/12
Product Usage Instructions
One Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figure 1. Repeat for all four uprights.
Three Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
FAQ:
-
Q: What should I do if I notice cracks in the plastic parts during installation?
A: If you notice cracks in the plastic parts during installation, stop tightening immediately to prevent further damage. Contact customer service for assistance in replacing the damaged parts. -
Q: Can I disassemble the breath guard for cleaning?
A: Yes, you can disassemble the breath guard for cleaning purposes. Follow the reverse steps of installation to disassemble the components and clean them thoroughly before reassembling.
Breath Guard Installation
These instructions cover the installation of the one pice Cafeteria Breath Guard and the three piece Cafeteria Breath Guard.
One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE: Use caution when tightening the cap nuts. Overtightening may cause
the plastic to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
Three Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE: Use caution when tightening the cap nuts. Overtightening may cause
the plastic to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201
U.S.A.
Main Tel: 800.628.0830
Service Tel: 800.628.0832
FAX: 800.752.5620
Vollrath of Canada, Co.
Tel: 800.695.8560
FAX: 800.752.5620
© 2010 The Vollrath Company, L.L.C.
www.vollrathco.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>