msi D3050 Motherboard User Guide
- August 5, 2024
- MSI
Table of Contents
msi D3050 Motherboard
Product Overview
CPU
- 1 x AMD® Ryzen™ 7000 Series Processor
- Up to 16 cores, TDP up to 170W
Front Panel Connector
| 1| PWR_LED+| 2| FP_PWR
---|---|---|---|---
3| No pin| 4| SYS_ID_LED+
5| PWR_LED-| 6| SYS_ID_LED-
7| HDD_ACT_LED+| 8| SYS_FAULT_LED1-
9| HDD_ACT_LED-| 10| SYS_FAULT_LED2-
11| PWR_BTN| 12| NIC#1_ACT_LED+
13| PWR_BTN_GND| 14| NIC#1_ACT_LED-
15| RST_BTN| 16| SMB_SDA
17| RST_BTN_GND| 18| SMB_SCL
19| SYS_ID_BTN| 20| CHASSIS_INTRUSION
21| WIRE_TEMP_SENSOR| 22| NIC#2_ACT_LED+
23| NMI_BTN| 24| NIC#2_ACT_LED-
CPU and Cooler Installation
Connectors, Jumpers and LED Indicators
| Name | Description |
|---|---|
| JATX12V1 | 12-pin ATX power connector |
| ATX4PIN1 | 4-pin ATX power connector (Black) |
| SATAPWR1 | 4-pin SATA power connector (White) |
| JSDOMPWR1 | 2-pin SATA DOM power connector |
| SATA1~4 | SATA 3.0 6Gb/s ports |
| SATA5_6 | SATA 2.0 3Gb/s ports |
| M2_1~2 | M.2 slots (M Key, PCIe 4.0, 22110/ 2280) |
| FAN1~8, PUMP1 | Fan power connectors |
| JFP1 | Front panel connector |
| JTPM1 | SPI TPM module box header |
| JGPIO1 | GPIO header |
| JPMBUS1 | PMBus box header |
| JCHASSIS1 | Chassis intrusion header |
| JIPMB1 | IPMB box header |
| FP_I2C_1, RBP_I2C_1~2 | I2C box headers |
| JCOM1 | COM port box header |
| JUSB1 | USB 3.2 port box header |
| JUSB2 | USB 3.2 Gen 1 Type-A connector (USB 3.2 Gen 1/ USB 2.0) |
| MLAN_USB1 | GbE RJ45 port (for mgmt.)(upper, on rear side) |
USB 3.2 Gen 1/ USB 2.0 Type-A connectors (lower, on rear side)
JLANCONN1~2| GbE RJ45 ports (on rear side)
PCIE_1| PCIe 5.0 x 16 slot (Gen 5 x 16 signal from CPU)
PCIE_2| PCIe 4.0 x 8 slot (Gen 4 x 4 signal from CPU)
BMC_LED1| BMC Heartbeat LED
LED_H1, LED_L1| Port 80 Debug LEDs
COM1| COM port (on rear side)
JVGA1| VGA display connector (on rear side)
HDMI1| HDMI™ connector (on rear side)
JRTC_CLR1| CMOS clear (default pin 1-2 normal)
JSEL_M2| M2_2 / PCIE_2 selection (default set to pin 1-2, M2_2 enabled)
| Name | Description |
|---|---|
| JSEL_BMC1 | BMC selection (default pin 1-2, Using CPU) |
Memory
The server board offers compatibility with DDR5 ECC/ non-ECC UDIMMs,
supporting memory speeds up to 5200MT/s (2DPC).
Recommended Memory Population
Important
- Only support UDIMM.
- There should be at least 1 DDR5 DIMM populated.
- Paired memory installation for Max performance.
- If only 1 DIMM is populated in a channel, then populate it in the DIMMA2 slot.
- Populate the same DIMM type in each channel, specifically: 1. Use the same DIMM size; 2. Use the same number of ranks per DIMM.
- We don’t suggest other memory installation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>