PHOTONTEK 30W UV 30 Watt UV Supplemental LED Grow Light Bar Instruction Manual
- August 2, 2024
- PHOTONTEK
Table of Contents
PHOTONTEK 30W UV 30 Watt UV Supplemental LED Grow Light Bar
Specifications
- Product Name: 30W UV supplemental LED Light Bar
- Manufacturer: PhotonTek Horticultural Lighting
- Product Code: PTEKLED027
- EAN: 5060560030119
- Plug Type: N/A
Product Information and Specifications
INTRODUCTION
Thank you for purchasing the Photontek 30W UV supplemental LED Light Bar. This
manual describes how to install and use the light bar; please read this manual
thoroughly before attempting to install or operate any Photontek system. If
you are not comfortable with the installation of high-performance lighting
systems, you should seek the services of a qualified installation
professional.
PRODUCT DESCRIPTION
The Photontek 30W UV supplemental LED Light Bar has been specifically designed
to augment Photontek X / XT series full-spectrum LED grow light systems during
the plant’s flowering growth stage. Designed to fit directly on the Photontek
X / XT LED fixtures, this unit has an integrated driver and can also be
connected together in series with UV Bar Daisy Chain cable. Recent research
shows strategic exposure of indoor-grown plants to UVA & UVB light can
increase secondary metabolite and essential oil production as well as
inhibiting mold, mildew & pest infestation, minimizing the need for chemical
intervention. The 30W UV bar was specially designed to provide the ideal UV-B
[280-315 nm] and UV-A [315-400 nm] radiation doses to your plants based on
scientific support. A single fixture can provide 2.2 kJ/day (12 hours) of UV-B
energy and 518 kJ/day (12 hours) of UV-A output. This translates to a fixture
output of 100 mW of UV-B and 12000 mW UVA. Photontek ensures that this fixture
does not produce UV-C radiation. The UV Bar Daisy Chain cable will allow you
to easily connect several fixtures together in series. To ensure unit
performance, this LED bar has a single input and output socket for the UV
Power Cable or UV Bar Daisy Chain cable, depending on the use of that bar. For
this reason, the UV Power 120V/240V (13 ft) and Daisy Chain (5 ft) cables are
sold separately.
General Product Information
The Photontek 30W UV supplemental LED Light Bar is designed to provide
additional UV-A and UV-B light to enhance plant growth.
Technical Specifications
- UV-A (315-400NM): 12000 MW
- UV-B (280-315NM): 100 MW
- Input Voltage: 120-277 V AC, 50-60 Hz
- Input Power: 30 W, integrated 30 W (+/- 5%)
- Footprint: 4 ft X 2 ft
- Waterproof/Dustproof: IP65
- Life Span: L90 > 8500 HRS
- Weight: 2.7 Lbs
- Thermal Management: Non-condensing
- Power Factor: N/A
- Max Ambient Temperature: N/A
- Working Temperature: N/A
- Working Humidity: N/A
- Dimmable: No
- Daisy Chain Capability: Yes (Max 30 pcs)
Spectral Quantum Distribution Graph
The 30W UV bar has been developed for use with Photontek X / XT full
spectrum LED fixtures. It is recommended to use two UV bars to supplement each
fixture.
Light distribution curve
Environment
The LED fixture is intended to be used in climate-controlled grow rooms and
indoor farms. The product may be used in damp environments but may not be used
in wet environments or outdoors. The product will operate in ambient
temperatures from -50°F (-10°C) to 104°F (40°C) but will function at optimal
level between 68°F (20°C) to 86°F (30°C). The product will operate in 20% –
90% humidity, non-condensing.
Legal
This product is FCC, IC, CSA & CE certified compliant with LVD and EMC
directive test standards.
SAFETY RECOMMENDATIONS AND WARNINGS
WARNING!
Carefully read the warnings below before using or working with the product!
