GamerZnationTech Ultra Catcher 4 User Manual

GamerZnationTech Ultra Catcher 4

Product Specifications

• Product Name: Ultra Catcher 4
• Functionality: Bluetooth ID clearing, Vibration control, Charging indicator
• Power Source: Rechargeable battery
• Charging Method: USB

Product Usage Instructions

Switching Functions
To switch functions:
Short press the button for basic function switching.

Bluetooth ID Clearing
To clear Bluetooth Pairing ID:

• Long press the button for 3 seconds.
• Green and Red lights will flash indicating the clearing process.
• Clear successful: Green Light flashes 3 times.
• Clear failed: Red Light flashes 3 times. (Please re-operate if needed)

Vibration Control
To control vibration:

• Long press the button for 3 seconds.
• Vibration on: Green Light flashes 3 times.
• Vibration off: Red Light flashes 3 times.

Pairing Connection
To pair with a device:

1. Turn on Bluetooth on your mobile device.
2. Access Main Menu > Settings.
3. Select ‘Pokemon Go Plus’ in the settings page.
4. Pocket Auto Catch Lightning will start to pair automatically.
   • Unpaired ID: Green Light flashes
   • Paired ID: Blue Light flashes

Charging Instructions
To charge your device:

• Connect the device to a USB charge port using the provided cable.
• LED will show 3 colors repeating during charging.
• When fully charged, LED will show a white light.

FAQ

Q: What should I do if I can’t charge the device smoothly?
A: If the rechargeable battery enters protection mode due to long-term non- usage, activate it by pressing and holding the button, then plugging and unplugging the USB several times until the white LED flashes, and then release the button.

ULTRA CATCHER 4 MANUAL

A1

• How to switch the function
  Short press the button to switch function.

• Blue Light
  Clear Bluetooth Pairing ID

• Green Light
  Vibration on / off

Reset to factory settings:

1. Hold button
2. insert into the charge cable and connect to a USB charge port.

A2

• Function Description
• Function Introduction
  • Blue Light: Clear Bluetooth Pairing ID
• Long press the button for 3 seconds
• Execute clearing ID
• Green and Red flashing (Please wait 11-20 seconds when clearing ID)
• Clear successful:
  • Green Light flashes 3 times
• Clear failed:
  • Red Light flashes 3 times
• Clear Failed (Please re-operate)

A3

• Green Light: Vibration on / off Long press the button for 3 seconds
• Vibration on:
• Green Light flashes 3 times
• Vibration off:
• Red Light flashes 3 times

A4
Pairing Connection

1. Turn on Bluetooth in your mobile.

2. Tap the Main Menu.

3. Tap Settings.

4. Select Pokemon Go Plus in setting page. Pocket Auto Catch Lightning will start to pair automatically.
   Unpaired ID Green Light flashes
   Paired ID Blue Light flashes
   A5
   Pokemon Go Plus

5. Waiting for pairing. When the Pokemon Go Plus icon turns on, it means pairing is successful.

Not connected
Successful connection
Connected to Pokemon Go Plus

A6-A7
Others
Power / Connection / Other status

• 0 ~3 minutes: Vibrate for 2 times for every 10 seconds.
• 3 ~ 10 minutes: Vibrate for 2 times for every 30 seconds.
• Stop warning after 10 minutes.
• If the situation is “Intermittent “, it vibrate 3 times instead 2.

Out of internet| Fntermittent
Items are full| White|

• Vibrate for 2 times for every 2 seconds.
• Stop after 3 cycles.

Out of Pokeball| Flashing 3 times
Pokemon up to maximum / Far away from Pokestop| Permanently on

When you are playing Pokemon Go, there will be no vibration.

A8
Charge your Catch

• When charging, Pocket Auto Catch Lightning shows 3 colors repeat LED light.
• When the power is full, Pocket Auto Catch Lightning shows white LED light.

A9
Can’t charge smoothly?
When it is not used for a long time, the rechargeable battery may enters the protection mode and cannot be charged smoothly, you can activate the rechargeable battery by pressing and holding the button, then plugging and unplugging the USB several times until the white LED flashes, and then releasing the button.

FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>