CAMBRIA Designer Series Premium 3 Foot Custom Curtain Rod Installation Guide
- August 4, 2024
- CAMBRIA
Table of Contents
CAMBRIA Designer Series Premium 3 Foot Custom Curtain Rod
Product Specifications
- Model: Designer Series
- Compatible Rod Lengths: 3′, 3′ 6″, 4′, 4′ 6″, and 5′
- Rod Diameter: 1 1/8 inches
Product Usage Instructions
Tools Needed (Not Included)
- Tape Measure
- Pencil
- Drill
- 1/8″ Drill Bit
-
2 Phillips-head Screwdriver
- Level
Installation Instructions
- Determine the placement of the rod on the wall by referencing the Installation Diagram.
- Measure and mark the bracket locations above the window frame ensuring level placement.
- Mark the three mounting holes for each bracket on the wall using Wall Mount (Part-B) as a template.
- Drill three 1/8″ diameter pilot holes in the wall for all marked bracket locations.
- For drywall installation, screw plastic wall anchors (Part-G) into pilot holes until flush.
- For wall stud installation, skip using plastic wall anchors.
- Attach both Wall Mounts (Part-B) with the mounting stub pointing away from the wall.
PARTS LIST
INSTALLATION
- Determine the placement of the rod on the wall. Reference the Installation Diagram on the reverse side.
- Measure and mark the bracket locations above the window frame. Use a level to ensure the rod will be level on the wall.
- Mark the three mounting holes for each bracket on the wall using the Wall Mount (Part-B) as a template.
- Drill three 1/8” diameter pilot holes in the wall for all marked bracket locations.
- For drywall (hollow wall) installation: Screw plastic wall anchors (Part-G) into pilot hole until flush. Do not over tighten.
- For wall stud installation: The plastic wall anchors (Part-G) are not used.
- Attach both Wall Mounts (Part-B) with the mounting stub pointing away from the wall (Fig. 1). Hand tighten all mounting screws (Part-F) using a screwdriver to prevent screw head damage.
- Place Wall Bracket (Part-C) over the Wall Mount (Part-B) and tighten the rear set screw (Part-H) using the allen wrench (Part-I) provided (Fig. 2).
- Insert the Rod Bracket (Part-D) into the Wall Bracket (Part-C) and set the desired distance from the wall. Tighten the forward set screw (Part-H) with the allen wrench (Part-I) provided to lock the Rod Bracket (Part-D) in place.
- Install draperies or clip rings on the rod (Part-A) and place the rod in both brackets mounted on the wall (Fig. 3).
- Center the rod (Part-A) in the wall brackets and tighten the set screw (Part-E) with a screwdriver in each of the Rod Brackets (Part-D).
- Attach the end caps (Part-J) to each end of the rod (Part-A) and tighten the set screw (Part-H) with the allen wrench (Part-I) included as shown in Fig. 3.
- We want to Thank You for your purchase. Please enjoy your new window.
Parts exceeding the quantity listed may be included in the hardware kit. These extra parts can be discarded after assembly.
Replacement parts available. Email parts@cambriadesigner.com
TOOLS NEEDED
NOT INCLUDED
INSTALLATION DIAGRAM
modeforhome
Scan QR Code for additional information
Frequently Asked Questions
- Q: Are all necessary parts included in the package?
- A: Parts exceeding the listed quantity may be included. Any extra parts can be discarded after assembly.
- Q: How do I determine the drapery rod width needed?
- A: Measure the overall window width on both sides of the frame and add twice the panel’s width for stacking. The minimum width needed is A + B + B.
- Q: Can I get replacement parts if needed?
- A: Yes, replacement parts are available. Please email parts@cambriadesigner.com for assistance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>