The Photontek 30W UV Supplemental LED light Bar produces UVB (near UV Erythemal) and UVA (near UV-black light) electromagnetic radiation with wavelengths from 280 to 400 nm. To avoid any biological affects in physical human body, please switch the power off when installing and/or during the maintenance processes on your grow system. If turning OFF UV Bars won’t be possible, all exposed skin should be covered with opaque material including face, neck, head, hands, and arms. It is assumed that other body parts are covered if wearing proper laboratory attire; long pants, closed toe shoes, gloves, long sleeve lab coats and protective glasses. Do not look directly at the light as the UVB radiation from the light fixture can damage eyes and skin. Do not restrict the airflow across the fixtures to avoid any heat build- up which may reduce drastically the lifetime of your UV supplemental LED bars. Do not put the UV Supplemental LED Bar in contact with any surface while still ON. Only use on plants.
CAUTION! Ultraviolet Radiation (UV)
- Do not look directly into the UV light during operation
- Wear protective eyewear to avoid exposure to UV light
- Avoid direct skin & eye exposure to UV light
- Keep out of reach of children
- Do not open or disassemble the LED fixture as it contains no serviceable parts inside. Opening or modifying the LED fixture can be dangerous and will void the warranty.
- Do not use the LED fixture when either the LED fixture or its power cable are damaged. Replace the power cable with correctly rated cable only.
- Modifications to the cables can lead to unwanted electromagnetic effects which may make the product not comply with legal requirements.
- Do not expose the LED fixture to:
Condensing humidity, heavy mist or direct spray;
Ambient temperatures outside the specified range; Dust and contamination;
Direct sunlight during use or HID light that may heat up the driver.
- Always disconnect the LED fixture from mains before performing any maintenance.
- Always allow for a cool down period of at least 20-30 minutes before touching the LED fixture. Touching the LED fixture when the fixture is lit or immediately after may result in burns!
- Natural convection removes heat away from the heatsink. In order for the system too properly cool itself, at least 2´´ of space is required between the fixture and the roof of your grow area.
- Do not use abrasive materials or aggressive cleaning agents to clean the LED fixture as this may damage the secondary optics. Instead use a clean damp or dry fabric/cloth.
- Do not use the LED fixture near flammable, explosive or reactive substances. The LED fixture can reach temperatures of 104°F.
- Do not use sulphur vaporizers or water misters.
- The installation and use of the LED fixture is the responsibility of the end user. Incorrect use or installation can lead to failure and damage to the LED fixture. Damage to the LED fixture and electronic circuitry as a result of incorrect installation and use revokes the warranty.
CONTENTS INSTALLATION
WARNING!
-
Mounting and installing the LED fixture must be in accordance with the applicable local laws and regulations.
-
The installer is responsible for correct and safe installation.
-
Ensure the local cabling can support the voltage and current requirements of the LED fixture.
-
Avoid coiled cables and keep mains leads separated to help prevent electromagnetic interference.
-
Do not connect or disconnect the LED fixture under load.
Fixture assembly & installation
WARNING!
The light bar is shipped with a protective plastic cover over the diodes.
Please ensure this protective cover is removed before use!
Recommended Coverage
The Photontek 30W UV Supplemental LED Bar was designed to fit directly into
the X / XT fixtures.
To make sure you achieve the best light spread over the canopy, we recommend:
- Integrate a minimum of 2 units of 30W UV Supplemental Light LED Bar, with:
- X 465W PRO – 4 x 4 ft footprint
- X 600W PRO – 5 x 5 ft footprint
- XT 1000W CO2 – 5 x 5 ft footprint w/ CO2 Supplement Integrate a minimum 3 units of 30W UV Supplemental Light LED Bar, with:
- X 1000W PRO – 6.5 x 5 ft footprint
Recommended UV-B + UV-A Radiation Application
- Always mix the supplemental UVB + UVA radiation with the Photontek X / XT Full Spectrum LED Range.
- The UV bars have been designed for 12 hours operation to match the flowering photoperiod and can be switched ON/OFF at the same time as the X / XT full-spectrum fixture.
