FS1018PS1 Switch with 2 Gigabit Uplink and 1 SFP Port Instruction Manual

FS1018PS1 Switch with 2 Gigabit Uplink and 1 SFP Port

Product Usage Instructions

Hardware Connection

• Required Connections:
  • Connect the Power Socket to an AC power source.
  • Connect the PoE or Ethernet Device (switch, router, etc.) to the switch.
  • Connect the Powered Device (PD) such as an IP Camera, Wireless AP, Smart VoIP, Router, NVR, etc., to the switch.
  • Connect the switch to the Internet and a Monitor if necessary.

Physical Appearance

• Front board:
  • Gigabit Ethernet port
  • 16-Port 10/100M PoE+ Switch with 2 GbE and 1 Gigabit SFP Port FS1018PS1
  • 10/100Mbps PoE Port
• Back board:
  • Power input port (AC INPUT 100V-240V)
  • SFP Port

DIP Explanation

• VLAN (1-16 Port): Configure VLAN settings for specific ports.
• Port Isolation: Isolate downlink designated ports from each other.
• Default Extend (1-16 Port): Set standard switch link extension settings.

LED and Interface Explanation

• PWR Mode:
  • 1-19 Green: Equipment powered on
  • 1-16 Yellow (POE): Equipment power off
  • POE MAX (Green): Flashing – POE LED Button On – Equipment power off Off – VLAN mode On – Extend mode Flashing – Default mode
  • Indicators for link connectivity, data transmission, link abnormality, and POE power supply status are also provided.

Frequently Asked Questions (FAQ)

• Q: How can I reset the switch to factory settings?
  A: To reset the switch to factory settings, locate the reset button on the device and press it for at least 10 seconds until the indicators show the reset process is complete.

• Q: Can I use this switch with non-PoE devices?
  A: Yes, you can use this switch with non-PoE devices by connecting them to the non-PoE ports available on the switch.

Hardware Connection

Physical Appearance

Specifications

• Model: FS1018PS1
• Network Protocol:
  • IEEE802.3 / IEEE802.3u / IEEE802.3z
  • IEEE802.3x / IEEE802.3ab / IEEE802.3af/at
• PoE Standard: IEEE802.3at (30W) and IEEE802.3af (15.4w)
• Optical Media:
  • Multimode fiber:50/125,62.5/125,100/140um
  • Single mode fiber:8/125、8.7/125,9/125,10/125um
• AC Input Voltage: AC100~240V
• POE Voltage: DC 44-57 V
• Power Pin: Power over spare pairs 1/2(+) , 3/6 (-)
• Network Medium:
  • 10BASE-T: Cat 3,4,5 UTP(≤100 meter)
  • 100BASE-TX: Cat5 or more UTP (≤100 meter)
  • 1000Base-TX: Cat5 or more UTP/STP(≤100 meter)
• Output: 52V ~ 3.8A
• Total Power: 180W
• Dimension(L×W×H): 320mm×207mm×45mm
• Bandwidth: 9.2Gbps (non-blocking)
• Forwarding Rate: 6.8Mpps
• Packet Buffer: 3Mbit
• MAC Address: 2K MAC address table
• Transfer Mode: Store-And-Forward
• Working Temperature: -10~50℃
• Storage Temperature: -40~70℃
• Working humidity: 10%~90%, non-condensing
• Storage humidity: 5%~95%, non-condensing

DIP Explanation

LED and Interface Explanation

EU declaration of conformity

Cudy hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU.The original EU declaration of conformity may be found at http://www.cudy.com/

Email: support@cudy.com
Website: www.cudy.com

References

• Cudy, Your Home and Business Networking Solutions Provider
• Cudy, Your Home and Business Networking Solutions Provider

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>