Heat O32-IFT Cosmo Fireplaces Installation Guide
- August 2, 2024
- heat
Table of Contents
Heat O32-IFT Cosmo Fireplaces
Specifications
- Models : GLASS-32LINEAR, GLASS-36LINEAR, GLASS-42LINEAR
- Various models including COSMO, RAVE, JADE, DVLINEAR, SLR-X-AU, B41L-AU
Product Usage Instructions
Installation Instructions
Leave this manual with the responsible party for use and operation of the
fireplace.
CAUTION: Risk of Cuts or Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp. DANGER: Hot glass will cause burns. DO NOT TOUCH GLASS UNTIL COOLED. NEVER ALLOW CHILDREN TO TOUCH GLASS.
Installation Steps
- Turn off and cool the fireplace before proceeding with installation.
- Remove the decorative front and glass assembly according to the appliance installation manual.
- Locate and screw two self-tapping screws through the basepan holes into the back wall of the firebox.
- Bend the bottom glass tabs up on each side.
- Install the back glass panel ensuring the smooth side faces the front of the fireplace.
- Position the glass panel between the bottom glass tabs and side wall of the firebox.
Tools Required
- Screw gun equipped with 1/4 in. socket or 1/4 in. wrench or socket
- Standard Flathead Screwdriver
Kit Components
- (1) Left Refractory Panel
- (1) Right Refractory Panel
- (1) Back Refractory Panel
- (2) Side Glass Retaining Brackets with Screws
- (1) Back Glass Retaining Bracket with Screws (36 Only)
- (2) Self-tapping Base Pan Screws
Models : COSMO32-IFT, COSMO42-IFT, RAVE3012-IFT, RAVE4013-IFT, JADE32IN, JADE42IN, JADE42IL, COSMO32-IFT-B, COSMO36-IFT-B, COSMO42-IFT-B, RAVE32-IFT-B, RAVE36-IFT-B, RAVE42-IFT-B, JADE32IN-B, JADE42IN-B, JADE42IL-B, DVLINEAR36, SLR-X-AU, B41L-AU
Leave this manual with party responsible for use and operation.
CAUTION! Risk of Cuts or Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
DANGER
- HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH GLASS UNTIL COOLED. NEVER ALLOW CHILDREN TO TOUCH GLASS.
- A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and must be installed for the protection of children and other at-risk individuals.
- This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed. Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.
NOTICE : Handle refractory panels with care. Refractory may chip or crack if dropped or impacted.
TOOLS
- Screw gun equipped with 1/4 in.
- socket or 1/4 in.
- wrench or socket Standard Flathead Screwdriver
KIT COMPONENTS
- (1) Left Refractory Panel
- (1) Right Refractory Panel
- (1) Back Refractory Panel
- (2) Side Glass Retaining Brackets with Screws
- (1) Back Glass Retaining Bracket with Screws (36 Only)
- (2) Self-tapping Base Pan Screws
INSTALLATION
CAUTION! Risk of Burns! The fireplace should be turned off and cooled before the glass refractory is installed.
-
Remove decorative front and glass assembly. Refer to the appliance installation manual for glass removal and replacement instructions.
-
Locate the two holes on the back flange of the basepan, shown in Figure 1, and screw two self-tapping screws through the basepan and into the back wall of the firebox.
CAUTION: Risk of hard/aggressive lighting!
Installation of self-tapping screws is required. Appliance may cycle on and off and hard (aggressive) lighting could occur. -
Bend the bottom glass tabs, two on each side, up as shown in Figure 1.
-
Rear Panel : Install back glass panel as shown in Figure 2. Ensure the smooth side is facing toward the front of the fireplace. Set the back panel tight against the flange of the base pan and tilt the glass up toward the back of the firebox. Back panel will be held in place by the side panels. Hold back panel in place while installing the left and right panels.
GLASS-36LINEAR Only: Install back glass retaining bracket by centering it left and right and attaching it using two self-tapping screws. See Figure 3. -
Side Panels: Position glass panel between bottom glass tabs and side wall of firebox. See Figure 4.
-
Install side glass retaining bracket, one on each side, with the screw provided. Note that the size of the bracket depends on the model size. See Figure 5 (32 inch models) and Figure 6 (36 and 42 inch models). Repeat for opposite side panel.
-
Reinstall glass assembly and decorative front.
Hearth & Home Technologies
- 7571 215th Street West, Lakeville, MN 55044
- www.hearthnhome.com
Please contact your Hearth & Home Technologies dealer with any questions or concerns. For the location of your nearest Hearth & Home
Technologies dealer, please visit www.hearthnhome.com
2 Hearth & Home Technologies • GLASS-32LINEAR, GLASS-36LINEAR, GLASS-42LINEAR Installation Instructions • 2491-931 Rev. E • 2/24
FAQ
Q: What should I do if the integral barrier is missing?
A: Contact your dealer or Hearth & Home Technologies for assistance in
properly installing a barrier to prevent direct contact with the fixed glass
panel.
Q: What precautions should I take when handling refractory panels?
A: Handle refractory panels with care to avoid chipping or cracking.
Refractory may chip or crack if dropped or impacted.