- UV strategic exposure to flowering plants can begin from 4 weeks before harvest and particularly the last 2-3 weeks of bloom when flower and resin development is most present.
- For a good UV radiation spread, ensure to install the recommended minimum units and follow the distance to canopy referred on the Grow Light Strategies table, download from: https://photontek-lighting.com/education/
- If you notice plant damage, we recommend to increase the distance between fixture and canopy or decrease the UV light output delivered to your plants by reducing the UV photoperiodic time…
Connecting the UV bar to the mains power
WARNING!
- Make sure mains power is switched off.
- Ensure the power supply cable is not coiled and does not touch any hot surfaces.
- Connect the cables according to local rules, safety regulations and electrical code.
- Do not connect or disconnect the LED fixture under load.
- The Photontek UV LED bar power cable (13 ft) and the UV LED bar daisy chain cable (5 ft) are both sold separately.
- The power cable should be connected to the UV bar power input port;
- Remove dust cap from UV bar Input connector.
- Correctly align connectors and push together until ‘click-locked’.
- Connect mains power plug to switching gear/power supply.
- Switch on mains power.
- To disconnect;
- Switch OFF mains power turn power cable connector twist-lock anti-clockwise and pull apart from bar connector port.
Connecting UV bars together in series with daisy chain cables
- A UV bar power cable is required to power the first UV bar and then further UV bars can be connected in series from the first bar
- and powered with the UV daisy chain cables.
- Maximum 30pcs UV bar can be daisy-chained from one power source.
- Ensure mains power is OFF
- Using the Photontek UV daisy chain cable; connect UV bar [1] power output port to UV bar [2] power input port by correctly
- aligning connectors and push together until ‘click-locked’.
- Continue until all UV bars are connected.
- Switch on mains power.
- To disconnect;
- Switch OFF mains power
- Turn daisy chain cable connector twist-lock anti-clockwise and pull apart from bar connector port.
- Do not connect or disconnect the UV bars under load.
INSPECTION, MAINTENANCE AND REPAIR
WARNING!
- Disconnect the LED fixture from mains before performing any maintenance or repairs.
- WARNING! Do not open or disassemble the LED fixture, it contains no serviceable parts inside. Opening the LED fixture can be dangerous and will void the warranty.
- WARNING! Do not connect or disconnect the LED fixture under load
- WARNING! Always wait 20 – 30 minutes for the LED light bars to cool down.
- CAUTION! Do not clean the LED fixture with detergents, abrasives or other aggressive substances.
- Regularly check the LED fixture for dust or dirt build up. Clean if necessary. Contamination may cause overheating and decreased performance.
- Clean the outside of the LED fixture using a dry or damp cloth.
- Regularly check the cords of the LED fixture to ensure it is undamaged.
STORAGE AND DISPOSAL
Store the LED fixture in a dry and clean environment, with an ambient
temperature of -77°F to 131°F. The product must not be discarded as unsorted
municipal waste but must be collected separately for the purpose of treatment,
recovery and environmentally sound disposal..
WARRANTY
Photontek warrants the mechanical and electronic components of their product
to be free of defects in material and workmanship if used under normal
operating conditions for a period of one (1) year from the original date of
purchase. If the product shows any defects within this period and that defect
is not due to user error or improper use Photontek shall, at its discretion,
either replace or repair the product using suitable new or reconditioned
products or parts. In case Photontek decides to replace the entire product,
this limited warranty shall apply to the replacement product for the remaining
initial warranty period, i.e. one (1) year
info@photontek-lighting.com
www.photontek-lighting.com
FAQ
Q: Can I connect multiple UV bars together?
A: Yes, you can connect multiple UV bars together in series using daisy chain
cables. The maximum number of UV bars that can be connected in this way is 30.
Q: What is the recommended coverage for the 30W UV supplemental LED Light
Bar?
A: The recommended coverage for the light bar is a 4 ft x 2 ft area.
References
- Sustainable LED lighting solutions | Philips lighting
- PHOTONTEK Lighting | LED lighting | LED grow lights | LED Fixtures
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>