ISOtunes IT-34B LINK Aware Bluetooth Ear Muffs Green Instruction Manual
- July 29, 2024
- ISOtunes
Table of Contents
ISOtunes IT-34B LINK Aware Bluetooth Ear Muffs Green Instruction Manual
HEARING PROTECTOR CLASS 5
Tested to AS/NZS1270, when selected, used and maintained as specified in
AS/NZS 1269 this protector may be used in noise up to 110dBA assuming an 85
dBA criterion. A lower criterion may require a higher protector class.
Please read, understand, and follow all safety information. This hearing protector is specifically designed for use in noisy environments, provided it is properly used and the protector remains clean and undamaged.
Models
IT-34B LINK Aware
IT-35B LINK Aware EN 352
Full manual can be found at: ISOtunes.com/manuals/LINKAware
****
Introduction
Thank you for purchasing ISOtunes LINK Aware. This product has been specifically designed for use in noisy environments – allowing you to block out much of the surrounding noise so that you can listen to your music or talk on the phone with less interruption.
Fitting
- Pull the earcups apart.
- Place the product on your head, securely covering both ears.
- Adjust the earcup position by extending the headband to ensure a good fit around the head and ears.
- When testing the fit, have the product turned off. This will allow you to ensure the passive hearing protection of this product.
- Properly fitted and secured earmuffs will significantly and noticeably reduce outside noise.
Boom Mic
To enhance phone or radio audio quality, use the ISOtunes Boom Mic (sold separately). The Boom Mic accessory is available for purchase at ISOtunes.com.
Inserting the Boom Mic __
- Open the microphone port cover on the right earcup by pulling down on the exposed tab, then align the base and the 3.5 mm jack of the Boom Mic and insert.
- Press firmly to ensure that it’s fully seated. 3. Remove the Boom Mic for storage or when not in use.
Power ON :
- In OFF mode, press and hold the multi function button (O) for 3 seconds.
- Device will say “ Power On.”
Power OFF: __
- In ON mode, press and hold the multi function button (O) for 3 seconds.
- Device will say “ Power Off.”
Bluetooth ® Pairing
- After powering on, the earmuffs will automatically enter Bluetooth Pairing Mode. 2. Open the Bluetooth settings on your device. Find “ISOtunes LINK Aware.”
- Pair and connect.
- You will hear “ Bluetooth Connected ” once connected.
Dual Connect __
This product can connect to two devices at the same time such as your phone and your computer.
- Pair and connect to your first device as described in “Bluetooth Pairing.” This will be Device A.
- Press and Hold the multi-function button (O) for 7 Seconds. First, you will hear “ Power Off ,” keeping holding the button until you hear “ Bluetooth Pairing Mode.”
- Pair and connect to the second device as described in “Bluetooth Pairing.” This will be Device B.
- On Device A, go to the Bluetooth menu and manually connect to ISOtunes LINK Aware. 5. Both devices are now connected.
If you are still having connectivity issues, please refer to the “Factory Reset” section of this manual for instructions or contact ISOtunes Support.
User Controls
A udio Volume __
The left buttons control your entertainment or phone call volume.
- UP (+): Increase the audio volume
- DOWN (-): Decrease the audio volume
A ware Volume __
The right buttons control your Aware, the level-dependent sound, volume.
- UP (+): Increase the Aware volume
- DOWN (-): Decrease the Aware volume
Phone Calls __
Your earmuff is enabled with a microphone that makes it easy to communicate over the phone. The controls for phone calls will operate the same with a boom mic installed.
- Answer/End Calls: Press multi-function button (O) once
- Reject Calls: Press and hold multi-function button (O) for 1 second
Voice Assistant __
Siri / Google Assistant: Press and hold the multi function button (O) for 1
second.
Experiencing issues? See the “Factory Reset” section or contact ISOtunes
Support.
Aware Technology
This product includes Aware Technology. This is a level-dependent technology that allows the user to hear the world around them. When noise breaches a safe listening level, the LINK Aware immediately responds and cuts out all environmental sound. This reverts the product to a passive hearing protection device. Your product will continue to play any entertainment or communication audio.
Levels __
LINK Aware has 10 levels of Aware:
- OFF
- Low: Levels 1-3
- Medium: Levels 4-6
- High: Levels 7-9
The levels are changed by pressing the UP (+) and DOWN (-) buttons on the right side of the control panel.
Signals __
A single beep means that the level has successfully been raised/lowered. A low-pitched double chime means that the lowest Aware level has been reached (OFF). A high-pitched double chime means that the highest Aware level has been reached.
Batteries and Charging
Charging __
- This product comes with a lithium battery pack. Begin by plugging the included charging cable into a wall outlet or computer port.
- Find the product’s charging port underneath the rubber cover on the bottom of the left earcup.
- Plug the USB-C end of the charging cable into the product’s charging port.
LED Indicators __
While the cable is plugged into the charging port, LED charging indicators will let you know when the battery is fully charged.
- Solid Red = Charging
- Solid Green = Fully Charged
Charging voltage should not exceed 5 V.
