SIRUS I-Amp 1.300T Power Amplifier User Manual
- July 24, 2024
- SIRUS
Table of Contents
- SIRUS I-Amp 1.300T Power Amplifier
- Product Information: I-Amp 1.300T Power Amplifier
- Product Usage Instructions
- General information
- Safety instructions
- Features
- Installation and starting up
- Connections and controls
- Technical specifications
- Plug and connection assignment
- Cleaning
- Protecting the environment
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SIRUS I-Amp 1.300T Power Amplifier
Product Information: I-Amp 1.300T Power Amplifier
Specifications
- Model: I-Amp 1.300T
- Type: Power Amplifier
- Date: 21.06.2024
- ID: 570052 (V2)
General Information
The I-Amp 1.300T Power Amplifier is designed to amplify audio frequency
signals for the operation of passive loudspeakers. It is intended for
professional use only. Any use other than described in the user manual is
considered improper and may result in personal injury or property damage.
Safety Instructions
Intended Use
This device is meant to be used by individuals with sufficient physical,
sensorial, and intellectual abilities along with the corresponding knowledge
and experience. Others should only use it under supervision of a responsible
person for their safety.
Safety
DANGER! Risk of injury and choking hazard for children! Danger to life due to electric current! High voltages may be present within the device. Never remove covers or use the device when safety equipment is missing.
DANGER! A short circuit could lead to a fire hazard and risk of death. Always use proper insulated mains cable with a safety plug. Do not modify the cable or plug. In case of isolation damage, disconnect the power supply immediately.
WARNING! Possible hearing damage due to high volumes on speakers or headphones! Avoid prolonged exposure to high volume levels as it may cause temporary or permanent hearing impairment. Reduce volume if you experience any hearing issues.
Product Usage Instructions
- Ensure the device is connected to passive loudspeakers only.
- Use the device only as described in the user manual.
- Keep covers intact and do not attempt to modify any parts internally.
- Always use proper insulated mains cable with a safety plug.
- Avoid prolonged exposure to high volume levels to prevent hearing damage.
FAQ
-
Q: Can this amplifier be used with active speakers?
A: No, this amplifier is designed for use with passive loudspeakers only. -
Q: What should I do if I experience a short circ uit?
A: In case of a short circuit, immediately disconnect the power supply and seek advice from a qualified electrician for repair.
User Manual
I-Amp 1.300T
Power Amplifier
Thomann GmbH
Hans-Thomann-Straße 1 96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
Internet: www.thomann.de
21.06.2024, ID: 570052 (V2)
General information
This document contains important instructions for the safe operation of the
product. Read and follow the safety instructions and all other instructions.
Keep the document for future refer‐ence. Make sure that it is available to all
those using the product. If you sell the product to another user, be sure that
they also receive this document.
Our products and documentation are subject to a process of continuous
development. They are therefore subject to change. Please refer to the latest
version of the documentation, which is ready for download under
www.thomann.de.
Symbols and signal words
In this section you will find an overview of the meaning of symbols and
signal words that are used in this document.
Signal word | Meaning |
---|---|
DANGER! | This combination of symbol and signal word indicates an |
immediate dangerous situation that will result in death or serious injury if
it is not avoided.
WARNING!| This combination of symbol and signal word indicates a
possible dangerous situation that can result in death or serious injury if it
is not avoided.
NOTICE!| This combination of symbol and signal word indicates a possible
dangerous situation that can result in material and environmental damage if it
is not avoided.
|
Warning signs| Type of danger
| Warning – high-voltage.
| Warning – danger zone.
Safety instructions
Intended use
This unit amplifies audio frequency signals for the operation of passive
loudspeakers. It is designed for professional use only. Use the device only as
described in this user manual. Any other use or use under other operating
conditions is considered to be improper and may result in personal injury or
property damage. No liability will be assumed for damages resulting from
improper use.
This device may be used only by persons with sufficient physical, sensorial,
and intellectual abilities and having corresponding knowledge and experience.
Other persons may use this device only if they are supervised or instructed by
a person who is responsible for their safety.
Safety
DANGER!
Risk of injury and choking hazard for children!
Children can suffocate on packaging material and small parts. Children can
injure themselves when handling the device. Never allow children to play with
the packaging material and the device. Always store packaging material out of
the reach of babies and small children. Always dispose of packaging material
properly when it is not in use. Never allow children to use the device without
supervi‐sion. Keep small parts away from children and make sure that the
device does not shed any small parts (such knobs) that children could play
with.
DANGER!
Danger to life due to electric current!
Within the device there are areas where high voltages may be present. Never
remove any covers. There are no user-serviceable parts inside. Do not use the
device when covers, safety equipment or optical components are missing or
damaged.
DANGER!
Danger to life due to electric current!
A short circuit could lead to a fire hazard and risk of death. Always use
proper ready-made insulated triple-core mains cable with a safety plug. Do not
modify the mains cable or the plug. In case of isolation damage, disconnect
immediately the power supply and arrange repair. If in doubt, seek advice from
a qualified electrician.
