VEVOR SR Series Truck Tonneau Covers Instruction Manual
- July 26, 2024
- VEVOR
Table of Contents
VEVOR SR Series Truck Tonneau Covers
Specifications
- Model: SRFD0955, SRGM1466, SRDG0264, SRGM1958
- Vehicle Compatibility:
- Ford F-150, 2015-2020, Short
- Silverado / Sierra 2014-2018/2019-2023, Standard
- Dodge Ram 1500 2500 3500, 2019-2023, Standard
- Silverado/Sierra, 2019-2023, Short
- Color: Black
- Material: Vinyl, Aluminum, Stainless Steel
INTRODUCTION
| SRFD0955 | SRGM1466 | SRDG0264 | SRGM1958 |
|---|
WARNING: ASSEMBLY PRECAUTIONS
- Keep children and pets away during assembly.
- Please assemble the product following the instructions carefully to avoid hazards.
- Separate and count all parts and hardware.
- Prepare a Philips Head Screwdriver.
- Follow the intended uses only.
Product Parameters
| Model | VEHICLE COMPATIBILITY | Color | Material |
|---|
SRFD0955
| ****
Ford ,F-150, 2015-2020, Short
| |
SRGM1466
| Silverado / Sierra，| | Vinyl,
2014-2018/2019-2023, Standard| Black| Aluminum,
Stainless
SRDG0264| Dodge Ram 1500 2500 3500,
2019-2023, Standard| | Steel
SRGM1958| Silverado/Sierra , 2019-2023,| |
Short| |
Part List
When unpacking this product, check to make sure the parts listed below are
included and carefully inspect for any damage that may have occurred during
transit. If any part is missing or damaged, do not attempt to assemble or use
the product.
- Cover Assembly – 1PCS
- Side Rail – 1PCS
- Allen Wrench – 1PCS
Installation Methods
Wash the truck bed.
- Installing the Cover Assembly: Place the cover on the top of the truck front rail, slide the driver’s side rail into the bulkhead, then tighten the front bulkhead assembly. Follow the same procedure to install the passenger’s side rail.
- Positioning Side Rails: Place the side rail on top of the truck side rail vertically leveled. Start at the tailgate and evenly space 3 clamps along each side. Leave approximately 6 to 8 inches space on each end.
- Tightening Clamps: Do not tighten clamps until all clamps are in proper position. Note: Clamps may vary by specific vehicles.
- Secure Velcro Fastener: Pull the cover over velcro fastener strips on one side of the rail, then press cover edges to the fastener. Follow the same procedure on the opposite side.
Tension Control System
The cover has been set at the factory for moderate tension to keep your cover
free of wrinkles. Depending on weather conditions it may be necessary for you
to adjust the tension control on the cover. To adjust the tension control,
simply loosen the screws on the tension plate,then slide the tension plate
towards the tailgate to a right scale line. Open the Cover
Roll the cover toward the cab making sure both sides of cover rolled evenly.
Secure the cover open by hooking the safety straps to the front loops.
Manufacturer: Shanghaimuxinmuyeyouxiangongsi
Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
Imported to AUS : SIHAO PTY LTD.1 ROKEVA STREETEASTWOOD NSW 2122
Australia
Imported to USA : Sanven Technology Ltd. Suite 250,9166 Anaheim
Place,Rancho Cucamonga,CA91730
Pooledas Group Ltd
Unit 5 Albert Edward House,
The Pavilions Preston, United Kingdom
pooledas123@gmail.com
01772418127
SHUNSHUN GmbH
Römeräcker 9 Z2021,76351
Linkenheim-Hochstetten, Germany
euvertreter@gmail.com
+49 1727041930
Made In China
Technical Support and E-Warranty Certificate
www.vevor.com/support
FAQ
Q: What should I do if any part is missing or damaged during unpacking?
A: If any part is missing or damaged, do not attempt to assemble or use
the product. Contact customer support for assistance.
Q: Can I use this tonneau cover on a different model of truck not listed in
the compatibility section?
A: It is recommended to use this tonneau cover only on the specified
vehicle models for optimal fit and performance.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>