Checking or Reinstalling Battery __
- The batteries can be checked by removing the battery cover. Slide the latch to release the door.
- Lift the battery out. Unplug the battery pack cable.
- To reinstall, put the battery pack into the compartment. Then, plug the battery pack cable into the port.
- Ensure the battery pack cable is plugged in properly for proper product performance.
Replacement batteries are available via ISOtunes.com ****
Using AAAs __
- Alternatively, three AAA batteries can power the device. Slide the latch to release the door.
- Lift the battery out. Unplug the battery pack cable.
- Install the AAA batteries as indicated on the product.
- Do not attempt to use the lithium battery pack and AAA batteries at the same time.
Factory Reset
If you have issues connecting to any device, we recommend a factory reset. Make sure you “forget” or unpair the headphones from your device prior to doing a reset.
- Ensure the headphones are powered on.
- Press and hold the volume up button (+) and the volume down button (-) at the same time for four seconds.
- The product will enter pairing mode. Follow the pairing instructions to reconnect to your device.
Cleaning and Maintenance
Clean your ISOtunes LINK Aware by gently wiping them with a clean, damp cloth with mild soap.
Do Not __
- Immerse the hearing protector in water.
- Use abrasive cleaning solvents to clean the hearing protector.
If the hearing protector gets wet from sweat or rain, please discontinue use and turn the earmuff outwards and allow to dry. The ear cushions and foam liners should be regularly inspected for deterioration, cracking, or other damage.
Replacing Ear Cushions __
- Firmly reach into one earcup and tug on the plastic plate behind the ear cushion.
- Pull with force until the ear cushion is removed from the earcup. Do not twist, shear, or cut off. The cushions are secured with a strong snap fit. You may have to pull harder than you think!
- Remove the R or L indicating fabric and 2 layers of foam.
- Insert one new foam layer with notches. Align notches to the earcup.
- Insert second new foam layer.
- Insert the new R or L indicating fabric.
- Place on a new ear cushion and listen for a snap sound. Check that the ear cushion is secure on all sides.
- Repeat with the other earcup.
Replacement Parts __
LINK Hygiene Kit (ear cushions and foam inserts) Model Number: IT-83
Available at ISOtunes.com ****
SafeMax™ Technology
ISOtunes LINK Aware incorporates SafeMax™ Technology; therefore, its volume output is limited to 85 decibels (IT-34B), or 82 decibels (IT-35B). ISOtunes devices with SafeMax™ Technology are ANSI tested and OSHA compliant and, when designated, meet the European Safety Standard EN352.
Noise Attenuation
ISOtunes® LINK Aware is tested and approved in accordance with ANSI S3.19-1974 Specifications and the European Safety Standard EN 352- 1:2020, EN 352-4:2020, EN 352-6:2020, and EN 352-8:2020.
This earmuff is provided with level dependent attenuation. The wearer should check correct operation before use. If distortion or failure is detected, the wearer should refer to the manufacturers advice for maintenance and replacement of the battery.
American National Standards Institute (ANSI) S3.19-1974
The level of noise entering a person’s ear, when ISOtunes LINK Aware earmuffs are worn as directed, is closely approximated by the difference between the A-weighted environmental noise level and the Noise Reduction Rating (NRR). Improper fit of this device will reduce its effectiveness in attenuating noise. Consult the enclosed instructions for proper fitting.
A1: Frequency (Hz)
A2: Mean Attenuation (dB)
A3: Standard Deviation (dB)
Example:
- The surrounding noise level measured at the ear is 100 dB.
- The NRR of ISOtunes LINK Aware is 25 dB. 3. The noise level entering the ear is approximately equal mto 75 dB.
Please note that the NRR is based on the attenuation of continuous noise and may not be an accurate indicator of the protection attainable against impulsive noise, such as gunfire.
European Committee for Standardization (CEN) EN 352
This product has been tested and meets the European Safety Standard EN352-1:2020, RED directive 2014/53/EU, harmonized Standard EN 60065-2014+A11-2017, EN 62479:2020, ETSI EN 300 328 V2.1.1, ETSI EN 301 489-1 V2.1.1, ETSI EN 301 489-17 V3.1.1 and the ANSI standards for a hearing protector, with a Single Number Rating (SNR) of 30 dB with a Noise Reduction Rating (NRR) of 25 dB. Full testing details are available in the Noise Attenuation section of this booklet.
This product is certified according to the product standards EN 352-1:2020, EN 352-4:2020, EN 352- 6:2020, and EN 352-8:2020.
B1: Frequency (Hz)
B2: Mean Attenuation (dB)
B3: Standard Deviation (dB)
B4: Assumed Protection Value (APV) (dB) B5:
H = Hearing protection estimation for high frequency sounds (f ≥ 2000Hz)
M = Hearing protection estimation for medium frequency sounds (500 Hz < f <
2000Hz)
L = Hearing protection estimation for low frequency sounds (f ≤ 500Hz)
Criterion level is the sound pressure level in dB(A) of the noise environment resulting in 85 dB(A) effective to the ear while wearing hearing protectors. Three different criterion levels are defined related to the frequency content of the noise.