WARNING!
Possible hearing damage due to high volumes on speakers or headphones!
With speakers or headphones connected, the device can produce volume levels
that may cause temporary or permanent hearing impairment. Over an extended
period of time, even levels that seem to be uncritical can cause hearing
damage. Do not operate the device permanently at a high volume level. Decrease
the volume level immediately if you experience ringing in your ears or hearing
impairment.
NOTICE!
Risk of fire due to covered vents and neighbouring heat sources!
If the vents of the device are covered or the device is operated in the
immediate vicinity of other heat sources, the device can overheat and burst
into flames. Never cover the device or the vents. Do not install the device in
the immediate vicinity of other heat sources. Never operate the device in the
immediate vicinity of naked flames.
NOTICE!
Damage to the device if operated in unsuitable ambient conditions!
The device can be damaged if it is operated in unsuitable ambient conditions.
Only operate the device indoors within the ambient conditions specified in the
“Technical specifications” chapter of this user manual. Avoid operating it in
environments with direct sunlight, heavy dirt and strong vibrations. Avoid
operating it in environments with strong temperature fluctuations. If
temperature fluctuations cannot be avoided (for example after transport in low
outside temperatures), do not switch on the device immediately. Never subject
the device to liquids or moisture. Never move the device to another location
while it is in operation. In environments with increased dirt levels (for
example due to dust, smoke, nicotine or mist): Have the device cleaned by
qualified specialists at regular intervals to prevent damage due to
overheating and other malfunctions.
NOTICE!
Damage to the device due to high voltages!
The device can be damaged if it is operated with the incorrect voltage or if
high voltage peaks occur. In the worst case, excess voltages can also cause a
risk of injury and fires. Make sure that the voltage specification on the
device matches the local power grid before plugging in the device. Only
operate the device from professionally installed mains sockets that are
protected by a residual current circuit breaker (FI). As a precaution,
disconnect the device from the power grid when storms are approaching or it
the device will not be used for a longer period.
NOTICE!
Risk of fire due to installation of a wrong fuse!
Using fuses of a different type than compatible with the device may cause a
fire and seriously damage the device. Only use fuses of the same type. Observe
the labelling on the device casing and the information in the “Technical data”
chapter.
Features
- 1-channel installation amplifier
- 1 × 300 Watt @ 70/100 V (RMS)
- Class D amplifier
- Protection circuits such as thermal, short circuit, on/off muting
- Euroblock input and Euroblock output
- Volume control and mains switch installed on the front
- Signal, clip, protect and power LED
- 19-inch rack size (1 RU)
Installation and starting up
Unpack and check carefully there is no transportation damage before using the
unit. Keep the equipment packaging. To fully protect the product against
vibration, dust and moisture during transportation or storage use the original
packaging or your own packaging material suitable for transport or storage,
respectively.
Create all connections while the device is off. Use the shortest possible
high-quality cables for all connections. Take care when running the cables to
prevent tripping hazards.
DANGER!
Risk of death from electrical current!
The output voltages of modern high-performance amplifiers may result in death
or serious injury.
Never touch the bare ends of loudspeaker cables when the amplifier is on.
DANGER!
Risk of death from electrical current!
Hazardous voltage may be present at cable ends and screw terminals.
The connection of screw terminals and all maintenance and repair work on the
electrical installation of the device may only be performed by a qualified
electrician. Always perform maintenance and repair work when the device is
free from voltage. Failure to comply may result in electric shock and risk of
fire and loss of life.
Always observe all electrical safety instructions applicable in the country of
operation.
NOTICE!
Interference with nearby electrical devices due to magnetic fields!
The device generates strong magnetic fields that can interfere with the
function of poorly shielded devices. The magnetic fields are strongest
directly above and below the Power Amplifier.
You should therefore never place sensitive devices such as pre-amplifiers,
radio transmission systems, or tape decks directly above or below the Power
Amplifier. When placing the Power Amplifier in a rack, you should place it at
the bottom thereof, and place any other equipment at the top of the rack.
Rack mounting
The unit has been designed for rack mounting in a standard 19-inch rack; it
occupies one rack unit.
Input signal
The input signal is connected to the Euroblock terminals ([INPUT] channel
terminals). The sup‐plied sockets are used for this purpose.
- To connect an unbalanced input signal, use the [+] and [G] terminals.
- To connect a balanced input signal, use the [+], [-] and [G] terminals.
Speaker connection
The device is equipped with two Euroblock terminals that can be used to
connect ELA speakers (70-V technology or 100-V technology). You need to set
the relevant operating mode (70 V or 100 V) via the DIP switch.
Observe the following diagram when connecting the loudspeakers. The total
power consumption of the connected speakers must be below the maximum power of
the amplifier. We rec‐ommend a power reserve of 20%.
In the example, three 100-V speakers connected in parallel are connected to
two speaker connections that form two speaker zones.
