ZEBRA ZD510, ZD511 Wristband Printing Solution User Guide
- August 8, 2024
- ZEBRA
Table of Contents
- ZEBRA ZD510, ZD511 Wristband Printing Solution User Guide
- Worldwide
- Regulatory Information
- End User License Agreement
- Warranty
- Antenna Information:
- WLAN specifications:
- 802.11 b
- 802.11 g
- 802.11 n
- 802.11 a/n
- GHz
- United States of America
- FCC Compliance
- IMPORTANT
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZEBRA ZD510, ZD511 Wristband Printing Solution User Guide
Worldwide
Regulatory Information
All Zebra devices are designed to be compliant with the rules and regulations
in locations they are sold and will be labeled as required. For more
information about Zebra’s compliance with national and international mandates,
go to: www.zebra.com/compliance
For the latest version of this guide, go to:
www.zebra.com/support
Any changes or modifications to Zebra equipment, not expressly approved by
Zebra, could void the user’s authority to operate the equipment.
End User License Agreement
For the complete End User License Agreement, go to www.zebra.com/eula
Warranty
For the complete hardware product warranty statement, go to
www.zebra.com/warranty
Do not dispose of this product in unsorted municipal waste. This product is
recyclable, andshould be recycled according to your local standards. For more
information, please see our website at:
Antenna Information:
- Type = Patch
- Gain = 66dBi @ 2.4GHz
- Gain = 19dBi @ 5GHz
- Type = Chip
- Gain = 1dBi @ 4 GHz
WLAN specifications:
802.11 b
- 4 GHz
- DSSS (DBPSK, DQPSK and CCK)
- RF power 77 dBm (EIRP)
802.11 g
- 4 GHz
- OFDM (16-QAM and 64-QAM with BPSK and QPSK)
- RF power 61 dBm (EIRP)
802.11 n
- 4 GHz
- OFDM (16-QAM and 64-QAM with BPSK and QPSK)
- RF power 62 dBm (EIRP)
802.11 a/n
- 15-5.25 GHz, 5.25-5.35 GHz, 5.47-5.725
GHz
- OFDM (16-QAM and 64-QAM with BPSK and QPSK)
- RF power 89 dBm (EIRP)
United States of America
FCC Compliance
This device complies with Part 15 rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired
This equipment has been tested and found to comply with the limits for Class B Digital Devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter- ference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the product manuals, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi- sion reception, the user is encouraged to do one or more of the following measures:
- Reorient or relocate the receiving
- Increase the separation between the equipment and
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
- Consult the dealer or an experienced RF service technician for
IMPORTANT
- The radio must be installed with a minimum 20 cm separation between the user and the
- The radio must not be co-located or used in simultaneous transmitting condition with another
- The host system shall have a label to indicate that the system contains a certified
- An example is “Contains FCC ID : XXXXX-XXXXXXXX , IC ID: XXXXX-XXXXXXXX”.
- The radio is for indoor use only in the 5150-5250 GHz frequency
The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with fully shielded communication cables.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>