C1: H = criterion level for high-frequency noise C2: M = criterion level for medium-frequency noise C3: L= criterion level for low-frequency noise
It is recommended that the user should ensure that:
- The earmuffs are fitted, adjusted, and maintained in accordance with the manufacturer’s instructions.
- The earmuffs are worn at all times in noisy surroundings.
- The earmuffs are regularly inspected for serviceability.
If these recommendations are not adhered to, the protection afforded by the earmuffs will be severely impaired.
Recommended Storage – please store in a dry location between use.
AS/NZS 1270
The reported attenuation will be obtained only if the protector is in good condition and worn as directed by AS/NZS 1269.3.
Clamp Force: 10 N
Mass: 544 g
Product Lifetime: 3 years
D1: Means
D2: Standard Deviation
D3: Means – Standard Deviation
WARNINGS
ISOtunes LINK Aware does an excellent job of blocking outside noise. As such, ISOtunes LINK Aware should NOT be used in environments where users need to be fully aware of their surroundings for personal safety reasons. For example, do NOT use them while driving a car or riding a motorcycle. Similarly, do NOT use them when riding a bicycle outside. The user is solely responsible for ensuring that ISOtunes LINK Aware is used ONLY in safe environments.
The output of the electrical audio circuit of this hearing protector may exceed the daily limit sound level.
These earmuffs are intended to protect your ears against hazardous noise. The audibility of warning signals at a specific workplace may be impaired while using the entertainment facility.
This product may be adversely affected by certain chemical substances, such as sunscreen and bug spray. Further information may be sought from the manufacturer.
The fitting of hygiene covers to the cushions may affect the acoustic performance of the earmuffs.
Noise reduction will be adversely affected by anything that impairs the seal of the earmuff cushions against the head, such as thick spectacle frames, balaclavas, etc. Cushions may deteriorate with use and should be renewed regularly.
Additional Notes
Product Lifetime: 3 years
Materials:
- Ear Cushion: PU + Memory Foam
- Casing: ABS
- Key Pad: Silicon
- Headband: Stainless Steel + TPE
- Headband Bracket: ABS
The size range for the earmuff is S M L.
Performance may deteriorate with battery use. The typical period of continuous use that can be expected from earmuff battery is 23 hours.
ISOtunes LINK Aware is compliant with Bluetooth® V5.0. We do not guarantee compatibility of all functions on every Bluetooth®- enabled device. Please check your device’s user manual for compatibility and functionality.
Please note, the hearing protector provides an entertainment audio facility. The earmuff provides audio signal sound pressure level limitation which limits the entertainment audio signal to 82 dB(A) [IT-35B] or 85 dB(A) [IT- 34B] effective to the ear. This limit is maintained for bluetooth signal inputs which are standard to the Bluetooth A2DP, HFP, and HSP specifications. There is no analog line input on this product.
This earmuff is provided with electrical audio input. The wearer should check correct operation before use. If distortion or failure is detected, the wearer should refer to the manufacturer’s advice.
FCC
FCC ID: 2AJRD-IT-48
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the users’ authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC‘s RF radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co located or operating in conjunction with any other antenna or transmitter.
ISED Certification
IC ID: 29416-IT48
This device contains licence-exempt transmitter(s)/ receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence exempt
RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any
interference, including interference that may cause undesired operation of
the device.
SAR Warning
This equipment has to subject to ISED SAR
(Specific Absorption Rate) exposure test, this equipment is designed to meet the requirements for exposure to radio waves established by the ISED.
For additional information about ISOtunes LINK Aware please visit ISOtunes.com/manuals/LINKAware.
For additional information or questions about ISOtunes products or spares and accessories, please contact our support team.
UK & Europe
uk-eurosupport@isotunes.com
North America
support@isotunes.com ****
1-844-396-3737
+1 317-740-0419
Monday-Friday, 9-5 EDT
Hereby, Haven Technologies declares that ISOtunes LINK Aware (IT-35B) is in
compliance with the Regulation (EU) 2016/425 (PPE), Directive 2011/65/EU
(RoHS) and Directive 2014/53/ EU (RED).
The full text of the EU declaration of conformity is available at the
following internet address:
ISOtunes.eu/documents
This product is certified and monitored by PZT GmbH, Bismarckstrasse 264 B,
26389
Wilhelmshaven, Germany, NB 1974
Haven Technologies, Inc.
873 W. Carmel Dr.
Carmel, IN 46032, USA
ISOtunes.com
Haven Technologies DE
Winterhuder Weg 29 7. Fl
22085 Hamburg
Germany
ISOtunes® LINK Aware
IT-34B, IT-35B
The Bluetooth® word mark
and logos are registered
trademarks owned by
Bluetooth SIG, Inc.
Version 3.0
Creation Date: 7/17/2023
Updated Date: 03/04/2024
FCC ID: 2AJRDIT-48
IC ID: 29416-IT48
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>