PhotonTek PTEKLED018 X 600W Pro LED Grow Light Owner’s Manual
- June 12, 2024
- PHOTONTEK
Table of Contents
PhotonTek PTEKLED018 X 600W Pro LED Grow Light
INTRODUCTION
Thank you for purchasing the PhotonTek X 600W Pro linear multi-light bar LED
fixture. This manual describes how to install and use the PhotonTek fixture;
please read this manual thoroughly before attempting to install or operate any
PhotonTek X Series system
PRODUCT DESCRIPTION
The PhotonTek X 600W Pro LED is an electronic horticultural LED fixture using
a linear array design with six LED light bars. The PhotonTek X 600W Pro is a
highly efficient high-intensity full-cycle grow lighting solution for
commercial horticulture cultivation. The PhotonTek X 600W Pro has the power
and flexibility to scale from vegetative growth to higher light intensities in
bloom.
In this manual, the Photontek X 600W Pro LED will be referred to as: “the LED
fixture”.
PRODUCT INFORMATION AND SPECIFICATIONS
General Product Information
Technical Specifications
Spectra
Light distribution curve
Environment
The LED fixture is intended to be used in climate-controlled grow rooms and
indoor farms. The product may be used in damp environments but may not be used
in wet environments or outdoors.
The product will operate in ambient temperatures from -20° c to 40°C but will
function at optimal level between 20° c to 30°C. The product will operate in
20% – 90% humidity, non-condensing.
Legal
This product is FCC, IC, CSA & CE certified compliant with LVD and EMC
directive test standards.
SAFETY RECOMMENDATIONS AND WARNINGS
Carefully read the warnings below before using or working with the product!
-
Always adhere to the local rules and regulations when installing or using the LED fixture.
-
Do not open or disassemble the LED fixture as it contains no serviceable parts inside. Opening or modifying the LED fixture can be dangerous and will void the warranty.
-
Do not use the LED fixture when either the LED fixture or its power cord are damaged. Replace the power cord with correctly rated cord only.
-
Modifications to the cabling can lead to unwanted electromagnetic effects which may make the product not comply with legal requirements.
-
Do not expose the LED fixture to:
Condensing humidity, heavy mist or direct spray;
Ambient temperatures outside the specified range;
Dust and contamination;
Direct sunlight during use or HID light that may heat up the driver. -
Always disconnect the LED fixture from mains before performing any maintenance.
-
Always allow for a cool down period of at least 20-30 minutes before touching the LED light bars. Touching the LED bars when the fixture is lit or immediately after may result in burns!
-
Natural convection removes heat away from the heatsink. In order for the system too properly cool itself, at least 5cm of space is required between the fixture and the roof of your grow area.
-
Do not use abrasive materials or aggressive cleaning agents to clean the LED fixture as this may damage the secondary optics. Instead use a clean dry fabric/cloth.
-
Do not use the LED fixture near flammable, explosive or reactive substances. The LED fixture can reach temperatures of 40° C.
-
Do not use sulphur vaporizers or water misters.
-
The installation and use of the LED fixture is the responsibility of the end user. Incorrect use or installation can lead to failure and damage to the LED fixture. Damage to the LED fixture and electronic circuitry as a result of incorrect installation and use revokes the warranty.
CONTENTS
INSTALLATION
WARNING
- Mounting and installing the LED fixture must be in accordance with the applicable local laws and regulations.
- The installer is responsible for correct and safe installation.
- Ensure the local cabling can support the voltage and current requirements of the LED fixture.
- Avoid coiled cords and keep mains leads separated to help prevent electromagnetic interference.
- Do not connect or disconnect the LED fixture under load.
Fixture assembly & installation
Note the direction when installing; the driver fixing bracket is on top when
fixture is hung.
Press button on the frame push-click connector to connect and ensure button
pops up in hole socket to lock.
Assemble the frame
Note the direction when installing; the driver tray is on top when the fixture is hung.
