neptronic STS3 Series Wall Thermostat Instruction Manual
- August 6, 2024
- neptronic
Table of Contents
neptronic STS3 Series Wall Thermostat
Specifications
- Models: STS3-11C(10 K), STS3-11F(10 K), STS3-13C(3.3 K), STS3-13F(3.3 K)
- Features : Wall Thermostat
Technical Data
- Scale: Celsius/Fahrenheit
- Setpoint Range: 10 K (STS3-11C, STS3-11F), 3.3 K (STS3-13C, STS3-13F)
- Sensor: NTC
- Electrical Connection: 2 wires 0.8 mm2 [18 AWG] minimum
- Operating Temperature: TBD
- Storage Temperature: TBD
- Relative Humidity: TBD
- Ingress Protection: IP 30 (EN 60529)
- Weight: 68 g. [0.15 lb]
- Dimensions: A = 3.00 | 78mm, B = 3.00 | 78mm, C = 1.00 | 24mm, D = 2.36 | 60mm
Product Usage Instructions
Mounting Instructions
CAUTION: Remove power to avoid a risk of malfunction.
- Remove the captive screw holding the base and front cover of the room setpoint sensor enclosure.
- Lift the front cover to separate it from the base.
- Pull wire through the hole in the base.
- Secure the base to the wall using wall anchors and screws provided. Make appropriate connections.
- Mount the control module on the base and secure using the screw.
Recycling Instructions:
Please return the product to your Neptronic local distributor for recycling
at the end of its life cycle. Visit
www.neptronic.com to find the nearest authorized
distributor.
FAQ :
-
Q: What should I do if the thermostat malfunctions?
A: If you encounter any issues with the thermostat, first ensure that power is disconnected. Then refer to the user manual for troubleshooting steps or contact Neptronic customer support for assistance. -
Q: Can I use this thermostat with other heating devices?
A: Yes, this thermostat can be used with a DF series duct heaters, BM023C actuator, and other Neptronic controllers as mentioned in the specification
Wall Thermostat
Specification and Installation Instructions
Models
STS3-11C(10 KΩ) STS3-11F(10 KΩ) STS3-13C(3.3 KΩ) STS3-13F(3.3 KΩ)
Features
- Selectable Celsius or Fahrenheit scale
- Sensor 3.3 KΩ or 10 KΩ
Technical Data
Specification | STS3-11C | STS3-11F | STS3-13C | STS3-13F |
---|---|---|---|---|
Description | Can be used with a DF series duct heaters, BM023C actuator, and |
other Neptronic controllers.
Scale| Celsius| Fahrenheit| Celsius| Fahrenheit
Setpoint Range| 14°C to 30°C| 57°F to 86°F| 14°C to 30°C| 57°F to 86°F
Sensor NTC| 10 KΩ| 3.3 KΩ
Electrical Connection| 2 wires 0.8 mm2 [18 AWG] minimum
Operating Temperature| 2°C to 35°C (35°F to 95°F)
Storage Temperature| 0°C to 50°C (32°F to 122°F)
Relative Humidity| 5 to 95 % non condensing
Ingress Protection| IP 30 (EN 60529)
Weight| 68 g. [0.15 lb]
Dimensions
A = 3.00” | 78mm
B = 3.00” | 78mm
C = 1.00” | 24mm
D = 2.36” | 60mm
| ****
Wiring
(Factory Settings)
Mounting Instructions
CAUTION : Remove power to avoid a risk of malfunction.
- A. Remove the captive screw that’s holding the base and the front cover of the room setpoint sensor enclosure.
- B. Lift the front cover of the enclosure to separate it from the base.
- C. Pull wire through the hole in the base.
- D. Secure the base to the wall using wall anchors and screws (supplied). Make the appropriate connections.
- E Mount the control module on the base and secure using the screw.
Recycling at end of life: please return this product to your Neptronic local distributor for recycling. If you need to find the nearest Neptronic authorized distributor, please consult www.neptronic.com.