Connections and controls
1 | Mains switch. Turns the device on and off. |
---|---|
2 | Channel control for input signal gain. |
3 | [CLIP] |
control to reduce the signal level until the LED goes out.
4| [SIG] | Lights up when an output signal is received.
5| [PROT] | Lights up when the protective circuit has tripped or the device
is defective. No sound is output. Make sure that the vents of the device are
free and that good ventilation is possible. Reduce the volume on the device.
Once the problem is resolved, the protection circuit is automatically reset
and the device is ready for use.
6| Channel LED lights up green when the device is on.
Rear panel
1| [INPUT] | Signal input, designed as Euroblock terminals
---|---
[+] | Balanced or unbalanced signal input (+)
[-] | Balanced signal input (-); remains free in case of unbalanced input
signals
[Ground] | Ground (GND)
2| [PRE-SET] | DIP switch for selecting the operating mode (70 V or 100 V)
3| [SPEAKER OUTPUT] | Euroblock terminals as speaker output
4| Rubber panel plug for power supply with fuse holder. Before connecting to
the power supply, check that the voltage selector on the bottom of the unit is
in the correct position.
Technical specifications
Amplifier class | Class D |
---|---|
Input impedance | 20 kΩ (balanced) |
10 kΩ (unbalanced)
Output power| 300 W RMS
Frequency response| 140 Hz … 15 kHz
Signal-to-noise ratio| > 95 dB
Crosstalk| > 70 dB
Total harmonic distortion (THD)| < 0.1%
Damping factor| > 200
Sensitivity| 0.9 V … 1.1 V (0 /–1 dBv)
Gain| 40 dB (100 V)
Power consumption| 400 W
Supply voltage| 230 V 50 Hz
Fuse| 5 mm × 20 mm, 2 A, 250 V, slow blow
Dimensions (W × H × D)| 483 mm × 44 mm × 360 mm
---|---
Weight| 5.2 kg
Ambient conditions| Temperature range| 0 °C…40 °C
Relative humidity| 20%…80% (non-condensing)
Plug and connection assignment
Introduction
This chapter will help you select the right cables and plugs to connect your
valuable equipment in such a way that a perfect sound experience is ensured.
Please note these advices, because especially in ‘Sound & Light’ caution is
indicated: Even if a plug fits into the socket, an incorrect connection may
result in a destroyed power amp, a short circuit or ‘just’ in poor
transmission quality!
Balanced and unbalanced transmission
Unbalanced transmission is mainly used in semi-professional environment and in
hifi use. Instrument cables with two conductors (one core plus shielding) are
typical representatives of the unbalanced transmission. One conductor is
ground and shielding while the signal is transmitted through the core.
Unbalanced transmission is susceptible to electromagnetic interference,
especially at low levels, such as microphone signals and when using long
cables.
In a professional environment, therefore, the balanced transmission is
preferred, because this enables an undisturbed transmission of signals over
long distances. In addition to the conductors ‘Ground’ and ‘Signal’, in a
balanced transmission a second core is added. This also transfers the signal,
but phase-shifted by 180°.
Since the interference affects both cores equally, by subtracting the phase-
shifted signals, the interfering signal is completely neutralized. The result
is a pure signal without any noise interference.
Cleaning
Fan grids
The fan grids of the device must be cleaned of any contamination, such as
dust, etc. on a regular basis. Before cleaning, switch off the device and
disconnect mains-operated devices from the mains. Only use pH-neutral,
solvent-free and non-abrasive cleaning agents. Clean the unit with a slightly
damp lint-free cloth.
Protecting the environment
Disposal of the packing material
Environmentally friendly materials have been chosen for the packaging. These
materials can be sent for normal recycling. Ensure that plastic bags,
packaging, etc. are disposed of in the proper manner.
Do not dispose of these materials with your normal household waste, but make
sure that they are collected for recycling. Please follow the instructions and
markings on the packaging.
Observe the disposal note regarding documentation in France.
Disposal of your old device
This product is subject to the European Waste Electrical and Electronic
Equipment Directive (WEEE) as amended.
Do not dispose of your old device with your normal household waste; instead,
deliver it for controlled disposal by an approved waste disposal firm or
through your local waste facility. If in doubt, consult your local waste
management facility. You can also return the device to a retailer if they
offer to take the device back for free or if they are legally obliged to do
so. When disposing of the device, comply with the rules and regulations that
apply in your country. You can also return your old device to Thomann GmbH at
no charge. Check the current conditions on
www.thomann.de.
Proper disposal protects the environment as well as the health of your fellow
human beings. This is because the proper handling of old devices negates the
potential negative effects of hazardous substances, and because it conserves
resources by recycling them.
Also note that waste avoidance is a valuable contribution to environmental
protection. Repairing a device or passing it on to another user is an
ecologically valuable alternative to disposal.
If your old device contains personal data, delete those data before disposing
of it.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>