Connect the driver
Using PhotonTek 5m LED driver extension cords (sold separately), the driver can be positioned remotely for greater flexibility.
Connect the LED light bars
Replacing and changing light bars
Individual 1 00W light bars are available to purchase as replacements or with
different spectral ratios to adjust fixture spectral output.
The X 600W Pro fixture’s modular design has an intelligent LED driver which
can autosense and decrease or increase power to match the amount of 100W light
bars installed on the fixture.
WARNING At least one light bar must be installed in the fixture before switching on.
Installing the fixture
Mount the system to something that can hold the weight of the LED fixture.
Ensure all light bars are installed correctly and are secure. Carefully
turn the fixture over and attach the metal cable hangers to the mounting
hooks. Hang the fixture in required position and height. For optimal
performance; position fixture 30 – 50cm above plant canopy. Ensure the fixture
is hung horizontally.
Connecting the Manual Dimmer Control
The dimmer control is connected to the Dimming IN connector on the fixture.
This enables light intensity (PPF level) to be adjusted according to
requirement. The LED fixture light intensity can be adjusted without changing
spectral power distribution or losing efficiency.
Connecting Fixtures in series for External Control
For detailed instructions please refer to the PhotonTek Digital Lighting
Controller manual. The X 600W Pro uses 0-1 OV signal protocol for control.
Position and hang each fixture appropriately.
Connecting the LED fixture to the mains
WARNING
- Make sure mains power is switched off.
- Ensure the power supply cord is not coiled and does not touch any hot surfaces.
- Connect the cabling according to local rules, safety regulations and electrical code.
- Ensure external switching gear can cope with the inrush current of the LED fixture. Always use a double pole contactor suitable for switching a capacitive load. Never use household timers to switch the LED fixture!
- Ensure power cord rating matches mains supply voltage.
- The LED fixture is supplied with a 120V power cord for 120V power supply. 240V and 277V power cords are not included and must be purchased separately.
- Select the correctly rated cord for your mains power supply and connect driver power input socket to switching gear/power supply.
- Switch on mains power.
- Do not connect or disconnect the LED fixture under load.
PRECAUTIONS WHEN USING THE LED FIXTURE
- Always ensure at least one light bar is connected to the fixture before switching on. The X 600W Pro has an intelligent LED driver which will increase or decrease power to match the amount of light bars connected to the system.
- Always wait 20 – 30 minutes for the LED light bars to cool down.
INSPECTION, MAINTENANCE AND REPAIR
WARNING
- Disconnect the LED fixture from mains before performing any maintenance or repairs.
- Do not connect or disconnect the LED fixture under load
- Do not open or disassemble the LED fixture, it contains no serviceable parts inside. Opening the LED fixture can be dangerous and will void the warranty.
- Always wait 20 – 30 minutes for the LED light bars to cool down.
- Do not clean the LED fixture with detergents, abrasives or other aggressive substances.
- Regularly check the LED fixture for dust or dirt build up. Clean if necessary. Contamination may cause overheating and decreased performance.
- Clean the outside of the LED fixture using a dry or damp cloth.
- Regularly check the cords of the LED fixture to ensure it is undamaged.
STORAGE AND DISPOSAL
Store the LED fixture in a dry and clean environment, with an ambient
temperature of -25° C to 55° C.
The product must not be discarded as unsorted municipal waste but must be
collected separately for the purpose of treatment, recovery and
environmentally sound disposal.
WARRANTY
PhotonTek warrants the mechanical and electronic components of their product to be free of defects in material and workmanship if used under normal operating conditions for a period of five (5) years from the original date of purchase. If the product shows any defects within this period and that defect is not due to user error or improper use PhotonTek shall, at its discretion, either replace or repair the product using suitable new or reconditioned products or parts. In case PhotonTek decides to replace the entire product, this limited warranty shall apply to the replacement product for the remaining initial warranty period, i.e. five (5) years from the date of purchase of the original product For service; return the product to your shop with the original sales receipt
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>