neptronic TBT3065A TT065 Actuator Instruction Manual
- June 3, 2024
- neptronic
Table of Contents
**neptronic TBT3065A TT065 Actuator Instruction Manual
**
Feature
- Clutch for manual adjustments.
- Maintenance free.
- Position indicator.
- Fail safe by Enerdrive System1 (on model 060 & 080).
- Auxiliary switches (on model 020 & 080)
Old Number|
---|---
TBT3000A| TT000
TBT3005A| TT005
TBT3021A| TT020
TBT3060A| TT060
TBT3065A| TT065
TBT3080A| TT080
RBT5000A| RT000
RBT5005A| RT005
RBT5021A| RT020
RBT5060A| RT060
RBT5065A| RT065
RBT5080A| RT080
Technical Data
Technical Data| TT000| TT005| TT020| TT060| TT065|
TT080| RT000| RT005| RT020| RT060| RT065|
RT080
---|---|---|---|---|---|---|---|---|---|---|---|---
TBT 3000A| TBT 3005A| TBT 3021A| TBT 3060A|
TBT 3065A| TBT 3080A| RBT 5000A| RBT 5005A|
RBT 5021A| RBT 5060A| RBT 5065A| RBT 5080A
Auxiliary switches| No| No| Yes(2)| No| No| Yes (2)| No| No| Yes(2)| No|
No| Yes (2)
Feedback| No| Yes| No| No| Yes| No| No| Yes| No| No| Yes| No
Fail safe – Enerdrive| No| Yes| No| Yes
Power consumption| 8 VA| 24 VA Peak, 8 VA| 10 VA| 24 VA Peak, 10 VA
Control signal| 3 wire / 2 position,
3 wire / 3 point floating
| 2 wire / 2 position,
4 wire / 3 point floating
| 3 wire / 2 position,
3 wire / 3 point floating
| 2 wire / 2 position,
4 wire / 3 point floating
Weight| 4.5 lbs. [2 kg]| 7 lbs. [3.2 kg]
Torque| 180 in.lb. [20 Nm] at rated voltage| 360 in.lb. [40 Nm] at rated
voltage
Running time through 90º| 60 to 85 sec Torque dependant
Power supply| 22 to 26 VAC or 28 to 32 VDC
Electrical connection| 18 AWG [0.8 mm2] minimum
Inlet bushing| 2 inlet bushing of 7/8 in [22.2 mm]
Angle of rotation| 0 to 90 degrees, mechanically adjustable with SLD
(optional), (factory set with 90º stroke)
Direction of rotation| Reversible, Clockwise (CW) or Counterclockwise
(CCW) (factory set with CW direction)
Ambient temperature| 0ºF to +122ºF [-18º C to +50º C]
Storage temperature| -22ºF to +122ºF [-30º C to +50º C]
Relative Humidity| 5 to 95 % non condensing.
Warning: Do not press the clutch when actuator is powered
Dimensions
| Dimension | Inches | Metric (mm) |
|---|---|---|
| A | 5.20 | 132.1 |
| B | 1.33 | 33.8 |
| C | 9.13 | 231.9 |
| D | 3.55 | 90.2 |
Caution
We strongly recommend that all neptronic® products be wired to a separate transformer and that transformer shall service only neptronic® products. This precaution will prevent interference with, and/or possible damage to incompatible equipment. When multiple actuators are wired on a single transformer, polarity must be observed. Long wiring runs create voltage drop which may affect the actuator performance.
Mechanical installation
- Manually close the damper blades and positioned the actuator at 0º or 90º.
- Slide the actuator onto the
- Tighten the nuts on the “U” bolt to the shaft with a 10mm wrench to a torque of 150 lb. [17 Nm].
- Slide the mounting bracket under the actuator. Ensure free movement of the slot at the base of the The bracket pin must be placed in the mid distance of the slot.
- Fix the bracket to the ductwork with #8 self-tapping
Wiring Diagrams
Models TT000, 005 & 020 **RT000, 005 & 020| Models TT060, 065 & 080
**RT060, 065 & 080
---|---
3 wire / 2 position (ON-OFF)
| 2 wire / 2 position (ON-OFF)
3 wire / 3 point floating
| 4 wire / 3 point floating
PC Board
Dip switch settings
Stroke Adjustment
To adjust the stroke, use the stroke limiting device (SLD). (not included)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>